D-MAX DCK-500B User manual

DCK-500B
USER MANUAL
CONTROL KEYBOARD

2
1. Caution before installation ……………………………. 3
2. Features & Distinctions ………………………………... 5
1). Components ……………………………………………………………………………. 5
2). Summary & Features …………………………………………………………………. 6
3). Keyboard Functional Keys …………………………………………………………... 7
4). Junction Box …………………………………………………………………………… 9
3. How to Use in Detail ……………………………………. 10
1). Basic Connection ……………………………………………………………………… 10
2). How to set at Beginning ……………………………………………………………… 11
3). Control Mode Setup …………………………………………………………………… 19
1. PTZ Control Mode Setup and Functions ………………………………………….. 21
2. Setup for MATRIX Control Mode …………………………………………………… 27
3. Setup for Direct Mode ……………………………………………………………….. 29
4. Setup for DVR Control Mode ……………………………………………………….. 30
4). Other Detailed Functions …………………………………………………………….. 33
5). OSD Setup Mode ………………………………………………………………………. 33
6). Other Setup Mode ……………………………………………………………………... 34
4. More Cautions and Check Points ……………………. 37
5. Dimensions ……………………………………………… 39
6. SYSTEM Configuration ………………………………… 40
7. General Specifications ………………………………… 43
8. Quick Reference ………………………………………… 45
CONTENTS

3
1. Caution before installation
Thank you very much for having D-max keyboard. You are strongly required to study this
manual before installation. Facing problem or something you don’t understand while
using, please consult with your systems installers or service personnel.
Caution before Installation
Install the unit after you read following advice.
Avoid installing in places as below,
□Places with too much high or low temperatures
zExtreme temperatures will damage the unit.
zAlways use it within the recommended temperature range of 0℃to 40℃
□Where there are excessive dust, smoke, moisture or humidity.
zUsing this appliance under such conditions may result in fire, electrical
shock or other serious damage
□Where the unit can be blended with all kinds of oil or gas
zIt may cause the problem if you expose in those conditions.
□Places with vibration or impact
zExcessive shock may damage the appliance
□Do not place the appliance in direct sunlight
zIt may discolor the unit or cause a problem.
□Places with high frequency waves, power cables
zUsing the appliance under conditions such as electromagnetic waves
cause a problem.

4
Caution in use
Install the unit after you read following advice.
Avoid following acts,
□Do not try to disassemble the appliance or put any foreign element.
zIt may cause a problem.
□Turn the power off before installation.
zBefore you install the unit, please check the power voltage and turn the
switch on.
□Never have the unit impacted or operated.
zIf you expose the unit to the strong impact or if the button or terminal are
forced to operate, it will be damaged.
(Be careful in using the joystick in particular, if you put too much power on it
while moving left, right or zoom, it may be damaged)
This product has been designed and manufactured in accordance with the harmonized
European standards, following the provisions of the below stated directives.
Electromagnetic Compatibility Directive 89/336/EEC(EN61000-3-2:1995, EN61000-3-
3:1995, EN50081-1:1992, EN50082-1:1997)
This devise complies with part 15 of the fcc rules operation is subject to the following two
conditions: (1) This device may not cause harmful interference and (2) This device must
accept any interference received including interference that may cause undesired
operation

5
2. Features & Distinctions
1). Components
① Body of the Keyboard
② Data Box (Junction Box)
③ Connector Cable (Modular jack)
④ User Manual

6
2). Summary & Features
1. Summary
This unit is a multiple CCTV control keyboard enables to control Speed Dome Camera, CCTV
Receiver, Matrix System, DVR and so on. You can set up a variety of functions of the speed
dome camera and make efficient use of the dome camera for better surveillance by gearing all
kinds of sensors.
This appliance can be used as a Matrix main(sub) keyboard, CCTV Transmitter main(sub)
keyboard at user’s option.
This manual is explaining only about controlling CCTV Transmitter, please refer to the matrix
manual for the detailed use of D-MAX Matrix system.
2. Features
• Locking monitor and camera control.
• Convenient control by 5.0 Inch Touch Screen
• Controls up to 512 cameras.
• Controls maximum 32 monitors (when connecting with matrix, DMX-25632)
• Controls maximum 99 DVR
• Pan/ Tilt/ Zoom controlled by 3-axis joystick.
• Max. 250 Preset widens the surveillance area.
• PAN/ TILT Swing (Auto Pan)
• 12 Group-Tour
• Set and Run the Tour
• Set and Run PTZ Trace.
• Set up on OSD menu of the camera.
• Set and Run Spiral.
• Gearing with alarm receiver unit
• Control H.264 DVR by Jog-shuttle & LCD Touch Screen
• Users with password only can set up the function.
• Set-up PTZ Camera, Monitor User’s Authority
• Display a live view for one channel on LCD screen

7
3). Keyboard Functional Keys
1. Upper Section
1) F/N : “Zoom In” function when use Zoom camera and “ESC (Escape)” function
2) F/F : “Zoom Out” function when use Zoom camera and “Confirm” function when set menu
3) Numeric keypad : used to input numerical value or other functions
4) CLR (CLEAR) : Used to cancel input command or number.
5) ENT (ENTER) : press this key to input command or save, run designated commands
6) SET : Use this key for camera Setup or Keyboard User’s Setup Mode.
7) P-SET : Used to set “PRESET”. Please study explanation of each section for more
detailed function.
8) MENU : This button is use to setup the function with number button. (Refer to function
guidance)
9) ALARM : activate or release the alarm when gearing dome camera with ARU (alarm
receiver unit)
10) WEB-MONITOR: If an Internet Option Board was installed into Matrix System, DVI signal
would be outgoing. In the future, it would be added the Control function of this.
11) DVR : Press this key to enter “DVR Control Mode” or select DVR by using numeric key
together.
12) MON : Selects monitor

8
13) CAM : Selects camera
14) Joystick: This joystick is used to control the pan/tilt/ zoom and move the cursor in the
OSD menu.
15) Color LCD (Screen): It has many different buttons for each function and supports real-
time Video.
16) Sensor: allows to remotely control keyboard with remote controller (soon be released)
17) Jog-shuttle: controls DVR
2. Rear Section
1) RJ-45 Connector: Connection Port with Junction Box & Matrix System
2) VIDEO Input Connector: Input Port for Video signal

9
4). Data Box (Junction box)
Set the communication mode to either RS-485 or RS-422 at your option.
INPUT/OUTPUT TERMINAL OF DATA JUNCTION BOX
Camera controls 1: This is the terminal that you can connect with up to 128 speed dome
cameras or receivers.
(Choose either 485 or 422 communication mode and connect in parallel)
Camera controls 2: this is the terminal that you can connect with up to 128 speed dome
cameras or receivers.
(Choose either 485 or 422 communication mode and connect in parallel)
(All together, 256 cameras can be controlled as above connection)
Sub keyboard: This is the terminal that you can connect sub-keyboard with when hoping to
use sub-keyboard and it does duplex transmission.
(Parallel connection is available when using RS485, but if you use RS422 only
1:1 connection is available.)
485+ 485- NC NC
GND
485+ 485- N C N C
GND
485+ 485- N C N C
GND
RX
RTS
RX
RTS
접지
422
OUT
422
OUT-
422
IN+
422
IN-
422
OUT+
422
OUT-
422
IN+
422
IN-
422
OUT
422
OUT-
422
IN+
422
IN-
CAMERA CONTROL 1 CAMERA CONTROL 2 SUB KEYBOARD
When communicating in RS-485, the switch(485/422)
at both sides should be moved to RS-485.
(It is set to RS-485 when we take from warehouse)

10
3. How to Use in Detail
1). Basic Connection
2 lines (485+, 485-) can be used for data line.
(Ground could be of help when earth is stable, but normally 485+, 485- can be used for data
connection)
485-:
485+:
Sub Keyboard
Main Keyboard

11
2). How to set at Beginning
- If the Power is given to the Unit, After loading of Introduction Screen, the below picture
would be appeared.
1. Factory Default
MAIN Keyboard PTZ Control mode Protocol : D-max 9600 CAM : 001 / DVR : 001
2. Setting the ‘SETUP Mode’
On this mode, Main/ Sub Keyboard can be selected and communication setup of camera or
monitor can be set and Password Setup can be made.
① Hold the key for 3 seconds and blank for password input will appear on the LCD as
below,

12
② Input PASSWORD.
(Default is 0000)
③ If password is input, Setup mode will show up.
SET CAMERA
Setup for communication and usage of camera connected to this unit can be set here.
① Touch ‘SET CAMERA’ button on screen, then will go into “SET-UP” mode
② Move the Joystick up/down, left/right and set by turning upper Joystick.
• SELECT CAMERA
-Direct: Choose this when PTZ camera
is directly connected to keyboard or
Matrix..
-DVR mode: Select this mode when PTZ
Camera is connected to DVR.
-Do not use: It is used to lock the
camera so It can not be controlled.
♦ Max. 512 cameras set can be made..

13
• PROTOCOL/SPEED
- D-max, Pelco-P, Pelco-D, Samsung Techwin / 9600, 4800, 2400bps can be chosen.
③ Press F/F button : After Save the set-up data and then move to Top Menu
Press F/N button : Escape set-up menu and then move to previous menu screen
④ After finish to select Camera, press “SET” button. Then move out to “Control Mode” screen.
MONITOR Setup
You can set the Monitors here and make it useful or useless from this keyboard.
① Touch ‘SET MONITOR’ button on screen, then will go into “SET-UP” mode
③ Press F/F button : After Save the set-up data and then move to Top Menu
Press F/N button : Escape set-up menu and then move to previous menu screen
④ After finish to set-up, press “SET” button. Then move out to “Control Mode” screen.
• Max. 32 Monitors can be set.
• Move to “Monitor No” you like by using
Joystick up/ down, left/ right.
• You can turn it on/ off by turning the
upper Joystick(Head) clockwise or counter
clockwise.
-USED: Monitor in Use
-NOT USE: Monitor not in Use

14
KEYBOARD SETTING
Here you can select the usage of the keyboard.
① Touch ‘SET KEYBOARD’ button on screen, then will go into “SET-UP” mode.
② To select Set-up menu by using Joy-stick “UP” & “ Down” moving, and to change
Set-up Value by using Head of Joy-stick “Left” & “Right” turning“.
1) SELECT MAIN/SUB
-The unit can be set as Main Keyboard or Sub Keyboard.
-Default Value is “MAIN KEY”, but could change to “SUB KEY” by using Head of Joy-stick
Left/Right turning.
♦ If select “MAIN / SUB” by SUB KEY, No.2 would be changed to “SUB NUMBER SELECT”.

15
2-1) SET-UP NUMBER OF SUB KEY
-If use it for MAIN KEYBOARD, set-up number of allowed SUB KEYBOARD.
-Available to allow for number of SUB KEYBOARD up-to 14.
2-2) SELECT TO NUMBER OF USING SUB-KEYBOARD
-If use it for SUB KEYBOARD, select to the number of using SUB KEYBOARD.
-Available to select the number of SUB KEYBOARD from 1 to 14.
3) SUB COMM TYPE
- It works by SCOM1=9600bps / SCOM2=38400bps / SCOM3=115200bps for SUB Interface Set-up.
If the Signal Speed is faster, the Reaction Velocity would be faster. But recommend you to set the
lower Signal Speed for long distance transmission or poor transmission situation.
- In case of SCOM1, available to set maximum 8 number of SUB-Keyboard and can connect with
maximum 8pcs of SUB-Keyboard.
4) ALARM TYPE
-ARU(Alarm Receiver Unit): With ARU connected, Alarm signal can be received..
-CAMERA: The camera receives Alarm signal by itself.
5) VIDEO MODE : NTSC/PAL
-Select the Signal type between NTSC and PAL video signals.
-If Video Output is something wrong, please check Video Signal (NSTC or PAL) mode with
Keyboard’s Video Mode. They should be same Video Signal.
③ Press F/F button : After Save the set-up data and then move to Top Menu
Press F/N button : Escape set-up menu and then move to previous menu screen
④ After finish to set-up, press “SET” button. Then move out to “Control Mode” screen.
♦ At First, set-up number of Sub-Keyboards on Main-Keyboard, and then select to exact
Number of Sub-Keyboard which was connect from no.1 to next step by step.
It could be happened an error if the number of Sub-Keyboard is empty Keyboard or select
wrong number of Keyboard.
♦ ex).
1) SELECT MAIN/SUB : MAIN KEY ----------Æ The user wants to use it as Main Keyboard.
2) SELECT SUB KEY Q,ty : 05 ----------Æ It will allow max. 5 Sub keyboards.
3) SUB COMM TYPE : SCOM_MODE3
4) ALARM TYPE : ARU ----------Æ and Alarm signal will be received on ARU.
5) VIDEO MODE : NTSC ----------Æ Video type on Video mode is NTSC.

16
ALARM On/Off
Select to use ARU (Alarm Receiver) which was connected with the Keyboard or Camera
Alarm function.
• In case “ALARM TYPE” is set as “ARU” on the “3. SET KEYBOARD”
① On SET-UP Menu, Press button on LCD Monitor, then will go into SET-UP mode.
② Press F/F button : After Save the set-up data and then move to Top Menu
Press F/N button : Escape set-up menu and then move to previous menu screen
③ After finish to set-up, press “SET” button. Then move out to “Control Mode” screen.
• In case Alarm type is set as ‘CAMERA” on the “3. SET KEYBOARD”
SELECT DVR
Set-Up DVR which is available to control.
① On SET-UP Menu, Press button, then will go into “SELECT DVE” mode.
• Maximum 512 Alarms can be set.
• Move to CAMERA NO. by moving Joystick
Up/ Down.
• Turning the Joystick head clockwise or
counterclockwise, set it to ‘ON’ or ‘OFF’.
-on: Enable
-off: Disable
• Up to 512 Alarms can be set.
• Select ALARM CH ON/OFF.

17
DIRECT MODE
◆ Concept of DIRECT Mode ◆
When Matrix system user set-up and use
Preset function on a specific PTZ camera,
DIRECT Mode is a shortcut menu.
For your information, the user who operates
PTZ camera through Matrix system can use
the DIRECT mode.
This mode is most useful to keep on eye on
Guard Posts and Casino.
On SET-UP Menu, Press button, then will go into “DIRECT MODE SET”.
♦ In case of Samsung DVR, it supports some specialized model, so please ask it to supplier at first.
Using Joy-stick “UP” & “ Down” moving
• D-max H264 DVR
• D-max MPEG4 DVR
• Samsung DVR(SRD)
After select one which it will control to DVR, then
press “F/F” to Save the set-up data and then
move to Top Menu
Sub
j
ect 1 Sub
j
ect 2 Sub
j
ect n

18
TABLE No. – it’s available to set
from 1 to 999 numbers.
User can set Camera number &
Preset number by Joy-stick.
Move the Joy-stick UP/Down,
Left/Right and set by turning upper
head of Joy-stick.
SYSTEM SETUP
This is Factory Re-Set, Set-Up new Password, and Change Multi-language (Third country language)
menu.
① On SET-UP Menu, Press button, then will go into “SYSTEM SETUP” mode.
1) Change Password
Available to change the Password of Keyboard.
① Select ”1) CHANGE PASSWORD” and using Joy-Stick
to move “Left” or “Right”, then will find a window to
input the new Password.
②Input your expected Password (4 words of numeral)
and repeat it again, then will find a message of
“CHANGE PASSWORD” on screen.
③After Change Password, press F/F button to save the new Password and then move to Top Menu.
2) FACTORY RESET
All Setup value will be changed into “DEFAULT”.
①Select ”2) FACTORY RESET” and using Joy-Stick to move “Left” or “Right”, then press ”F/F”
button.
② Show “Rebooting…” message on screen, and then all set-up values would be changed to factory
default values and would be boot up the Keyboard.
3) LANGUAGE
Change UI (User Interface) Language.
①You can change the language when you select “3) LANGUAGE”.
* Selectable Language: KoreanÆJapaneseÆRussianÆPolishÆEnglish
② After select language what you want, press “F/F” button to save this selection. Then the system
would be restarted.
* * * *

19
3). Control Mode Setup
You will come to know more details about PTZ, MATRIX, DIRECT, DVR mode on this
chapter.
Basic Operation Interface
① MAIN/SUB Keyboard Indicator
-It indicates on PTZ/ MATRIX/ DVR mode if the unit is main keyboard or sub keyboard. (It
also shows if the unit is 1st, 2nd or 16th keyboard.
-Please refer to “2. SETTING the SETUP Mode” for main / sub keyboard setup.
② Indicator for Mode status
- It indicates if the current status is in PTZ, MATRIX or DVR mode.
③ Protocol Indicator
-The current protocol set is indicated.
④ Indicator of communication status
① ④
⑥ ⑦
⑧
② ③ ⑤

20
- This section indicates connection status of MAIN/SUB KEYBOARD and signals of MATRIX,
TX, RX.
• MAIN KEYBOARD: If the unit is set as main keyboard, it blinks.
• MAIN/SUB KEYBOARD 1~14: If you have set SBU KEYBOARD, it will be seen in red.
(The first bar would blink when the unit is set as MAIN Keyboard.)
• MATRIX: If the unit is connected with MATRIX, it flickers.
• TX/ RX: They blink when there are TX/ RX signal.
• ALARM : This Light would be flickering when an Alarm signal incomes.
⑤ It indicates Active or Inert status of ALARM. Press button after ALARM is turned
on and it will turn into RED and Alarm will be activated.
⑥ Button for CONTROL MODE conversion
- Whenever this button is pressed, it will be converted from PTZ ▶ MATRIX rotation.
⑦ Input value of Monitor, Camera, DVR and other commands will appear in letters.
⑧ Each CONTROL MODE is shown.
♦ Press button, then will go into DVR mode.
Press state button like as above on LCD screen, then will go into PTZ or MATRIX mode again.
♦ If the Keyboard Controller is “SUB-Keyboard” mode, it doesn’t support “DIRECT MODE”.
Main keyboard
Sub keyboard 1~14
Matrix
TX/RX
Alarm