WinWing Super Libra J1 User manual

F18 GRIP+ J1 SUPER LIBRA JOYSTICK BASE
User manual
V 1.1
1J1-SUPER LIBRA JOYSTICK BASE Product Introduction ............................................1
1.1 Function introduction...............................................................................................2
1.2 Disassembly steps ..................................................................................................3
1.3 Median calibration and median offset .....................................................................6
1.4 Assembly steps .......................................................................................................7
1.5 Damping adjustment ...............................................................................................9
1.6 AM and Spring settings ...........................................................................................9
2F18-JGRIP Product Introduction ..................................................................................11
2.1 Key map introduce ................................................................................................11
2.2 Joystick Grip installation angle introduction ..........................................................12
2.3 Combinations of products (optional) .....................................................................13
3J1-HOLDER..................................................................................................................14
3.1 J1-HOLDER Adjustment instructions....................................................................14
4Other installation methods(Official advice) ...................................................................16
4.1 Gaming chair installation.......................................................................................16

1
1J1-SUPER LIBRA JOYSTICK BASE Product Introduction
①F18-JGRIP;
②Z axis kit;
③Adjustable Extension rod;
④J1-JOYSTICK BASE;
Activity range
1
2
3
4

2
1.1 Function introduction
1. Pitch axis rotation angle is ±20°;
2. Roll axis rotation angle is ±20°;
3. Yaw axis rotation angle is ±15°.
Yaw±15°
Roll±20°
Pitch±20°
Yaw±15°
Pitch±20°
Roll±20°

3
1.2 Disassembly steps
4 PCS
8 PCS
1
2
3

4
4
5
6
7
8

5
1、Remove 12 screws as shown.
2、Move the bottom plate and the outer casing to open the bottom plate.
3、Unplug two connectors.
4、Remove the shell and bottom plate.
5、Use the pliers to pull the illustrated screw outward, remove and replace the spring.
6、Use a wrench to remove the captive screws.
7、Remove and replace the curved arm.
8、Use a wrench to push the screw and press the screw into the hole.

6
1.3 Median calibration and median offset
Hold the handle firmly at the target position with your hand, and adjust the clearance between
the top wire and the wrench to adjust the gap to no gap (median deviation ±5°).
`
1. Rotate the left and right two top screws clockwise to eliminate the clearance;
2. Rotate the left and right two top screws counterclockwise to eliminate the clearance;



1
2

7
Note: The protrusion distance of the two top wires should be bilaterally symmetrical when in
the middle position.
1.4 Assembly steps
4 Pin
1
2
6 Pin
4 PCS

8
1. Plug in the lab connectors,
2. The assembly of the bottom plate and the housing requires the use of a wrench to fix the four
M3 screws shown in the figure;
3. Install upside need to use the wrench to fix the four M3 screws and four M4 screws.
4 PCS
4 PCS
3

9
1.5 Damping adjustment
Turn the wrench clockwise downward to increase the damping and vice versa. (Note: Do not
loosen excessively)
1.6 AM and Spring settings
Introduction of different feedback on settings.
Configuration introduction table
□
1
□
2
Roll
Pitch



10
Matching plan
Installation
location
J1-BASE
+F18-JGRIP
1-BASE
+Z Axis
+F18-JGRIP
J1-BASE
+Extension
+F18-JGRIP
J1-BASE
+Z Axis
+Extension
+F18-JGRIP
□
1
5#spring
6#spring
（Default）
□
2
4#spring
5#spring
4#spring
A richer operating experience can be achieved by changing the bending arm, spring and
spring mounting position. Among them, the S-bend arm has a smooth transition in the middle
position, and the middle position of the H-bend arm has a clear scale. It is not recommended to
combine the default spring and the number 3 spring or use in pairs.

11
2F18-JGRIP Product Introduction
2.1 Key map introduce
1st
2nd
7
1
A
d
f
7
A
d
f
7
12
A
d
f
7
A
d
f
7
A
d
f
7
A
d
f
7
13
11
14
15
A
d
f
7
A
d
f
7
A
d
f
7
A
d
f
7
A
d
f
7
8
A
d
f
7
A
d
f
7
A
d
f
7
A
d
f
7
A
d
f
7
2
3
4
5
6
A
d
f
7
17
A
d
f
7
16
A
d
f
7
A
d
f
7
9
10
18
19
21
20

12
2.2 Joystick Grip installation angle introduction
The extension rod, Z-axis kit and F18-JGRIP can be installed at any angle from 0-360°during
the docking process. (Illustration example ±45°two positions installed)
Note: Keep the components fixed during the docking process, and only twist the knurled cover
to achieve docking. Otherwise, the wiring will be twisted and broken.
Please reference< FA18 HOTAS INSTALL GUIDE EN V 1.1> part 3.2

13
2.3 Combinations of products (optional)
1、J1-BASE+Z Axis+Extension+F18-JGRIP
2、J1-BASE +Extension+F18-JGRIP
3、J1-BASE+Z Axis +F18-JGRIP
4、J1-BASE+F18-JGRIP
The four matching schemes are all connected with J1-HOLDER. For additional installation,
please go to the official website (www.winwing.cn) to download the drawings.

14
3J1-HOLDER
3.1 J1-HOLDER Adjustment instructions
The total thickness limits of the table and the block mat is 30mm to 70mm. Install 30mm
spacers as required.
The height difference between J1-BASE and the desktop can be changed by adjusting J1-
HOLDER (minimum 315mm, maximum 345mm.)

15
ADJUST

16
4Other installation methods(Official advice)
4.1 Gaming chair installation
Those kits are not include in the package.
①4 of M6 type Flat screw gasket
②4 of M6 type Elastic screw gasket
③4 of M6 30mm-type Allen screws
3
2
1

17
CAUTION: DO NOT USE SCREWS LONGER TOO MUCH TO INSTALL THE BASE ,OR WILL
BROKEN PCB INSIDE.
Mounting size as shown on picture
If you need drawings, please go to the official website to download (www.winwing.cn)