Cuman Appian CP-100G User manual

CONFIDENTIALCONFIDENTIAL

CONFIDENTIAL
CP-100G
1) Device and Accessories
CP-100G Owner’s Manual
2
USB Cable
Waterproof Case
for Pets (Option) USB Recharger (Option)
I. Getting to Know Your GPS Personal Tracker
CONFIDENTIAL

CONFIDENTIAL
CP-100G
I. Getting to Know Your GPS Personal Tracker
2) Introduction to CP-100G
3
Part Feature
ⓐLED Window Displaying status of Device
ⓑSIM Card Slot Inserting GSM SIM Card
ⓒUSB Slot Program Update by USB Cable
Battery Recharge by USB Cable
ⓓReset Button Reset your Device
ⓔPower Button Turn ON & OFF
ⓕSOS Button Send SOS Message
CONFIDENTIAL

CONFIDENTIAL
CP-100G
3) Charging the Battery
New battery built in CP-100G is shipped partially charged. Before you use CP-100G, you need to charge
the battery as described below. Some batteries are performing the best after several full charge/discharge
cycles. Before you start charging battery, make sure CP-100G is power off.
I. Getting to Know Your GPS Personal Tracker
RED LED shall be on
when battery level is low
USB Cable
LED indicator for charging status
“ How to charge the battery”
1. Power off ( Press and hold ‘Power Button’for 5 seconds)
2. Connect CP-100G with your PC or USB Recharger using USB Cable.
3. It shall take 4~5 hours to fully recharge battery but it might be a little different depending on the
battery condition.
4. LED indicator on the top side of USB Cable connector shall be turned on RED while charging
battery, and it shall be changed to GREEN when battery is fully charged.
CUMAN recommend to keep charging for 4 hours at least although LED indicator changed to
GREEN a couple of hours after you start charging.
4
CONFIDENTIAL

CONFIDENTIAL
CP-100G
4) Inserting SIM Card
You should make sure CP-100G is POWER OFF before you insert SIM card. If you insert SIM card while
CP-100G is POWER ON, it might be not properly working, and in this case, you may remove SIM card
from CP-100G and press reset button. Open the rubber cover at the right side and slide the SIM card into the
SIM Card Slot beneath USB slot.
* Note: CP-100G shall not work at all without SIM card
•Slide SIM card into slot by correct direction
as shown above.
I. Getting to Know Your GPS Personal Tracker
Open the rubber cover
5
CONFIDENTIAL

CONFIDENTIAL
CP-100G
II. Starting Up
1) Features of Location Tracking Device, CP-100G
CP-100G was designed for 2 kinds of Operation Modes, Person to Person (P2P) and Operator to
Customer (B2C). This manual shall introduce the features of CP-100G by P2P mode only, and you can
trackyour kids, pets and assets by SMS of pre-assigned simple command sets, using your mobile phone or
Smartphone or PC.
A. Commands to Set Up CP-100G for …..
a). The Control Phone number to receive status of CP-100G
b). The time period for location report
c). The area to allow moving zone
d). The local time where you are using your device by adjusting from GMT
B. Reporting for …..
a). The Location periodically using GPS
b). The Location immediately using GPS
c). Zone out as being beyond allowed zone that you can set up by yourself
d). My Zone Out as being beyond the point set up by yourself
e). SOS / Emergency
f). Battery Warning / Low Battery
6
CONFIDENTIAL

CONFIDENTIAL
CP-100G
II. Starting Up
2) Turning your device ON and OFF
Low battery Indication LED
GSM Error Indication LED
Operation Indication LED
A. Power ON
Press and hold ‘Power Button’for 5 seconds, and then, each LED shall be turned on and blink 3
times by one after another. You can release Power Buttononce LED starts blinking.
B. Power OFF
Press and hold ‘Power Button’for 5 seconds, and you shall see all the LED lights shall blink 3 times
at the same time. You can release Power Buttononce LED starts blinking.
7
CONFIDENTIAL

CONFIDENTIAL
CP-100G
II. Starting Up
3) Battery Capacity
The Batterycapacity shall depend on operating conditions including mobile network, GPS level and/or
reporting period etc. By default, CP-100G is set to wake up every 30 minutes to fix GPS and check up
GSM network, automatically updating for the most ideal operating condition.
Below table can be reference when you set up Periodic Report described in page 12 of this manual.
Reporting Period Standby & Working Time Remarks
1 Minute 7 Hours Reporting location every minute
10 Minutes 35 Hours Reporting location every 10 minutes
30 Minutes 70 Hours Reporting location every 30 minutes
1 Hour 80 Hours Reporting location every hour
2 Hours 90 Hours Reporting location every 2 hours
4 Hours 100 Hours Reporting location every 4 hours
23 Hours 110 Hours Reporting location every 23 hours
8
(The above standby and working time was measured under normal condition of mobile network and GPS)
CONFIDENTIAL

CONFIDENTIAL
CP-100G
A. Some carriers’ (Mobile Phone Service companies) SIM Card may require PIN CODE before you start
using for the first time or anytime when the power of your device is turned on.
B. Your Device, CP-100G can only work with SIM Card free from PIN CODE restriction, and you may
check up the SIM Card before you insert into CP-100G if it requires PIN CODE.
1. Insert SIM Card into your mobile phone to see if PIN CODE is required.
2. If PIN CODE is required by carriers, you may input PIN CODE given by carriers to activate SIM Card
and set PIN CODE function to be “DISABLE“ or “OFF“. It is various depending on mobile phone
manufacturers and models, but you may usually find out PIN CODE function control in the menu of
Phone Setting.
C. You can also check up if SIM card in CP-100G can be workable using CP-100G.
1. Yellow LED shall be turned on if PIN CODE is required or SIM Card is the defected.
2. You can use SIM Card if there is no yellow LED turned on.
D. First GPS Fix of your device, CP-100G
When you start using CP-100G for the first time, CUMAN strongly recommend for you to keep CP-100G
out in the widely open sky area for about 10 minutes at least to fix GPS for the first time.
Once CP-100G fix initial GPS data, it shall be working as fast as “Hot Start Condition” whenever it is
required to report location information.
II. Starting Up
4) Your SIM Card to be inserted into Your Device, CP-100G
9
CONFIDENTIAL

CONFIDENTIAL
CP-100G
III. Set Up Your Device
All the Commands to use CP-100G should be edited by format of SMS. For more convenient use , CP-100G can
be controlled by simple format of Commands. CUMAN recommend for you to save all the Commands described
in this manual into Templates Folder of Control Phone (ex. your mobile phone) before you start using the Device.
A. Command to Register Control Phone No. (R)
1. You should register your ControlPhone No. to communicate with CP-100G, sending command to and
getting report from CP-100G.
2. You can track and control up to 9 sets of CP-100G with 1 set of your Control Phone Number, and you
shall designate identification number of each device in numeric from 1 to 9.
3. You can choose any 4 digit of numeric and register your own Password.
Default password by Factory was set as “ 0000 “ in numeric.
4. When you turn on the power of CP-100G for the first time, you shall see Blue LED
at the left shall remain turned on as shown at the right.
5. Once CP-100G is registered by R command from your Control Phone, Blue LED
at the left shall be turned off immediately.
6. You shall send Registration Command (R) by below format to CP-100G.
* SMS Command to CP-100G : R 10000 XXXX
* Reply from CP-100G : HP=D001=REGISTERED=IMEI-35900803???????
* IMEI No. of your device shall appear by 15 digits as above.
* Notes for Command : “ 1“ is a sequence ID of your device, CP-100G.
“ 0000 ” is a default password set by factory.
“ XXXX “ is your own password to be created by yourself.
** You should allow space between command letter and each password as shown above.
10
CONFIDENTIAL