Dacor DMR24M977WS User manual

Table of Contents
Important Safety Instructions ..........................2
What You Need to Know
About Safety ............................................2
Safety Symbols and Labels .........................2
Installation Requirements ................................3
Important Notes To The Installer .................3
Important Notes To The Consumer...............3
Grounding Instructions...............................3
24" Flush Mount Installation Instructions ........4-5
30" Flush Mount Installation Instructions ........6-7
Information You Need To Know.........................8
Model and Serial Number Location ...............8
Care, Cleaning and Maintenance..................8
Before You Call for Service..........................8
Microwave In-A-Drawer™
Part No. 115213 Rev B TINSKB223MRR0
For Use With:
DMR24M977WM/DMR24M977WS
DMR30M977WM/DMR24M977WS
Model DMR24M977W
Flush Mount Installation Instructions

E2
Important Safety Instructions
WARNING
•If the information in this manual is not followed exactly, a re or electrical shock may result that could cause
property damage, personal injury or death.
•To reduce the risk of tipping, the Microwave In-A-Drawer™ must be secured by a properly installed anti-tip block.
•This drawer must be electrically grounded in accordance with local codes.
•Make sure the wall coverings and the cabinets around the drawer can withstand the heat generated by the
microwave.
•Never leave children alone or unattended in the area where a microwave is in use. Never leave the
drawer open when the microwave is unattended.
•Stepping, leaning or sitting on the drawer may result in serious injuries and can also cause damage to the
Microwave In-A-Drawer™.
• Do not use the drawer as a storage space. Doing so creates a potentially hazardous situation.
•Check that the time-of-day is on the display. If not, touch S T O P/C L E A R to prevent unintended use.
WHAT YOU NEED TO KNOW ABOUT
SAFETY INSTRUCTIONS
Warnings and Important Safety Instructions appearing in
this guide are not meant to cover all possible conditions
and situations that may occur. Always use common
sense, caution and care when installing, maintaining or
operating this appliance.
Always contact Dacor
®
about problems or conditions you
do not understand.
SAFETY SYMBOLS AND LABELS
DANGER
Immediate hazards that WILL result in severe
personal injury or death.
WARNING
Hazards or unsafe practices that COULD result in
severe personal injury or death.
CAUTION
Hazards or unsafe practices that COULD result in
minor personal injury or property damage.
Installer: Leave these instructions with the appliance.
Customer: Please read and keep these installation
instructions for future reference. This guide provides
proper installation information.
If you have any questions, call:
Dacor Customer Service
1-800-793-0093 (U.S.A. and Canada)
Monday — Friday 6:00 am to 5:00 pm Pacic Time
Web site: www.Dacor.com
Have the complete model and serial number identication
of your appliance ready. These numbers are found on a
rating label, located on the faceplate behind the drawer
front. See page 6.

E3
HeadingInstallation Requirements
The importance of the proper installation of your new
appliance cannot be overemphasized. Installation should
be done by a qualied installer.
Before you begin the installation process, read this entire
installation instruction manual. It contains information
necessary for proper, safe installation.
Any questions or problems with the installation should
be directed to your Dacor dealer or the Dacor Customer
Service Department at 800.793.0093. You can also visit
our web site at www.Dacor.com.
IMPORTANT NOTES TO THE
INSTALLER
•Read all of the installation instructions before
installing the Microwave In-A-Drawer™.
•Remove all packing material before connecting
the electrical supply.
• Observe all governing codes and ordinances.
•Be sure to leave these instructions with the
consumer.
IMPORTANT NOTES TO THE
CONSUMER
Keep these instructions with your use & care manual for
future reference.
•When using any microwave oven generating
heat, there are certain safety precautions you
should follow, that are listed in the use & care
manual. Read the use and care manual and follow
all safety precautions carefully.
•Be sure your Microwave In-A-Drawer™ is installed
and grounded properly by a qualied installer or
service technician.
For SAFETY CONSIDERATIONS do not install the drawer
in any combustible cabinetry, which is not in accord with
the stated clearances and dimensions on pages 3, 4 and
5. See Figure 2 (for 24") or Figures 4 and 5(for 30").
GROUNDING INSTRUCTIONS
WARNING
Improper use of the grounding plug can result in a
risk of electric shock.
This appliance is equipped with a three-prong grounding
plug for your protection against possible electric
shock hazards. It must be plugged into a grounded
wall receptacle. If only a two-prong wall receptacle
is available, it is the responsibility of the customer to
have it replaced with a properly grounded three-prong
wall receptacle. Do not under any circumstances,
cut or remove the third (ground) prong from the
power cord. Do not use an adapter plug. Do not use
an extension cord. If the power supply cord is too short,
have a qualied electrician or serviceman install an outlet
near the appliance. Do not use a Ground Fault Circuit
Interrupter.
Power supply cord with
three-prong grounding plug
Grounding type wall receptacle
(ground fault circuit not allowed)

E4
Heading24" Flush Mount Installation Instructions
Parts include:
Qty. Part
DMR24M977WM/S
1PREF-B019MRP0
Flush Mount Deector Vent
Stainless Steel
2LX-CZB055MRE0
Mounting screws
1. Prepare cabinet opening as shown in Figures 1, 2A, 2B, 2C.
C
N
H
E
F
D
A
B
J
L
I
M
K
G
Note: the face of the shelf must
sit 1 3/4"(44.45 mm) back from
the face of the cabinet.
cabinet face
shelf face O
Figure 1
Figure 2A
A. 6" (152.40 mm)
B. Suggested electrical outlet location
C. Anti-Tip block
D. 5" (127 mm)
E. 3 1/2" (88.90 mm)
F. 4" (101.60 mm)
G. 24 3/16" (614.35 mm) minimum
24 1/2" (622.3 mm) maximum
H. 14 13/16" (376.24 mm) to
bottom of Anti-Tip block
I. 1 1/16" (26.97 mm)
J. 23 1/2" (596.90 mm)
minimum depth
K. 22 1/8" (561.97 mm)
L. 1 3/4" (44.45 mm)
M.16 7/8" (428.62 mm) opening
N. Floor must support 100 lb (45.4 kg)
O. 1 3/4" (44.45 mm)
CL
Top view
A
Anti-Tip block
Mounting cleat
BC
Drawer face Cabinet
face
Note: the mounting surface of the finished cleat must sit 1 1/16" (26.97 mm)
back
from the face of the cabinet [pushing the face of the drawer out
1
/4" (6.35 mm)].
A. 22" (558.8 mm) mounting cleat
opening width
B. 1/4" (6.35 mm)
C. 1 1/16" (26.97 mm)

E5
Heading24" Flush Mount Installation Instructions
Shelf detail showing the deflector vent installed.
Shelf detail showing the deflector vent during installation.
Position deflector vent and mark holes. Pre drill using a
1/16" (1.57 mm)
bit before mounting.
C
Front view
No oven
B
A
Suggested electrical
outlet location
Anti-Tip block
3/4"(19.05 mm)
shelf
Side view
1 3/4" (44.45 mm)
front face of shelf
Front face of cabinet
16 7/8"
(428.62 mm)
flush opening
height
Move oven location
downward for extended
countertops for better
viewing angle. Anti-Tip
block
3. Place the drawer adjacent to the wall or cabinet
opening. Plug the power supply cord into the electrical
outlet.
4. Carefully guide the drawer into the prepared opening.
Avoid contact with the sides of the cutout opening and
also pinching the cord between the oven and the wall.
5. Slide the drawer all the way back until the mounting
anges touch the cleats mounted in the cabinet
opening.
6. Open the drawer. Using the 4 holes on the drawer as a
template, pre drill the cabinet using a 1/16” (1.57 mm)
bit. See Figure 4.
Figure 3A
Figure 4
Figure 3B
2. Install deector as shown in Figure 3A.
7. Secure the drawer with the 4 screws supplied.
Mounting
flange
Figure 2B
Figure 2C
A. 22 1/8" (561.97 mm) mounting
cleat opening width
B. 24 3/16" (614.35 mm) minimum
24 1/2" (622.3 mm) maximum
ush opening width
C. 3/4" (19.05 mm) shelf

E6
Heading30" Flush Mount Installation Instructions
Parts include:
Qty. Part
DMR30M977WM/S
1PREF-B020MRP0
Flush Mount Deector Vent
Stainless Steel
2LX-CZB055MRE0
Mounting screws
1. Prepare cabinet opening as shown in Figures 1, 2A, 2B, 2C.
Figure 1
Figure 2A
A. 6" (152.40 mm)
B. Suggested electrical outlet location
C. Anti-Tip block
D. 5" (127 mm)
E. 3 1/2" (88.90 mm)
F. 4" (101.60 mm)
G. 30 5/16" (769.92 mm) minimum
30 5/8" (777.87 mm) maximum
H. 14 13/16" (376.24 mm) to
bottom of Anti-Tip block
I. 1 1/16" (26.97 mm)
J. 23 1/2" (596.90 mm) minimum depth
K. 28 7/16" (722.3 mm)
L. 1 3/4" (44.45 mm)
M.16 7/8" (428.62 mm) opening
N. Floor must support 100 lb (45.4 kg)
O. 1 3/4" (44.45 mm)
CL
Top view
A
Anti-Tip block
Mounting cleat
BC
Drawer face Cabinet
face
Note: the mounting surface of the finished cleat must sit 1 1/16" (26.97 mm)
back
from the face of the cabinet [pushing the face of the drawer out
1
/
4
" (6.35 mm)].
A. 28 1/2" (723.9 mm)
mounting cleat opening width
B. 1/4" (6.35 mm)
C. 1 1/16" (26.97 mm)
C
N
H
E
F
D
B
A
J
L
I
cabinet face
shelf face O
G
K
M
Note: the face of the shelf must
sit 1 3/4"(44.45 mm) back from
the face of the cabinet.

E7
Heading30" Flush Mount Installation Instructions
3. Place the drawer adjacent to the wall or cabinet
opening. Plug the power supply cord into the electrical
outlet.
4. Carefully guide the drawer into the prepared opening.
Avoid contact with the sides of the cutout opening and
also pinching the cord between the oven and the wall.
5. Slide the drawer all the way back until the mounting
anges touch the cleats mounted in the cabinet
opening.
6. Open the drawer. Using the 4 holes on the drawer as a
template, pre drill the cabinet using a 1/16” (1.57 mm)
bit. See Figure 4.
Figure 3A
Figure 4
Figure 3B
2. Install deector as shown in Figure 3A.
7. Secure the drawer with the 4 screws supplied.
Mounting
flange
Figure 2B
Figure 2C
A. 28 7/16" (722.3 mm) mounting
cleat opening width
B. 30 5/16" (769.92 mm) minimum
30 5/8" (777.87 mm) maximum
ush opening width
C. 3/4" (19.05 mm) shelf
Front view
No oven
C
B
A
Suggested electrical
outlet location
Anti-Tip block
3/4"(19.05 mm)
shelf
Side view
1 3/4" (44.45 mm)
front face of shelf
Front face of cabinet
16 7/8"
(428.62 mm)
flush opening
height
Move oven location
downward for extended
countertops for better
viewing angle. Anti-Tip
block
Shelf detail showing the deflector shield installed.
Shelf detail showing the deflector vent during installation.
Position deflector vent and mark holes. Pre drill using a
1/16" (1.57 mm)
bit before mounting.

E8
Heading
MODEL AND SERIAL NUMBER
LOCATION
The rating label includes the model and serial
number. Open the microwave drawer fully. The
label is located slightly beyond the back wall of the
microwave cavity facing up from the at surface.
Rating Label
CARE, CLEANING AND
MAINTENANCE
Refer to the use & care manual for cleaning instructions.
BEFORE YOU CALL FOR
SERVICE
Read the BEFORE YOU CALL and operating instruction
sections in your use & care manual. It may save
you time and expense. The list includes common
occurrences that are not the result of defective
workmanship or materials in this microwave.
Refer to the warranty in your use & care manual
for Dacor’s toll-free service number and address.
Please call or write if you have inquiries about your
microwave product and/or need to order parts.
Information You Need To Know

Four micro-onde tiroir
Directives d’installation
KEEP
WARM
SOFTEN
MELT
CLOSE
OPEN
EASY MINUTE
SETUP
HELP
CONTROL
LOCK WARM
BEVERAGE
CENTER
SENSOR
POPCORN
SENSOR
COOK
SENSOR
REHEAT
DEFROST REHEAT
Modèle DMR24M977W Pour un usage avec :
Table des matières
Importantes consignes de sécurité................10
Ce que vous devez savoir au sujet des
consignes de sécurité ............................10
Symboles et étiquettes de sécurité ..........10
Conditions d’installation...............................11
Remarques importantes à l’installateur.....11
Remarques importantes au client.............11
Instructions de mise à la terre.................11
Encastré de 24 po d’installation
instructions ..........................................12-13
Encastré de 30 po d’installation
instructions ..........................................14-15
Ce Que Vous Devez Savoir...........................16
Emplacement des numéros de modèle
et de série ...........................................16
Entretien et nettoyage ...........................16
Avant d’appeler le service de réparations ..16
DMR24M977WM/DMR24M977WS
DMR30M977WM/DMR24M977WS

F10
Heading
MISE EN GARDE
•Si l’information contenue dans ce manuel n’est pas exactement suivie, un incendie ou une décharge électrique
pourrait causer des dommages matériels, des blessures personnelles ou la mort.
•Pour réduire le risque de basculement, le four Microwave In-A-Drawer™ doit être xé à l’aide d’un bloc anti-
basculement correctement installé.
•Ce tiroir doit être mis à la terre en conformité avec les codes locaux.
•Vérier que les revêtements muraux et les armoires autour du tiroir peuvent supporter la chaleur générée par le
four à micro-ondes.
•Ne jamais laisser des enfants seuls ou sans surveillance dans un endroit où un four à micro-ondes
fonctionne. Ne jamais laisser le tiroir ouvert quand le four est sans surveillance.
•Le fait de monter, de s’appuyer ou de s’asseoir sur le tiroir peut entraîner de sérieuses blessures et peut également
endommager le four Microwave In-A-Drawer™.
•Ne pas utiliser la cavité comme espace de rangement. Cela crée une situation potentiellement dangereuse.
•Vérier que l’heure s’afche. Sinon, appuyer sur STOP/CLEAR pour empêcher une utilisation non prévue.
CE QUE VOUS DEVEZ SAVOIR AU SUJET
DES CONSIGNES DE SÉCURITÉ
Les mises en garde et les importantes consignes de sécurité
apparaissant dans ce manuel ne couvrent pas toutes les
conditions et situations possibles. Il faut exercer son bon
sens, de la prudence et de l’attention en installant en
entretenant et en utilisant cet appareil.
Toujours communiquer avec Dacor®au sujet des
problèmes ou des conditions que vous ne comprenez
pas.
SYMBOLES ET ÉTIQUETTES DE SÉCURITÉ
DANGER
Risques immédiats qui AURONT pour
conséquence de sévères blessures ou la mort.
MISE EN GARDE
Risques ou comportements non sécuritaires
qui POURRAIENT avoir pour conséquence
de sévères blessures ou la mort.
ATTENTION
Risques ou comportements non sécuritaires
qui POURRAIENT avoir pour conséquence des
blessures mineures ou des dommages matériels.
Installateur : Laisser ces directives avec l’appareil.
Client : Veuillez lire et conserver ce mode d’emploi et
d’entretien pour référence ultérieure. Ce manuel offre
l’information relative à une bonne utilisation et un bon
entretien.
Si vous avez des questions, appelez :
Service à la clientèle de Dacor
1-800-793-0093 (É.-U. et Canada)
Lundi à vendredi, 6 h à 1 h Heure du Pacique
site Web: www.Dacor.com
Ayez en main les numéros de modèle et de série de
votre appareil. Ces numéros se trouvent sur une plaque
de série, située sur une plaque d’identication derrière
la façade du tiroir.
IMPORTANTES CONSIGES DE SÉCURITÉ