D-Link Express EtherNetwork DI-604+ User manual

1. If you purchased this router to share your high-speed Internet connection with other
computers, you must have either an Ethernet-based Cable or a DSL modem with
an established Internet account from an Internet Service Provider (ISP).
2. It’s best to use the same computer that is connected to your modem for configuring
the DI-604+ router. The DI-604+ Broadband Router acts as a DHCP server and
will assign all the necessary IP address information on your network. See
Appendix at the end of this Quick Installation Guide or the Manual on the
CD-ROM for setting each network adapter to automatically obtain an IP
address.
Check Your Package Contents
These are the items included with your DI-604+ purchase:
If any of the above items are missing, please contact your reseller.
©2005 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective
holders. Software and specifications subject to change without notice.
This product can be set up using any current
web browser, i.e., Internet Explorer 6x,
Netscape Navigator 7x.
DI-604+
Express EtherNetwork™
Broadband Router
• DI-604+ Broadband Router
• CD-ROM (containing Manual and Warranty)
• Ethernet (CAT5 UTP/Straight-Through) Cable
• 5V DC, 1.2 A Power Adapter
Using a powe
r
supply with a
different voltage rating
will damage and void
the warranty for this
product.
Before You Begin

2
Connecting The DI-604+ Broadband
Router To Your Network
A. First, connect the power adapter to the receptor at the back panel of the DI-
604+ and then plug the other end of the power adapter to a wall outlet or power
strip. The Power LED will turn ON to indicate proper operation.
B. Insert one end of an Ethernet cable to the WAN port on the back panel of the
DI-604+ and the other end to the Ethernet port located on your Cable or DSL
modem. The WAN LED light will illuminate to indicate proper connection.
C. Insert one end of an Ethernet cable to LAN port 1 on the back panel of the DI-
604+ and the other end to an available Ethernet port on the network adapter in the
computer you will use to configure the DI-604+. The LED light for LAN Port 1 will
illuminate to indicate proper connection. (Note: Some computers already have
network adapters pre-installed.)
Restart Your Computer
B. WAN Port
This is the
connection for the
Ethernet Cable to
Ethernet Port on the
Cable or DSL
Modem.
A.Receptor for
Power Ada
p
te
r
Reset Button
Pressing this button
restores the router
to its original factory
default settings.
C.LAN Ports
These are the
connections for
Ethernet cables to
your Ethernet-
enabled com
p
uters

3
Connecting Additional Devices to the
DI-604+ Broadband Router
Using additional Ethernet (CAT5 UTP/Straight-Through) cables, connect your
Ethernet-equipped computer(s) to one of the 3 remaining Ethernet LAN ports on
the back panel of the DI-604+.
When you have completed the steps in this Quick Installation Guide, your
connected network should look similar to this:
LAN Port LEDs.
Each of the LAN ports on the back
of the DI-604+ have a corresponding
LED light on the front panel of the
unit. When a proper connection has
been made to a computer that is ON,
the LED on the front panel should
illuminate.
DI-604+
Broadband Router
Computers connected
to the LAN Ports
Cable or DSL
Modem connected
to the WAN
p
ort.

4
Using the DWizard
The DI-604+ offers two easy-to-use methods to set up and manage the Router. The
first, the D-Link Click’n Connect DWizard, is a stand-alone configuration utility located
on the CD-ROM that came with your DI-604+. This method is described briefly below.
The second method uses a Setup Wizard that is part of the Router firmware. Please
see section 5 for detailed instructions on how to use this wizard.
To launch the DWizard, simply place the CD-ROM that came with the DI-604+ in your
computer’s CD drive. The following window will open:
Now, click on the Quick Installation Start icon located in the lower right side of the
window. The following window will open:

5
Click Next on the window above and follow the on-screen prompts to Connect the
device to the computer, Connect the device to the Internet, Check device connectivity,
Set your ISP, Set wireless configuration, Check your Internet connection status, ISP
configuration, etc.
When you have completed the Router configuration, click the Exit button on the final
Congratulations window displayed below.
For additional information on how to set up and manage the Router, please see the
Appendix at the end of this QIG or consult your DI-604+ User’s Guide.

6
Using The Setup Wizard
The logon pop-up screen will appear.
Once you have logged in, the Home screen will appear.
Open your Web
browser and type
“http://192.168.0.1” into
the URL address box.
Then press the Enter or
Return key.
Click OK
Click Run Wizard
Type “admin” for
the username and
leave the password
field blank.

7
You will see the following screens.
Step 1 - Set up your new password.You have the option to establish a password.
Step 2 - Choose your time zone.
Click Next
Click Next
Click Next

8
The Setup Wizard (continued)
Select the type of Internet connection for your router.
If you selected Dynamic IP Address, this screen will appear:
Click Next
If you are unsure of which setting to
select, please contact your Internet
Service Provider.
What is a MAC address? Each
network adapter has a discrete
Media Access Control (MAC)
address. Note that some computers
and peripherals may already include
built-in network adapters.
Click Next
“Clone MAC Address”
button to automatically
copy the MAC address
of the network adapter in
your computer. You can
also manually type in the
MAC address.
Select one of
these settings

9
If your ISP requires a Static IP Address, and this option is selected, then this screen
will appear:
If your ISP uses PPPoE (Point-to-Point Protocol over Ethernet) and this option is
selected, then this screen will appear:
Click Next
Please be sure to remove any
existing PPPoE client software
installed on your computers.
Enter the IP address
information originally
provided to you by your
ISP. You will need to
complete all the required
fields.
Enter in the username
and password provided
to you by your ISP and
retype that same
password to verify it.
Click Next

10
If your ISP uses PPTP and this option is selected, then this screen will appear.
If your ISP uses L2PT and this option is selected, then this screen will appear.
Enter the IP address
information originally
provided to you by your
ISP.
Click Next
Enter the IP address
information originally
provided to you by your
ISP.
Click Next