D-MOO SV-040(6M+H) User manual

Pedicure Spa (Footspa)
Owners’ Manual
Model: SV-040(6M+H）
Basin: 8169
Manufactured Date：March, 2018
Serial Number ：
Installation Date：

Introduction ----------------------------------------------------------------------------------
We sincerely thank you for purchasing our pedicure spa ( footspa )on the
market ! This innovative whirlpool footspa has been designed to service your
clients from head to toe dependably. Please take time to read through this
entire manual before installation and use.
PLEASE READ AND FOLLOW INSTRUCTIONS CAREFULLY !
Upon the receipt of your footspa , please inspect cartons carefully for
shipping damage immediately upon arrival. Contact your supplier or
customer support if any damage is found.
Important Precautions -------------------------------------------------------------------
We require that you should contact your local, qualified electrician and plumber
to install your whirlpool footspa . It can not operate efficiently or safely unless it
is provided with adequate electrical power, sufficient water pressure, proper
water temperature and required drain facilities. Information on these important
subjects are contained in this manual. We urge you to read it carefully to make
sure these requirements are met.
Precautions -----------------------------------------------------------------------------------
Excessive water temperature is dangerous and should be checked before
use. Maximum water temperature should not exceed 100 deg.F. ( 38
deg.C. )
Always enter and exit the foot spa slowly and carefully.
Never bring and / or operate any electrical devices into the foot spa.
Do not stand in the whirlpool tub !
This foot spa has a weight capacity of 250lb ( 113 KGS ).
Warning ---------------------------------------------------------------------------------------
Do not use if you are diabetic, have poor circulation , or if any area of your feet
or leg are inflamed or have open wounds. Consult your physician before using
if you have any kind of fungal infection, swelling , fracture , or persistent pain.
Massage should be pleasant and comfortable . IF YOU EXPERIENCE PAIN
OR DISCOMFORT, DISCONTINUE USE IMMEDIATELY AND CONSULT
YOUR PHYSICIAN.
Page 1 of 5

Important Installation Considerations ----------------------------------------------
Electrical Service
Check the voltage first and install a leak current breaker by a licensed
electrician to ensure the safety operation.
Each footspa must have its own dedicated 230V, 60 Hz /15 Amp GFCI
protected grounded circuit .
Water Supply
Water supply to the foot spa should consist of a system that will provide
both adequate water pressure and water temperature. All plumbing
connections must conform to local codes.
Normal water pressure is required to correctly fill the tub to the proper
level. ( water spout should not be inundated with water ).
Drain Facilities
Connect the footspa drain system with enclosed drain pipe before you
drain water from the tub. You can ask your local, qualified electrician and
plumber to install a discharge pump if necessary.
Footspa must be securely fastened to the floor
Fasten the footspa with at least two fasteners at each side for safety.
Installation Summary ---------------------------------------------------------------------
The installation must comply with local , state , and national building, plumbing
and electrical codes, where applicable. A licensed plumber should complete
the plumbing of the foot spa.
Step 1 ：Location
Select a level location where the floor structure beneath the Footspa is
capable of supporting the Footspa. For the seat back to fully recline the
Footspa base must be mounted a minimum distance from the wall.
Page 2 of 5

Step 2 ：Attaching Chair with Base
Your Footspa is shipped with base and chair already attached at separate
carton box. However, you must install the chair on the base using the
supplied nut. Must sure that you fasten the chair with base .
Step 3 ：Plumbing and Electrical Connections
All plumbing connections should be made by a qualified, licensed plumber
in accordance with local plumbing and building codes. Carefully connect
hot and cold water supply lines to a fresh water sources.
Check the voltage first and install a leak current breaker by a licensed
electrician to ensure the safety operation.
Step 4 ：Testing The Footspa and Chair
Clean the tub and fill with water. When the tub is filled with water, turn the
switch on the front of the Footspa to activate the whirlpool pump. Water
should be coming out the jets. Use the same switch to turn the whirlpool
pump off and drain the tub by opening the overflow waste control handle.
Turning on the drain pump if your Footspa was installed .
Press the chair power button on the hand held remote controller to testing
all massage functions on enclosed operating instructions.
Massage System See Enclosure A -------------------------------------
Operating The Footspa --------------------------------------------------------------------
TO Fill ：
Close the overflow waste control value. Utilizing the single faucet located
on the front of the Footspa to fill the tub. Note that all jets must be
submerged. If during operation of the whirlpool , water level decreases,
simple add more water.
Page 3 of 5

TO Start and OFF ：
Press the switch ON/OFF on the front panel.
IMPORTANT : DO NOT turn the Footspa “ ON” unless adequate water is
in the tub. THE WARRANTY IS VOLD WHEN THE PUMP HAS BEEN
RUN WITHOUT ADEQUATE WATER. DO NOT BLOCK THE JETS
DURING WHIRLPOOL OPERATION.
To Drain ：
Do not drain the tub until the pump is OFF and has completely stopped.
Turn the overflow waste control value to drain the water from the tub.
Cleaning and Care of The Footspa ----------------------------------------------------
Thorough cleaning is key. Good care requires both cleaning the basin after
each customer and flushing the entire system periodically. How often the
system needs flushed depends largely on your volume. Be careful not to use
anything that could scratch or gouge the surface, as those places can become
breeding grounds for bacteria.
Drain all water and remove debris from the Footspa.
Flush out your spas on a regular basis with clear water. Let the whirlpool
run for 10-15 minutes then drain the tub.
Clean the surfaces and walls of the Footspa with soap or detergent with
clean, clear water then wipe dry with a clean towel.
It is also a good idea to remove the filter screen over the whirlpool inlet
regularly and wash it with a chlorine solution.
Spot clean with mild soap and water for chair seat cleaning.
Page 4 of 5

Limited Warranty ----------------------------------------------------------------------------
We manufacture the Footspa under high standards of workmanship and with
high quality materials. According our expressly warrant the footspa as below:
TO the original owner of the footspa . We may repair or exchange at its option,
any Footspa found to be defective in material or workmanship upon inspection
by our authorized distributor. This warranty covers the following components
for the following time periods :
Recirculation Pump : One year from date of shipment.
Electric Motors : One year from date of shipment.
Footspa Shell: One year from date of shipment.
The exchange of a Footspa is limited to supplying a replacement Footspa of a
comparable style and size. Owner must pay all labor and delivery charge
necessary to replace or repair the Footspa. PLEASE NOTE: This warranty is
null and void if the Footspa is removed from its place of initial installation, or is
not installed in accordance with federal, state or local codes and ordinances.
Furthermore, this warranty does not apply if the Footspa has been subject to
misapplication, improper installation or maintenance or other circumstances
beyond our can control. Should service be required for any reason of any
defect during the warranty period, please contact the below distributor.
Page
Page 5 of 5
Stamp of Distributor

Instruction of Assemble
Suit the holes of chair arm to the metal
frame at the bottom of chair seat then
lock it by enclosed tool
Suit the holes of swivel to the metal
frame at the bottom of chair seat then
lock it by enclosed tool.
Insert four bolts with washers into the
hole of spa base.
Lock washer and nut from the below of
the spa base.
Make sure lock it tightly for safety

Specification For Functional Massage System
L082
1. POWER SWITCH: Press once, power on. Press again, power off. The
power will be shut down after times up.
2. ZONE SWITCH: Seven massage programs for different position could be
chosen and the eighth pattern will stop all functions. LED flash change as
follow: M1->M2->M3->M1+M2->M2+M3->M1+M3->M1+M2+M3.
3. FUNCTION SWITCH: Three massage functions could be chosen
--- Pulse: Massage progress is from up to down step by step. In order to
massage smooth and comfortable, the frequency for motors could be
changed automatically.
---Wave: Vibrating massage progress for all position at the same time, and
intensity for vibration move in circles from strong to weak.
---Ripple: Partial massage and the speed for motor is fast and slow from
up to down.
4. INTENSITY SWITCH: Three speeds for massage and could be set as
personal like. This function can match with all massage programs.
5. HEATING SWITCH: Press once, start heater; press again, stop the
function.