CYTON CX1 User manual

Smart Network Camera
User Manual
Model:CX1

Contents
Contents.............................................................................................. 
Alarm ................................................................................................... 
Unpacking inspection..................................................................... 
1 Product Introduction................................................................. 01
1.1 Product Structure .......................................................02
1.2 Product Specification ..................................................03
1.3 Interface...........................................................................04
1.4 Speed Dome Camera ..................................................05
2 Installation guide ........................................................................ 07
3 Device connection ......................................................................10
4 Common functions .....................................................................18
After-sale service .........................................................................22
Warranty card ................................................................................. 23


Alarm
Users should be careful when seeing accessories with
Dangerous Voltage, as this can cause serious voltage
accidents.
To avoid electric shock, do not remove or plug the
power supply with wet hands.
To prevent fire or electric shock accidents, do not
place this product in wet or rain prone places.
To prevent electric shock accidents, do not repair this
product while the power is on.
Attention:
If this product needs to repair, please contact
after-sales personnel.
The operating temperature range of the equipm-
ent is -20℃~+60℃, and the relative humidity are less than
85%.
Do not operate this product beyond the temperature,
humidity, or power range described in the specifications.
To prevent a fire accident caused by a short circuit, do
not use a power supply that does not meet the
recommended standards.

To protect your rights and interests, please read this
manual carefully before installing and using this product.


Unpacking inspection
After unpacking, please check the number of products in the
box according to the product list. If relevant items are
missing, please contact the distributor immediately to replace
the new products. Table 1-1 shows the product list:
Num
Name Amout Units
Table 1-1 Product list
1
2
3
4
5
Camera
Charging cable
Screw
1
1
1
1
1
Bracket
User guide






1 Product Introduction
This product is a network intelligent network camera
independently developed by the company, which is mainly used
for security monitoring in family private domains or public
places.
This product is equipped with a light sensor, which can
automatically turn on the lighting mode at night, and can have
clear picture quality of the day and night.
This product and cloud storage service (required for paying
services) are used in conjunction, which can perform AI
intelligent classification. It can be recognized not to identify
human nature, parcels, vehicles, and adjust the camera
rotation angle with the mobile objects in the screen.
When the camera detects suspicious goals, the cloud service
can send the early warning information to the mobile app in
time to remind the owner to prevent it in advance to better
protect your safety.
01

1.1 Product Structure
Bracket
Airframe
The product consists of two parts, the support and the
fuselage from top to bottom, as shown in Figure 2-1:
Figure 2-1 Camera structure
02

1.2 Product Specification
Num
Product name1
3
2
4
6
5
7
8
9
10
11
Category
110mm×125mm×115mm
Product model CX1
450g
Smart network camera
1/3 "COMS, 300 pixels
F2.1
D: 93.6°,H: 79.5°,V: 43.1°
H.264/H.265
Cloud storage, local
Micro SD and mobile
phone memory
TCP/IP、UDP/IP、
DHCP、RTMP、MUTP
Size（L×W×H）
Wight
Camera
module
Focal length
Aperture
Visual angle
Compressing
Method
Storage
Video
Protocols Supports
Wireless Network
Parameter Other
2.4GHz WIFI
(IEEE 802.11 b/g/n
03
)

12
13
14
15
5V±5%，1.5A
Input power supply
Operating
temperature
Storage
temperature
AI intelligent
classification
-10 ℃~ 45℃
-20 ℃~ 60℃
Humanoid detection,
vehicle detection,
package detection,
motion detection
04
Num Category Parameter Other

Reset
interface
SD card
interface
Waterproof
Type-C interface
The body of the intelligent network camera has three ports, as
shown in Figure 2-2:
1.3 Interface Description
Figure 2-2 Camera ports
05

Photosensitive
sensor
Status light
Fill light source
Dierent colors of the indicator indicate
dierent working states.
Fill light Source
Status Light
Photosensitive
Sensor
When the light sensor detects poor light, it
automatically turns on the fill light to provide
a light source for the camera.
When the sensor detects poor light, it triggers
the fill light switch.
Figure2-3 structure
1.4 Speed Dome Camera
06

2 Installation Guide
Figure 2-4 Wall-mounted installation
Figure 2-6 Installing the rod
Figure 2-5 Ceiling installation
󾗞󾗡󾗟
There are two installation methods of this product:
wall-mounted installation and suspended ceiling installation.
As shown in Figure 2-4, 2-5 and 2-6:
07

󾗜󾗤
The installation steps are as follows:
3. Tighten expansion screws. Use a small hammer to hammer
the expansion screws into the hole just made.
1. Put on locator stickers. Attach the locator sticker to the
ideal mounting position.
Figure 2-7 locator stickers
Figure 2-8 Punching the holes
Figure 2-9 Tightening expansion screws
2. Punch a hole. Use an electric drill to drill holes in the
cross positions marked on the location stickers.

󾗜󾗥
4. Secure camera. Use a screwdriver and screws to secure
the camera to the wall, as shown in Figure 2-10.
Figure 2-10 Securing the camera

Figure3-1 Eseecloud
Figure 3-3 Registering an account
Figure 3-2 Downloading the QR code
2. Register "Eseecloud" account. After the installation is
completed, open the App and complete the account
registration according to the prompts.
1. Download "Eseecloud" App. Search for it in the app store or
scan the QR code to download it "Easy to see Cloud" App, as
shown in Figure 3-1 and 3-2:
� Device connection
10

Figure 3-5 Resetting the device
Figure 3-4 Login account
Reset
4. Power on the camera. After you hear an announcement,
proceed to the next step. If you do not hear an announcement,
hold down the reset button using the card pin for 3 to 5
seconds to reset the device.
3. Log in to your account. Open the "Eseecloud", enter the
account name and password, and log in to the account (the
software supports third-party account login, such as wechat
and Apple accounts).
11

This product provides four ways to add a camera, including
camera scanning QR code, camera hot spot connection, manual
input device ID and LAN scanning.

5. Add a camera (this addition takes "Camera scanning QR
code adding" as an example). Click "Add Camera" on the main
page or click the Add symbol in the upper right corner (as
shown below). By default, the system uses Camera Scan QR
code Add. If you want to add by other methods, select Other
methods at the bottom of the QR code scan page.
Figure 3-6 Adding a camera
12

Figure 3-7 Other adding methods
7. Scan the QR code of the fuselage. Scan the QR code on the
camera body with your mobile phone and wait for the camera
status check to be completed.
6. Check the camera status. Observe whether the indicator is
blinking. If it is blinking, click Next.
13

Figure 3-8 Scanning the device QR code
8. Connect to WiFi. Select the WiFi name that the camera needs
to connect to, enter the correct password, and click Next.
14

Figure 3-9 Add network
9. Scan the QR code on your phone. Use the camera to scan the
QR code of the mobile phone according to the guidance
diagram. After hearing the prompt tone, click the button below
to enter the device configuration state.
15

Figure 3-10 Scanning the QR code of the mobile phone with the camera
16