D'KOCINA BCPBT60 User manual

2
Cooker hood
Instruction Manual
Models:
BCPBT60/90
BCPBT63GL60
BCPBT93GL90
BCPAWGB53C60

3
CONTENT
1……………………………………….Notice
2……………………………………….Feature
3………………………………………..Installation
4………………………………………..Notice of installation
5………………………………………..Safety Warning
6…………………………………………Use
7…………………………………………Maintenance
8…………………………………………..Warranty card

4
1
NOTICE
1. Thank you for choosing our cooker hood. Please read the
instruction manual carefully before use.
2. The installation work must be undertaken by a qualified and
competent fitter.
3. The manufacturer disclaims all liability for any damage or
injury caused as a result of not following instructions for
installation contained in the following text.
The cooker hood is used on 110V, 60Hz.

5
2
(2)FEATURE
1. The cooker hood uses high quality materials, and is made with a
streamlined design.
2. Equipped with a large power low noise electric motor and
centrifugal leaf, it produces strong suction, low noise, non stick
grease filter and easy to clean.
3. With the isolated low voltage circuit board control, 12vAC
input, the lights are therefore safer.
4. Special wind tunnel construction and oil collector design, free
dirt will be absorbed in a second.

6
3
(3). Installation
If the model without Glass:
3.1 The cooker hood should be placed at a
distance of 65-75cm (26-30inch) from the
cooking surface for the best effect. See Pic
1.
3.2 Install the hook on a suitable place once
the installation height is fixed, and keep it in
line. The fixed position of the inside
chimney bracket is the place of chimney.
3.3 Fix the outside chimney bracket on the
outside chimney, and be sure that the inside
chimney can be adjusted the height in it freely as well as fixing the
extensible tube. Afterwards, install the extensible tube and chimney on
the cooker hood. See Pic 3.
3.4Put the cooker hood on the hook. See Pic 4.
3.5 Adjust the height of the inside chimney to the position of the inside
chimney bracket and fix on it by screw, after adjusting the position, fix
the body with safety screw. See Pic 5.

7
Note: The two safety vents are positioned on the back casing, with
diameter of 6mm.
If the model with Glass:
3.1 The cooker hood should be placed at a
distance of 65-75cm (26-30inch) from the
cooking surface for the best effect. See Pic 1.
3.2 Install the hook on a suitable place once the
installation height is fixed, and keep it in line.
The fixed position of the inside chimney
bracket is the place of chimney.
3.3 Fix the extensible pipe according to the lead
direction and way, and then put the cooker
hood on the hook. See pic 3.
3.4Put the glass according to the lead direction and way on the cooker
hood, and then use the screws to fix the glass, also lead the extensible
pipe outside of the room, meanwhile adjust the height of the inside
chimney to the position of the inside chimney bracket and fix on it by
screw , here should be sure the inside chimney can be flexed freely. See
Pic 4.

8
3.5 Put the two chimneys together onto the cooker hood body, meanwhile
adjust the height of the inside chimney into the suitable height, and fix the
inside chimney to the inside chimney bracket by screw. Finally, fix the
body with safety screw. See Pic 5.
Note: The two safety vents are positioned on the back casing, with
diameter of 6mm
(4) NOTICE OF INSTALLATION
1. Before installation, please ensure the area is clean to avoid
suction of the remaining bits of broken wood and dust.
2. It cannot share the same air ventilation tube with other
appliance such as gas tube, warmer tube, and hot wind tube.
3. The bending of ventilation tube should be≥120°, parallel or
above the start point and should be connected to the external
wall.
4. After installation, make sure that the extractor is level to avoid
grease collection at one end.

9
(5) SAFETY WARNING
Keep your children from using the cooker hood.
Your cooker hood is for domestic use only, not suitable for barbecue, roast shop
and other commercial use.
Any installation work must be carried out by a qualified electrician or competent
person.
The cooker hood and its filter mesh should be cleaned regularly in order to keep
in good working order.
Before cleaning, always ensure that you have switched your cooker hood off.
Clean the cooker hood according to the instruction manual and keep the cooker
hood from the danger of burning.
No fire for drying your cooker hood.
If there is any fault with your cooker hood, please call the service department
appointed by agent for servicing.
Please keep the room draughty when your cooker hood and gas hob are working.
Do not exhaust the gas from cooker hood through the same heated flue which is

10
for the gas from gas hob and other kitchen appliances.
Before installation and usage, read all the instructions and make sure that the
voltage (V) and the frequency (Hz) indicated on your cooker hood are exactly the
same as the voltage (V) and the frequency (Hz) in your home.
In order to get the most out of your cooker hood, please read the instruction
manual before installing & using, and keep it in a safe place.
Ensure that you could get our guarantee for your cooker hood, please provide the
warranty card and purchase receipt, or the guarantee will not be offered.
（6）Speed adjustment .See pictures
Electronic Button
1. Push the low button, the indicating light 1 on, and the motor
runs at low speed. Push it again and the motor will stop.
2. Push the middle button, the indicating light 2 on, and the
motor runs at mid speed. Push it again and the motor will stop
3. Push the high button, the indicating light 3 on, and motor runs
on high speed. Push it again and the motor will stop
4. Push the light button; the indicating light 4 on, and the two
lighting lamps will come on. Push it again and the lamps will
turn off.

11
Push button
1. Push stop button, and the motor will stop.
2. Push the Low button, and the motor runs at low speed.
3. Push the high button, and the motor runs at mid speed.
4. Push the High button, and the motor runs at high speed.
5. Push the light button and the two lights will come on. Push it
again and the light will turn off.

12
pic6C
Low
Mid
High
Light
Stop
pic6C
Low
Mid
High
Light
Stop
pic6C
Low
Mid
High
Light
Stop
LCD Electronic button
Pic 7

13
1. Plug the hood; LCD will display 24-hour system with blue
backlight. Backlight will be extinguished after 30 seconds
without any operation.
2. Press “ ” button once; lights will be on and LCD will show
“ ”. Press “ ” button again; lights will be off and “ ” on
LCD will disappear.
3. Press “ ” button once; the hood works at LOW speed and LCD
will show “ ” and “ ” button will be on. Press “ ” button
again; the hood works at MEDIUM speed. Press “ ” button one
more time; the hood works at HIGH speed. Press “ ” button
again; the hood works at LOW speed again and it repeat. While
pressing “ ” button; the “ ” button is always on. If you want
to stop the hood now; press the “ ” button once.
4. When the hood is not working; press “ ” button once. The hood
will work at the speed it works last time and LCD will show
“ ”. Press “ ” button again; the hood stop working and “ ”
will disappear from LCD.
5. When both “ ” button and “ ” button don’t work; “ ”
button is used for time-setting. Press “ ” button for 2 to 3
seconds; will be shown on LCD and flashes; which
represents hour. Press “ ” button once the number adds by 01.
Continue pressing “ ” button; it will display from 13;14…until
23. When LCD shows 23; it doesn’t work by pressing “ ”
button. Press “ ” button once; the number reduces by 01. When
LCD shows 00; it doesn’t work by pressing “ ” button. After
setting hour; you can start setting minute by pressing “ ” button
again. on LCD flashes; which represents minutes. Press “ ”
button once the number adds by 01. Continue pressing “ ”
button; it will display from 01;02…until 59. When LCD shows
59; it doesn’t work by pressing “ ” button. Press “ ” button

14
once; the number reduces by 01. When LCD shows 00; it doesn’t
work by pressing “ ” button. After setting hour and minute;
press “ ” to confirm.
When “ ” button doesn’t work; “ ” button is used for delay timer
function. Delay timer function allows you to set the hoods
automatically power off according to the delay timer you set from 1
minute to 60 minutes. Press “ ” button once; it enters for delay
timer setting and LCD shows . Press “ ” button once the
number adds by 01. Continue pressing “ ” button; it will display
from ; ; …until Press “ ”
button once; the number reduces by 01. After setting delay timer you
want; press “ ” button to confirm. If you set delay timer as 05:00;
the LCD display will show from 05:00; 04:59…until 00:01 00:00.
When LCD shows 00:00; the hood will automatically power off and
LCD display will only show 24-hour system with blue backlight.
After 30 seconds without operation; blue backlight will disappear.
But please note the Lamp is not under control of delay timer. Next
time; if you want to use delay timer function and you press “ ”
button without any change on time. The hood will automatically
count time down from your previous setting after 5 seconds.
LCD Touch control
Pic 8

15
1. Power on: Switch on the power supply, and the backlight is lit,
displaying “24-hour system”. The output is then blocked up,and
the soot machine enters standby status. The backlight disappear
automatically 30 seconds later under the condition of none
operation.
2. Press “Indicator” key: Press the indicator key once, the indicator
is lit, and on the LCD screen is lit. Press it for a second time,
of the indicator and the LCD screen will distinguish and it
will be repeated again and again.
3. Power on position and increase key , the motor is provided
with three positions, i.e. low, medium and high.
1. Press key once, the is displayed on the display screen,
and the motor starts operation. The is the low position
(power on position.)
2. Press key once more at the low position, the is
displayed on the display screen, and the is the medium
position.
3. Press key once more at the medium position, the
is displayed on the display screen, and the is the
high position.
4. Go on pressing key at the high position, the is
still displayed on the display screen, and the motor works
normally. It is still at high position at this time.
4. Power on position and decrease key “ ”
1. Press “ ” key once, the motor is adjusted to a lower
position, and the LCD screen displays that position in the
meantime; If it is decreased continuously to none position,
then, it is the power off position (namely, the motor stops
operation.)
5. Timer key “”:
1. The timer key is the timer setting key if the timer key
doesn’t work at both the position and indicator.
①Long press timer key for 2-3 seconds, time segment
, and the first two hour bit segment flash, use
key for the digit increase, and use key for the digit
decrease. Namely: The variable is 01 each time it is
pressed; the hour segment is with the largest digit of 23.

16
If it exceeds 23, key is null and void. If it is equal to
00, then, the key is null and void.
②Press the timer key for the 2nd time , time segment
, and the last two minute bit segment flash, use
key for the digit increase, and use key for the digit
decrease. Namely: The variable is 01 each time it is
pressed; the minute segment is with the largest digit of
59. If it exceeds 59, key is null and void. If it is equal
to 00, then, the key is null and void.
③Press the timer key for the 3rd time, and it is the time
setting exit and confirm key.
④Long press timer key for 2-3 seconds under this
operation mode, and it is for the hour setting; Press it
for the 2nd time: Setting for the minute; Press it for the
3rd time: For the time setting exit and confirm, and it
will be repeated again and again (if the 1st time pressing
doesn't exceed 2 seconds, then it can't run this operating
procedure.)
2. The timer key is the timer if the timer key works at either
the position or the indicator.
①It is provided with three kinds of time segment, and
they are 5min/15min/30min/timer cancel in sequence,
and the 1st time is 5min, the 2nd time is 15min, the 3rd
time is 30min, the 4th time is timer cancel, the 5th time is
5min, and the 6th time is 15min …., and it will be
repeated again and again.
②Example: Let the setting time be 15min, the display is
00:15, 00:14, …00:1, with 0:00 displays per minute,
and once “00: 00” appears, the motor position and the
indicator power supply will be cut off automatically,
(the display screen displays “24-hour system”, the
output is blocked up, and the soot machine enters
standby status, and the backlight will be put out
automatically 30 seconds later.)
③Time segment change over, 5 seconds later, it starts to
decrease gradually (example: 15min is changed over to
30min, with a delay of 5 seconds, and 00: 30 on the
display screen starts to decrease gradually).

17
(7) MAINTENANCE
7.1 The cleaning of the carbon grease filter mesh
The filter mesh is made of high-density stainless steel. Please do not
use the corrosive detergent on it. Keeping this filter clean will keep
the appliance running correctly. Please strictly follow the guidelines
below.

18
Method 1: Put the mesh into 40-50 c clean water, pour on detergent,
and soak for 2-3 mins. Wear gloves and clean with a soft brush.
Please do not apply too much pressure, as the mesh is delicate and
will damage easy.
Method 2: If instructed to do so, it can be put into a dishwasher, set
the temperature at around 60 degrees.
7.2 Notice of cleaning cooker hood
A. To protect the main body from corrosion over a long period of
time, the cooker hood should be cleaned with hot water plus
non corrosive detergent every two months.
B. Please do not use abrasive detergent for it will damage the
body.
C. Keep the motor and other spare parts free from water, as this
will cause damage to the appliance.
D. Before cleaning the appliance please remember to cut off
power
E. The carbon filter shouldn’t be exposed to heat.
F. Please don’t tear open the fixed bar around the carbon filter
G. If the plug or cord is damaged, please replace it with special
soft cord. 10
8.Abnormity and Solution
Fault
Cause
Solution
Light on, but motor
The leaf blocked
Get rid of the blocking
The capacitor damaged
Replace capacitor

19
does not work
The motor jammed bearing
damaged
Replace motor
The internal with of motor off or
a bad smell from the motor
Replace motor
Light does not work,
motor does not work
Beside the above mentioned, check the following:
Light damaged
Replace lights
Power cord looses
Connect the wires as per
the electric diagram
Oil leakage
One way valve and the air
ventilation entrance are not
tightly sealed
Take down the one way
valve and seal with glue
Leakage from the connection
of U-shaped section and
cover
Take U-shaped section
down and seal with soap
or paint
Shake of the body
The leaf damaged and causes
shaking
Replace the leaf
The motor is not tightly
hanged
Lock the motor tightly
The body is not tightly
hanged
Fixed the body tightly
Insufficient suction
The distance between the
body and the gas top too long
Readjust the distance
Too much ventilation from
open doors or windows
Choose a new place and
resemble the machine
The machine inclines
The fixing screw not tight
enough
Tighten the hanging
screw and make it
horizontal
The hanging screw not tight
enough
Tighten the hanging
screw and make it
horizontal
11