D-Link Express Ethernetwork DI-707P User manual

1
Before you begin…
Make sure that any existing Firewall Software/Devices are disabled and/or
shutdown before beginning installation of your new D-Link DI-707P
Broadband Router.
•DI-707P Broadband Router with Print Server
•Quick Install Guide
•Power Adapter
•CAT-5 UTP Cable
•CD-ROM(Print Server Software, Quick Install Guide, User’s
Manual)
When you have completed the steps in this installation guide, your connected
network may look something like this:
Connecting the DI
-
707P
Ethernet Broadband Router to
your network
Contents of Package

2
First, plug in the power supply as
shown. Plug the other end of the
power supply into the power source.
Flip the POWER toggle switch to the
ON position.
(During a self-test phase, the
indicator lights will flash briefly. At
the end of the self-test, the M1
indicator light will flash continuously
to indicate normal operation.)
Next, connect the WANport to
the Cable or DSL modem using
an
Ethernet cable.
Using CAT5 UTP cable,
connect each computer that is
equipped with an Ethernet
adapter to one of the four
Ethernet LAN ports on the DI-
707P.
The LED for the specific Local
Ethernet Port will light up to
indicate connection.
Connecting the DI
-
707P
Ethernet Broadband Router to your
network

3
Make sure that TCP/IP protocol has been
installed in your computer.
Next, set the TCP/IP protocol to
“Obtain an IP Address automatically”
by doing the following:
•Go to Start>Settings
•Select “Control Panel”
•Double -click the “Network” icon
•Select the TCP/IP line that includes the
name of your network adapter card,
under the “Configuration” tab in the
“Network” window
•Click on “Properties” in this window
•The window at the right will appear
•Select the “IP Address”tab as shown
•Choose “Obtain an IP
address automatically”
•Click “OK”
Note: For information on setting the IP address of your computer manually
(a static IP address,) please see Appendix A in this guide.
Next, find your IP Address by doing the following:
For Windows 98/ME:
•Go to Start>Run
•Type in “winipcfg”
•Click “OK”
For Windows 2000:
•Go to Start>Run
•Type “cmd”
•When the prompt
appears, type
“ipconfig”
•Hit “Enter”
•The window displayed on the next page will appear
Checking the IP Address

4
•Use the “pull-down
menu” on this screen to
display the Ethernet
card that is installed in
your computer and
connected to the DI-
707P. The IP Address
(for the Ethernet
network adapter) that
appears in this window
must be between
192.168.0.2 and
192.168.0.254 in order
to configure
the DI-707P.
•If the IP Address is not in that range, please do the following:
Click on “Release All” and “Renew All” to obtain a “Dynamic IP Address”from
the DI-707P within the range of 192.168.0.100 to 192.168.0.199.
Note: Please disable any proxy server setting for the web browser.
Open the web browser, and type in the
DI-707P’s IP Address.
For example, type http://192.168.0.1 into
the “Location” or “Address” field.
Hit “Enter”
Configuring the DI-707P with
the Web browser
Checking the IP Address

5
Type “admin” in the “System Password” field.
Click on “Log in”
Click on “Setup”
Configuring the DI-707P with
the Web browser

6
Click “Change”
(Please see separate instructions below for DSL and Cable users.)
For DSL users:
Select “PPP over Ethernet” if you are using a PPPoE client to connect to
your DSL provider (contact your DSL provider if you are uncertain.)
Configuring the DI-707P with
the Web browser

7
For DSL users (continued):
Enter the PPPoE Account and Password that your ISP assigned to you.
Leave the password field blank if you do not want to change the password.
Input the PPPoE Service Name if your ISP requires it.
Set the Maximum Idle Time. (Entering a value of “0” will disable this feature.)
Click “Save.”
Restart the computer.
Configuring the DI-707P with
the Web browser

8
For Cable Users:
Select “Dynamic IP Address.”
Click “Save.”
Enter the “Host Name” given to you by your cable provider
(for example, “@Home.”)
For information on configuring a back-up dial-up modem, please see the
“Configuration” section of your User’s Manual.
Click “Save”after you have input the information.
Restart the computer.
Configuring the DI-707P with
the Web browser

9
To check the connection, open the web browser and go to your favorite website.
If you are unable to browse, please do the following:
1. Refer to Appendix B to check your connection.
2. Use “Help” on the Main Menu.
3. Refer to the troubleshooting section in the user’s manual.
Your DI-707P Ethernet Broadband Router is now ready to use. Please proceed to the
“Print Server Installation” instructions that follow if you plan to use the Print
Server feature.
Checking the Connection
to the Internet

10
NOTE: Installing the Print Server software is only necessary if you plan to
use the Print Server function of the D-Link DI-707P. If you choose to use the print server
function, plug the printer cable from your printer into the printer port on the DI
-707P, if you
have not already done so.
Turn “ON” the computer. Insert the Print Server installation CD into the CD-ROM
drive. The following screen will appear. If the CD does not automatically run, then
click on “install.exe” on the CD.
Click on “Install Printer Software”
At the “Welcome” screen,
Click “Next”
Print Server Installation
(optional)