Cyber ExerCycle User manual

Cyber ExerCycle
Cyber ExerCycleCyber ExerCycle
Cyber ExerCycle TM
TMTM
TM
Game Controller for Your Exercise Equipment
Game Controller for Your Exercise EquipmentGame Controller for Your Exercise Equipment
Game Controller for Your Exercise Equipment
USER GUIDE
Rev 1

1
TA LE OF CONTENTS
TA LE OF CONTENTSTA LE OF CONTENTS
TA LE OF CONTENTS
1. INSTALLING CYBER EXERCYCLE ON YOUR BIKE ................................................ 2
2. CONFIGURE CYBER EXERCYCLE............................................................................... 4
3. CONNECTING THE CONTROLLER TO A PC .............................................................. 6
4. CONNECTING THE CONTROLLER TO AN ANDROID TABLET ............................. 8
5. REQUIREMENTS..............................................................................................................
6. PRECAUTIONS ............................................................................................................... 10
7. TERMS AND CONDITIONS .......................................................................................... 11
8. RETURN AND WARRANTY......................................................................................... 11

2
1. INSTALLING CYBER EXERCYCLE ON YOUR BIKE
Connect Cyber ExerCycle to your exercise equipment in three steps:
• Attach the sensor and the magnet to the pedals of your bike
• Mount the controller to the frame of your bike.
• Plug the controller into a US port of your computer or tablet.
Attach the sensor to the stationary parts of the bike. Run the sensor cable up the frame.
Wrap the cable around the frame if required, so that the cable is not loose. Ensure that
the cable will not get tangled in the pedals.
Note the orientation of the sensor to get correct forward pedaling direction.
Mount the magnet so that it does not interfere with the sensor (ensure that the
minimum distance between the sensor and the magnet is between 0.25" to 1").
If the crank arm is made our of steel, the magnet may simply stick to the metal.
Optionally use double sided tape to attach the magnet.
As you move the pedals the magnet should come close to the sensor once per full
rotation on the crank set.

3
Mount the controller box to the frame of your bike using Velcro. The controller box
should typically be located close to the bike handles (makes handling the joystick easier)
The sensor attaches to the controller box using 2.5mm plug.
PC or tablet connects to the controller box through the mini US connector.
If you have any questions regarding the installation, please email us at
[e-mail]

4
2. CONFIGURE CYBER EXERCYCLE CONTROLLER
Cyber ExerCycle (CEC_KIT_ANDR) interfaces to a PC or an Android Tablet and emulates a
joystick. It provides you with pedaling feedback (forwards and backwards) in response
to pedaling action and also with a nunchuk style joystick used for steering.

5
The controller allows you to configure pedaling intensity. This determines on how fast
you need to pedal to move your character or a vehicle on the screen. The settings range
from very easy (40 RPM) to very hard (185 RPM). The maximum speed you can set the
controller is 185 rpm (equivalent to 3 rotations of the cranks per second).
The maximum pedalling speed corresponds to the maximum output of the joystick.
The maximum speed is set by pedaling and pressing a sequence of nunchuk joystick
keys to save the new setting.
• Pedal at your maximum speed.
• Press both buttons "C" and "Z" and move the nunchuk knob fully forward.
• You should see the LED block rapidly. The new setting is saved.
• Press "C" and "Z" and move the joystick backwards to set the default speed of
185 rpm.
Some games work better when you set the pedaling speed low. Always try the lower
speed first and increase the speed setting to increase the intensity of the exercise.
Once configured, the controller will remember your selections even if the controller is
connected to another PC or tablet.

6
3. CONNECTING THE CONTROLLER TO A PC
Connect the game controller to your PC using the supplied US cable. The controller
operates as a standard HID device, therefore does not require any special drivers. The
controller requires US port 1.0 or later.
After connecting the controller to your PC, Windows will automatically install all the
required driver. When powered and running the status LED on the side of the controller
box will turn on green .
Confirm the installation of the device by opening the control panel and viewing installed
devices. In the control panel the controller shows as a game pad.

7
Verify the operation of Cyber ExerCycle:
• Pressing "Z" button on the joystick should make the LED on the controller turn
solid green.
• Moving the magnet close to the sensor forces the status LED to turn sold green.
As you move the magnet away, the status LED should start blinking again.
• Open Game Controller Properties and try different controller inputs such as
pressing buttons, shaking the joystick. When pedaling you should see the Y Axis
of the display move.
• As you pedal forward on your bike the small cross should move up (reach the top
when you pedal fast). As you stop pedaling the cross should move back to the
center (within few seconds).
This version of the controller only emulates joystick interface. This version does not
provide keyboard or mouse emulation. You can play PC racing games that use joystick
interface. In game configuration may be required to match the game controls to the
controller actions.

8
4. CONNECTING THE CONTROLLER TO AN ANDROID
TABLET
Connect the game controller to your tablet using the supplied US cable. When using
Android devices you may require US OTG to US 2.0 Adapter Cable compatible with
your Android device (not included).
Confirm that your tablet supports external US devices by connecting your own US
mouse or a keyboard and checking their functionality. Also confirm that you can safely
place your tablet on the stationary bike.
The controller operates as a standard HID device, therefore does not require any special
drivers. When powered and running the status LED on the side of the controller box will
turn on green.
Once you connect the controller the interface should be operational (Please note that for
some games in-game configuration may still be required). If the controller is not
detected by the game try disconnecting the controller and reconnecting it. Also try
restarting a game while the controller is connected. Disconnect the controller when not
in use.
Once connected verify the operation of Cyber ExerCycle:
• Pressing "Z" button on the joystick should make the LED on the controller turn
solid green.
• Moving the magnet close to the sensor forces the status LED to turn sold green.
As you move the magnet away, the status LED should start blinking again.

5. REQUIREMENTS
Compatible with Android OS 3.1+,
Android OS 3.1+,Android OS 3.1+,
Android OS 3.1+, it also compatible with Windows XP, Windows Vista,
Windows XP, Windows Vista, Windows XP, Windows Vista,
Windows XP, Windows Vista,
Windows 7
Windows 7Windows 7
Windows 7,
, ,
, Windows
Windows Windows
Windows 8
88
8.
This version of the controller only emulates joystick interface. This version does not
provide keyboard or mouse emulation. You can still play PC racing games that use
joystick interface.
The setup utility is not required to configure the controller.
Please confirm that your PC meets minimum requirements of the games you wish to
play.
Many of the games provide a free demo download, allowing you to evaluate the game
and your computer performance. Please contact respective game manufacturer for game
support.
Powering the controller from the tablet draws some current from its battery. See
information from Google: "Connect to keyboards, mice, & other devices"