Daedong Kioti SMV STEREO KIT User manual

6
1
7
2
8
4
5
3
TC2SP01A
1. PACKING LIST
2. GENERAL SAFETY INFORMATION
3. EXPLODED VIEW
4. INSTALLATION INSTRUCTION
D.D KIT#. T2131-55452
Printed in Korea. FEB. 2018
3. EXPLODED VIEW
(1) ASSY,STEREO
(2) ANTENNA ASSY
(3) ASSY,SPKER
(4) SPRING_WASHER
(5) PLAIN_WASHER
(6) SCREW_WITH_WASHER
(7) CROSS-RECESSED HEAD MACHINE SCREW
(8) NUT
4. INSTALLATION INSTRUCTION
1. Park the vehicle on firm and level ground. Then, engage the parking brake and stop
the engine.
2. Unscrew 6 roof mounting bolts (A) to
remove the roof.
NO. Part No. Description Q'TY Remark
1TG15-0046A ASSY,STEREO 1
2T4810-82421 ANTENNA ASSY 1
3T4810-82341 ASSY, SPEAKER 2
404512-50060 SPRING_WASHER 1
504013-50060 PLAIN_WASHER 2
603024-50420 SCREW_WITH_WASHER 2
703014-50625 CROSS-RECESSED HEAD MACHINE SCREW 1
802114-50060 NUT 1
9T5270-55172 STEREO ACCESSORIES(MANUAL) 1
1. PACKING LIST 2. GENERAL SAFETY INFORMATION
This symbol means ATTENTION! YOUR SATETY IS INVOLVED.
The message that follows the symbol contains important information
about satety. Carefully read the message.
BEFORE SERVICING AND REPAIRING
1. Read all safety instruction in this
manual and be aware of safety decal
locations on your machine.
2. Thoroughly clean your work area and
the machine.
3. Make sure the machine is on firm
and level ground and that the parking
brake is set.
4. Lower the implement to the ground.
5. Stop the engine and remove the key.
6. Disconnect the negative battery cable.
7. Place a "DO NOT OPERATE" tag in
the operator station.
WORKING SAFETY
1. Do not operate or service the machine
while under the influence of alcohol,
medications, or other sustances.
2. Never wear loose fitting clothing and
always use safety equipment appro-
priate to the job.
3. Never use improvised tools, parts or
procedures. Use only recommended
tools appropriate to the work.
4. Extra care should be taken to work
safely when servicing is done by two
or more persons.
5. Always support the machine with safe-
ty stands rated for the weight of the
machine. Never work under a machine
that is supported solely with a jack.
6. Do not touch any rotating or hot parts
while the engine is running.
7. Escaping fluid (hydraulic oil) under pres-
sure can penetrate the skin causing seri-
ous injury. Relieve pressure before dis-
connecting hydraulic or fuel lines. Tighten
all connections before applying pressure.
DISPOSE OF FLUIDS PROPERLY
1. Observe relevant environmental protec-
tion regulations when disposing of oil.
NEVER pour fluids onto the ground,
down a drain, or into any body of water.
A
TC2SU02A
INSTALLATION
INSTRUCTIONS
FOR FOR CK3510(H)/4010(H)
SMV STEREO KIT
Next page▼
3. Attach the antenna assembly (2) to
the removed roof with Phillips screws
(7).
TC2SU03A
SERVICE SUPPORT DIVISION / DAEDONG INDUSTRIAL Co.,Ltd.
35, Nongongjungang-ro 34-gil Nongong-eup, Dalseong-gun, Daegu, KOREA 42984
Tel:[phone] Fax:[phone]
http://www.daedong.co.kr
KIOTI TRACTOR DIVISION / DAEDONG-USA, Inc.
6300 Kioti Dr. Wendell, NC 27591
Toll Free:1877-GO-KIOTI
Tel:[phone] Fax:[phone]
http://www.kioti.com
DAEDONG KIOTI EUROPE B.V
Koerilenstraat 2, 3199LR, Maasvlakte-Rotterdam The Netherlands
Tel:[phone]
http://www.kioti.eu

4. Fit the stereo assembly (1) with the
washer based head bolts (6) from the
inside of the cabin loosely.
TC2SP04A
5. Insert the protrusion (A) of the stereo
assembly into the bracket hole of the
cabin roof and connect the antenna
cable (B) and connector (C).
TC2SP05A TC2SP06A
6. Tighten the bolts completely, which
were loosely tightened in Step 4
above, and install the stereo assembly
cover (A).
TC2SP07A
7. Insert the speaker assembly (3) from
the inside of the cabin and fix it with
the plain washer (5), spring washer (4)
and nut (8) to the roof. Then, connect
the connector (A) to it.
8. Reinstall the removed roof.