D-Link DIR-604 User manual

X
jsfmftt!O!261!Bddftt!Qpjou0Spvufs!

iD-Link DIR-604 User Manual
D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to
notify any person or organization of such revisions or changes.
Trademarks
D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the
United States or other countries. All other company or product names mentioned herein are trademarks or registered
trademarks of their respective companies.
Copyright © 2010 by D-Link Systems, Inc.
All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission
from D-Link Systems, Inc.
Preface

iiD-Link DIR-604 User Manual
Table of Contents
Preface...........................................................................i
Manual Revisions ..................................................... i
Trademarks .............................................................. i
Product Overview ........................................................ 1
Package Contents ...................................................1
System Requirements ............................................. 2
Features .................................................................. 3
Hardware Overview ................................................. 4
Connections ....................................................... 4
Top View ............................................................ 5
Switching Between WAN Mode/3G Router
Mode .................................................................. 6
Installation ....................................................................7
Before you Begin ..................................................... 7
Wireless Installation Considerations ........................ 8
Network Diagram ....................................................9
WAN Connection ............................................... 9
Network Diagram ..................................................10
3G Connection ................................................. 10
Connect to Cable/DSL/Satellite Modem ................ 11
Connect to a 3G Internet Service .......................... 13
Connect to Another Router .................................... 14
Conguration ............................................................. 16
Web-based Conguration Utility ............................ 16
Internet Connection Setup Wizard (3G Mode) .17
Manual Conguration (3G Mode) .................... 20
3G Internet Connection ................................ 20
Internet Connection Setup Wizard (WAN
Mode) ...............................................................21
Manual Conguration (WAN Mode) ................. 28
Static IP Address .......................................... 29
Dynamic IP Address (DHCP) .......................30
PPPoE (Username/Password) .....................31
PPTP (Username/Password) .......................33
L2TP (Username/Password) ........................35
Russia PPTP (Dual Access) ........................37
Russia PPPoE (Dual Access) ...................... 39
Wireless Settings ............................................. 41
Manual Wireless Network Setup ..................42
Network Settings .............................................. 44
DHCP Server Settings .................................45
DHCP Reservation .......................................46
Virtual Server ...................................................47
Port Forwarding ............................................... 49
Application Rules .............................................50
QoS Engine ..................................................... 51
Network Filters ................................................. 52
Website Filters ................................................. 53
Firewall Settings .............................................. 54
Firewall Rules ............................................... 55
Advanced Wireless Settings ............................ 57
Wi-Fi Protected Setup ...................................... 58
Table of Contents

iiiD-Link DIR-604 User Manual
Table of Contents
Advanced Network Settings ............................. 59
UPnP ............................................................59
Internet Ping Block .......................................59
Internet Port Speed ......................................59
Multicast Streams ......................................... 59
Administrator Settings ...................................... 60
Change Password ........................................60
Remote Management ................................... 60
Time Settings ................................................... 61
E-mail Settings ................................................. 62
System Settings ............................................... 63
Update Firmware ............................................. 64
DDNS ............................................................... 65
System Check .................................................. 66
Schedules ........................................................67
Device Information ........................................... 68
Logs .................................................................69
Statistics .......................................................... 70
Internet Sessions .............................................71
Wireless ...........................................................72
Support ............................................................ 73
Wireless Security.......................................................74
What is WPA? .......................................................74
Wireless Connection Setup Wizard ....................... 75
Add Wireless Device with WPS Wizard ................. 78
Congure WPA-Personal (PSK) ............................ 79
Congure WPA-Enterprise (RADIUS) ................... 80
Connect to a Wireless Network ................................ 81
Using Windows Vista® ........................................... 81
Congure WPA/WPA2 ..................................... 82
Connect Using WCN 2.0 .................................. 84
Using Windows® XP ............................................... 85
Congure WPA-PSK ........................................ 86
Troubleshooting ........................................................ 88
Wireless Basics ......................................................... 92
What is Wireless? .................................................. 93
Tips ........................................................................ 95
Wireless Modes ..................................................... 96
Networking Basics .................................................... 97
Check your IP address ..........................................97
Statically Assign an IP address ............................. 98
Technical Specications........................................... 99

1D-Link DIR-604 User Manual
Section 1 - Product Overview
Product Overview
Note: Using a power supply with a different voltage rating than the one included with the DIR-604 will cause damage and void the warranty for this
product.
Package Contents
D-Link DIR-604 Wireless 11n Router
Power Adapter
Ethernet Cable
USB Cable

2D-Link DIR-604 User Manual
Section 1 - Product Overview
Network Requirements
• An Ethernet-based Cable or DSL modem
• IEEE 802.11n/g wireless clients
• 10/100 Ethernet
Web-based Conguration
Utility Requirements
Computer with the following:
• Windows®, Macintosh, or Linux-based operating
system
• An installed Ethernet adapter
Browser Requirements:
• Internet Explorer 6.0 or higher
• Mozilla 1.7.12 or higher
• Firefox 1.5 or higher
• Safari 1.0 or higher (with Java 1.3.1 or higher)
• Flock 0.7.14 or higher
• Opera 6.0 or higher
Windows® Users: Make sure you have the latest version
of Java installed. Visit www.java.com to download the
latest version.
System Requirements

3D-Link DIR-604 User Manual
Section 1 - Product Overview
• Faster Wireless Networking - The DIR-604 provides up to 300Mbps* wireless connection with other
802.11n wireless clients. This capability allows users to participate in real-time activities online, such as
video streaming, online gaming, and real-time audio.
• Compatible with 802.11g Devices - The DIR-604 is still fully compatible with the IEEE 802.11g standard,
so it can connect with existing 802.11g PCI, USB, and Cardbus adapters.
• Advanced Firewall Features - The Web-based user interface displays a number of advanced network
management features including:
• Content Filtering - Easily applied content ltering based on MAC Address, URL, and/or
Domain Name.
• Filter Scheduling - These lters can be scheduled to be active on certain days or for a
duration of hours or minutes.
• Secure Multiple/Concurrent Sessions - The DIR-604 can pass through VPN sessions. It
supports multiple and concurrent IPSec and PPTP sessions, so users behind the DIR-604
can securely access corporate networks.
• User-friendly Setup Wizard - Through its easy-to-use Web-based user interface, the DIR-604 lets you
control what information is accessible to those on the wireless network, whether from the Internet or from
your company’s server. Congure your router to your specic settings within minutes.
* Maximum wireless signal rate derived from IEEE Standard 802.11g and Final 802.11n specications. Actual data throughput will vary. Network conditions and
environmental factors, including volume of network trafc, building materials and construction, and network overhead, lower actual data throughput rate. Environmental
conditions will adversely affect wireless signal range.
Features

4D-Link DIR-604 User Manual
Section 1 - Product Overview
Power Receptor
Receptor for the supplied power
adapter.
WPS Button
Press the WPS button for 1 second to initiate the
WPS process. The LED indicator on the top of
the device will ash blue while a WPS connection
is being established. The button will light blue for
300 seconds if a successful WPS connection has
been made.
Ethernet Port
In Router mode, the Ethernet port is used to
connect to your WAN connection. In AP mode, the
Ethernet port is used to connect to your switch/
router. In Client mode, the Ethernet port is used to
connect your computer to a wireless network.
Hardware Overview
Connections

5D-Link DIR-604 User Manual
Section 1 - Product Overview
WLAN LED
A solid green light indicates that
the wireless segment is ready.
This LED blinks during wireless
data transmission.
Power LED
Lights orange during bootup. Lights
green when router has booted
up. A solid green light indicates
a proper connection to the power
supply. If the LED blinks orange
the system has failed.
Ethernet LED
A solid green light indicates that a link
has been established. This LED blinks
during data transmission.
Hardware Overview
Top View
WPS Button
Press the WPS button for 1 second to
initiate the WPS process. The button will
ash blue while a WPS connection is being
established. The button will light blue for 300
seconds if a successful WPS connection
has been made.

6D-Link DIR-604 User Manual
Section 1 - Product Overview
Hardware Overview
Switching Among AP, Client, and Router Mode
The DIR-604 features a hardware switch located on the bottom of the device that enables users to switch among Router
mode, Client mode, and AP mode.
When the DIR-604 is operating in AP mode, the device acts as a basic access point without any routing functionality.
When the DIR-604 is operating in Client mode, the PC that is connected to the device will use it as a wireless network
interface in order that it can connect to a wireless router or access point.
When the DIR-604 is operating in Router mode, WAN connectivity is achieved via the DIR-604’s Ethernet port. In this
mode LAN clients need to access the DIR-604 via the DIR-604’s wireless connection.
Mode Switch
Use to switch among AP mode,
Client mode, and Router mode.
Reset Button
Press the Reset button for 5
seconds to restore the Router to
its original factory default settings.

7D-Link DIR-604 User Manual
Section 2 - Installation
This section will walk you through the installation process. Placement of the Router is very important. Do not place the
Router in an enclosed area such as a closet, cabinet, or in the attic or garage. The D-Link wireless Router lets you
access your network using a wireless connection from virtually anywhere within the operating range of your wireless
network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the
wireless signals must pass through, may limit the range. Typical ranges vary depending on the types of materials and
background RF (radio frequency) noise in your home or business. The key to maximizing wireless range is to follow
these basic guidelines:
1. Keep the number of walls and ceilings between the D-Link Router and other network devices to a
minimum - each wall or ceiling can reduce your adapter’s range from 3-90 feet (1-30 meters.) Position
your devices so that the number of walls or ceilings is minimized.
2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (0.5 meters), at a
45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet
(14 meters) thick! Position devices so that the signal will travel straight through a wall or ceiling (instead
of at an angle) for better reception.
3. Building Materials make a difference. A solid metal door or aluminum studs may have a negative effect on
range. Try to position access points, wireless routers, and computers so that the signal passes through
drywall or open doorways. Materials and objects such as glass, steel, metal, walls with insulation, water
(sh tanks), mirrors, le cabinets, brick, and concrete will degrade your wireless signal.
4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that
generate RF noise.
5. If you are using 2.4GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and
home security systems), your wireless connection may degrade dramatically or drop completely. Make
sure your 2.4GHz phone base is as far away from your wireless devices as possible. The base transmits
a signal even if the phone in not in use.
Installation Considerations

8D-Link DIR-604 User Manual
Section 2 - Installation
Connection - AP Mode
To use the DIR-604 in AP Mode, follow the steps
below:
1. Ensure you have a broadband Internet connector,
such as a cable or DSL client line that connects
the Internet to your home or ofce.
2. Connect the cable properly or install the modem.
3. Connect the cable or modem with the broadband
router.
4. Connect the DIR-604’s Ethernet port to your
LAN.
5. Move the switch to wireless AP Mode.
6. Connect your PC or notebook to the DIR-604
using the PC or notebook’s wireless adapter.

9D-Link DIR-604 User Manual
Section 2 - Installation
Connection - Client Mode
To use the DIR-604 in Client Mode, follow the steps below:
1. Ensure you have a broadband Internet connector, such as a cable or DSL client line that connects the Internet to
your home or ofce.
2. Connect the cable properly or install the modem.
3. Connect the cable or modem with the broadband router.
4. Move the switch to Client Mode.
5. Connect your PC or notebook to the DIR-604 using the PC or notebook’s wireless adapter.

10D-Link DIR-604 User Manual
Section 2 - Installation
Connection - Router Mode
To use the DIR-604 in Router Mode, follow the steps below:
1. Ensure you have a broadband Internet connector, such
as a cable or DSL client line that connects the Internet to
your home or ofce.
2. Connect the cable properly or install the modem.
3. Connect the cable or modem with the broadband router.
4. Move the switch to Router Mode.
5. If you want to link with a computer on the Internet, please
install a wireless dongle on your computer.
6. Install the driver on your computer.

11D-Link DIR-604 User Manual
Section 2 - Installation
If your Internet connection is provided using a cable/DSL/satellite modem, carry out the following procedure before
connecting the router to a cable/DSL/satellite modem:
• Move the AP Mode/Client Mode/Router Mode switch on the DIR-604 so that it is in the Client Mode
position.
• Congure the wireless settings on the DIR-604 in Client Mode (see “Wireless Connection” on page 17 for
more information).
• After conguring the wireless settings, move the AP Mode/Client Mode/Router Mode switch so that it
is in the Router Mode position.
To connect to a cable/DSL/Satellite modem, please follow the steps below:
1. Place the Router in an open and central location. Do not plug the power adapter into the router.
2. Turn the power off on your modem. If there is no on/off switch, then unplug the modem’s power adapter. Shut down
your computer.
3. Unplug the Ethernet cable (that connects your computer to your modem) from your computer and place it into the
Ethernet port on the Router.
5. Turn on or plug in your modem. Wait for the modem to boot (about 30 seconds).
6. Plug the power adapter to the router and connect to an outlet or power strip. Wait about 50 seconds for the router
to boot.
7. Turn on your computer.
8. Use the wireless connection on your computer to connect to the Router, using the wireless settings you congured
Connect to Cable/DSL/Satellite Modem

12D-Link DIR-604 User Manual
Section 2 - Installation
previously.
9. Verify the link lights on the Router. The power light, Internet light, and the Wireless LAN light should be lit. If not,
make sure your computer, modem, and router are powered on and verify the cable connections are correct.
10. Skip to “Conguration” on page 15 to congure your router.

13D-Link DIR-604 User Manual
Section 2 - Installation
If you are connecting the D-Link Router to another router to use as a wireless access point and/or switch, you will have
to do the following before connecting the Router to your network:
• Move the AP Mode/Client Mode/Router Mode switch on the DIR-604 so that it is in the AP Mode position.
• Disable UPnP™
• Disable DHCP
• Change the LAN IP address to an available address on your network. The Ethernet port on the router
cannot accept a DHCP address from your other router.
To connect to another router, please follow the steps below:
1. Plug the power into the router. Connect one of your computers to the Ethernet port using an Ethernet cable. Make
sure your IP address on the computer is 192.168.0.xxx (where xxx is between 2 and 254). Please see the Networking
Basics section for more information. If you need to change the settings, write down your existing settings before
making any changes. In most cases, your computer should be set to receive an IP address automatically in which
case you will not have to do anything to your computer.
2. Open a web browser and enter http://192.168.0.1 and press Enter. When the login window appears, set the user
name to Admin and leave the password box empty. Click Log In to continue.
3. Click on Advanced and then click Advanced Network. Uncheck the Enable UPnP checkbox. Click Save Settings
to continue.
4. Click Setup and then click Network Settings. Uncheck the Enable DHCP Server server checkbox. Click Save
Settings to continue.
5. Under Router Settings, enter an available IP address and the subnet mask of your network. Click Save Settings to
save your settings. Use this new IP address to access the conguration utility of the router in the future. Close the
Connect to Another Router

14D-Link DIR-604 User Manual
Section 2 - Installation
browser and change your computer’s IP settings back to the original values as in Step 1.
6. Disconnect the Ethernet cable from the router and reconnect your computer to your network.
7. Connect an Ethernet cable into the Ethernet port of the router and connect it to your other router.
8. To congure your wireless network, open a Web browser and enter the IP address you assigned to the router. Refer
to the Conguration and Wireless Security sections for more information on setting up your wireless network.

15D-Link DIR-604 User Manual
Section 3 - Configuration
Configuration
This section will show you how to congure your new D-Link wireless Router using the Web-based conguration utility.
Web-based Configuration Utility for AP Mode
To access the conguration utility, open a Web-
browser such as Internet Explorer and enter the IP
address of the router (192.168.0.1).
Type Admin in the User Name eld and then enter
your password. Leave the password blank by default.
Click the Login button to log in to the Router.
If you get a Page Cannot be Displayed error, please
refer to the Troubleshooting section for assistance.

16D-Link DIR-604 User Manual
Section 3 - Configuration
AP Mode Opening Page
Once logged into the Web interface of the Router in AP Mode, the Device Information page will appear. This displays
the SSID, Channel, and Encryption status. To make changes to your wireless network, click Setup to access the
Wireless Connection page.