Cygnet U32A1D User manual

operation of this cut-out it is essential
to keep the heating element free from
scale. Failure to do this will result in the
cut-out operating before the water has
boiled.
Cleaning
WARNING Disconn ct from
th mains supply b for cl aning
and allow th urn to cool.
IMPORTANT Do not immerse the
urn in water or any other liquids and
take care to keep water away from the
mains lead and connections.
IMPORTANT Do not use any
abrasive cleaning fluids or materials.
1Wash out the urn. Use clean water
and a soft cloth.
2Brush any scale or sediment from
the element.
3Rinse thoroughly and buff with a
dry cloth.
• Do not clean with a water jet.
Descaling
In hard water areas scale will form
on the element and walls. This will
adversely affect the operation of the
urn if allowed to accumulate.
Descaling can be simply achieved by
using a proprietary descaler. Choose
one recommended for stainless steel
kettles. It is important to follow the
instructions given on the descaling
solution carton.
Scale build-up can also cause the
tap to drip even when in its closed
position. If this should occur
disconnect from the mains supply,
empty the urn, allow it to cool and
unscrew the top of the tap from the
body of the tap. Wipe, scrape and
break the scale away from the rubber
flexible seal and also from the sealing
surface inside the plastic body of the
tap.
IMPORTANT Failure to de-scale
will invalidate your guarantee.
Guaran ee
This electric catering urn is
guaranteed for a period of 12 months
from the date of purchase against
defective materials or faulty
workmanship.
This guarantee is given subject to
the urn being used in accordance with
the instructions on the supply voltage
marked on it and to the usual fair wear
and tear conditions.
The guarantee does not cover
consequential damage arising out of
any failure acceptable under
guarantee, nor does it cover damage
resulting from misuse, accident or
unauthorised alterations to the urn.
In any communication with the
supplier or manufacturer, it is essential
to quote the catalogue number
marked on the urn.
Proof of purchase will be required.
In any communication with the
service department, it is essential to
quote the model and serial number
marked on the rating label.
This guarantee, in no way
diminishes the buyer’s statutory rights.
Please fill in and return the tear
off section to register the guarantee
with Burco.
Spare parts
Element 3kW 59151
Tap 62584
Actuator 59728
Thermostat 62102
Marketing Department
Burco Appliances Ltd
Talbot Road Mexborough
South Yorkshire
S64 8AJ
Affix
postage
stamp
here
1
0
6
5
4
3
2
www.burco.co.uk
Covers U32A1D (S U 444448541),
U34A1D (S U 444448651) and
U36A1D (S U 444448542) models
Getting the best from
your urn...
• Remove any plastic film from the urn before use.
• Any water in the urn is due to testing and is
normal.
• The urn must be used on a flat level surface.
• Boil and discard the water twice before general
use.
0871 222 2620
0844 815 3744
Electric
catering urn
Please read and
keep these
instructions
Burco products are intended for commercial use as detailed in these
instructions.
Burco has a policy of continuous improvement in product quality and
design. The Company, therefore, reserves the right to change the
specification of its models at any time.
CP62091 Rev5 10/08
Burco Commercial Ca ering Equipmen
Glen Dimplex Professional Appliances
Stoney Lane, Prescot, Merseyside, L35 2XW
Tel [phone] Fax [phone]
Email [email protected]
CP149435MUK-62091Rev5-Cygnet:8749 Bu co boile s 4pp 15/10/08 10:37 Page 1

Guaran ee regis ra ion
Appliance model
Serial no.
Date of purchase
Customer name
Address
Pl as h lp us to furth r improv our products by ticking th on
main r ason for purchas
Price IIStyling/Appearance II
Features IIPrevious Burco ownership II
Dealer recommendation IIService back-up II
Other (please state)
Where did you buy your Burco appliance ?
Dealer/Retailer
Would you like more information on Burco products?
Yes IINo II
If you would lik to r c iv information on n w BURCO products
pl as supply your mail addr ss b low:
3
trapped under the terminals. Tighten
the clamp in the plug making sure that
it grips the outer covering of the cord.
In a 13A (BS 1363) fused plug, fit a
13A fuse. Tighten the plug cover
securely.
If you are in any doubt, consult a
qualified electrician.
IMPORTANT: If the supply cord is
damaged, it must be replaced by the
manufacturer, service agent or similar
qualified person in order to avoid a
hazard. The supply cord may become
warm when the appliance is in use.
WARNING: This applianc
must b arth d.
Loca ion
• More than 100mm from any wall.
• On a flat level surface.
• This appliance is for indoor use
only.
Using
IMPORTANT: Always put water in
the urn before switching on.
1Lift the lid and fill the urn with the
desired amount of water.
• Do not fill above the ‘MAX’
capacity mark.
WARNING If the urn is over
filled there is a risk that boiling water
may be ejected.
• Under filling will cause the boil dry
cut-out to operate (and may
shorten the life of the element).
The urn is not suitable for boiling
liquids other than water or for boiling
water containing small solid particles.
If the water is being boiled for tea
making, it is best to make the tea in
another container. However, if it is
necessary to make the tea in the urn it
should be suspended clear of the urn
bottom and heating elements in a
muslin bag. If it is intended to boil
large items such as puddings or hams
in the urn, they should be suspended
clear of the urn bottom and heating
element.
Thermos a con rol
2The green light will glow to show
power is connected to the urn.
3Turn the control knob to 6.
4When the water boils, turn the
control knob to approximately
setting 5 to keep it simmering. An
exact setting will be found by
experience.
To maintain the water at any
other temperature, set the control
knob to approximately one of the
following positions:
Approx temp nob setting
37ºC (99ºF) 1
55ºC (131ºF) 2
68ºC (155ºF) 3
82ºC (180ºF) 4
100ºC (212ºF) 5/6
If it is necessary to keep the water
at an exact temperature, use a
thermometer to check this. Stir the
water before taking the temperature
and when the desired temperature has
been reached, turn the control knob
slowly to the left until a click from the
thermostat is heard. The thermostat
will cycle on and off to maintain the
temperature.
Serving
5 Saf ty tap The tap is locked or
unlocked by twisting it so that the
closed or opened padlock symbol
is lined up with the white dot on
the tap body.
6 G n ral op ration There are
two open positions, one self-
holding so that the tap remains
open, and the other self-closing so
that the tap closes as soon as the
lever is released. To change the
tap position, turn the tap lever
through 180º.
7Open the tap by depressing the
tap lever into the horizontal
position.
8Close the tap by returning the
lever to a vertical position.
Af er use
9Switch off to 0 and disconnect
from the mains supply.
Water may be left in the urn when
it is not in use for short periods, but to
maintain a supply of fresh water, it
should be emptied periodically and
cleaned out.
WARNING: Only move when
disconnected and empty.
Pro ec ive cu -ou
The heating element is fitted with
a thermal cut-out which protects the
urn from damage if it is allowed to boil
dry or is switched on without water. If
this happens, allow the urn to cool
down then press the reset button
situated under the base. If this
happens, allow the urn to cool, drain
the water then press the reset button,
situated on the base.
In order to ensure correct
2
Impor an
safeguards
• To avoid being scalded when the
urn is operating or has just been
switched off keep hands away
from any steam from the lid. Be
particularly careful not to touch
hot surfaces when opening the lid
or filling.
•Do not use the appliance if it has
malfunctioned or has been
damaged in any way.
• Do not dismantle any part of the
urn. Responsibility cannot be
accepted if this instruction is
ignored.
• Do not place the urn on or near
hot surfaces.
• Do not use accessories or
attachments which are not
recommended or sold by Burco
Appliances as they can cause
hazards.
• This appliance must only be used
for heating water.
• Always switch off and disconnect
the urn from the mains supply
when not in use or when cleaning.
• To prevent any risk of
electrocution do not immerse the
urn in water or any other liquid
when cleaning and do not allow
any water or liquid to come into
contact with any of the electrical
connections or controls.
• Do not allow the cord to hang
over the edge of the work surface,
to touch wet or hot surfaces or
become twisted.
• The urn should not be lifted whilst
connected to the mains.
• The urn should not be carried
whilst it contains water.
• Maintenance other than cleaning
should be performed by the
manufacturer while this product is
within guarantee (contact our
service help line) or otherwise by a
qualified service engineer.
• This appliance is not suitable for
installations in an area where a
water jet could be used.
• This appliance is not to be
intended for use by persons
(including children) with reduced
physical, sensory or mental
capabilities or lack of experience
and knowledge unless they have
been given supervision or
instruction concerning use of the
appliance by a person responsible
for their safety. Children should be
supervised to ensure that they do
not play with the appliance.
• This appliance is not suitable for
installation in an area where a
water jet could be used.
•This appliance must not be
cleaned by a water jet.
• This appliance is only to be
installed in locations where its use
and maintenance is restricted to
trained personnel.
• For correct operation this
appliance should be operated in
an ambient temperature between
22-28 °C.
Ins alla ion
Prepara ion
1Remove any plastic film from the
urn and wipe over all surfaces with
a damp cloth.
2Check that the voltage shown on
the rating plate is suitable for your
supply.
3Before general use it is
recommended that the urn is
boiled twice discarding the water
each time.
Fi ing a plug
The mains lead of this urn will
already be fitted with a BS1363 13A
plug. In the event of replacing a fuse,
a 13 amp fuse approved by ASTA or
BSI must be used.
If the plug is not suitable for your
socket then the plug must be cut off
and disposed of safely.
An appropriate plug should be
fitted as follows:
IMPORTANT: The wires in the
mains lead are coloured in accordance
with the following code:
Green-and-Yellow – Earth
Blue – Neutral
Brown – Live
The wire, which is coloured green-
and-yellow, must be connected to the
terminal in the plug which is marked
with the letter E or the earth symbol
#or coloured green or green-and-
yellow.
The wire, which is coloured blue,
must be connected to the terminal
which is marked with the letter N or
coloured black or blue.
The wire, which is coloured brown,
must be connected to the terminal
which is marked with the letter L or
coloured red or brown.
Make sure that the connections
are tight and that there are no loose
strands of wire and no insulation
CUT HERE & DETACH
CP149435MUK-62091Rev5-Cygnet:8749 Bu co boile s 4pp 15/10/08 10:37 Page 4