Daikin VRV II RXYQ5MY1B User manual

SiE39-404
Service
Manual
R-410A Heat Pump 50Hz

SiE39-404
Table of Contents i
R410A Heat Pump
50Hz
1. Introduction ............................................................................................vi
1.1 Safety Cautions.......................................................................................vi
1.2 PREFACE ................................................................................................x
Part 1 General Information...........................................................1
1. Model Names of Indoor/Outdoor Units....................................................2
2. External Appearance...............................................................................3
2.1 Indoor Units..............................................................................................3
2.2 Outdoor Units...........................................................................................4
3. Combination of Outdoor Units.................................................................5
4. Model Selection......................................................................................6
Part 2 Specifications ....................................................................9
1. Specifications........................................................................................10
1.1 Outdoor Units.........................................................................................10
1.2 Indoor Units............................................................................................21
Part 3 Refrigerant Circuit ...........................................................49
1. Refrigerant Circuit.................................................................................50
1.1 RXYQ5M (*Products after January, 2004)...........................................50
1.2 RXYQ8, 10, 12M (*Products after January, 2004)...............................52
1.3 RXYQ14, 16M (*Products after January, 2004) ..................................54
1.4 Outdoor air processing unit FXMQ125~250MFV1.................................56
2. Functional Parts Layout ........................................................................57
2.1 RXYQ5M................................................................................................57
2.2 RXYQ8, 10, 12M....................................................................................58
2.3 RXYQ14, 16M........................................................................................59
3. Refrigerant Flow for Each Operation Mode...........................................60
Part 4 Function............................................................................73
1. Function general ...................................................................................74
1.1 Symbol ...................................................................................................74
1.2 Operation Mode......................................................................................75
2. Basic Control.........................................................................................76
2.1 Normal Operation...................................................................................76
2.2 Compressor PI Control...........................................................................77
2.3 Electronic Expansion Valve PI Control...................................................83
2.4 Cooling Operation Fan Control...............................................................84

SiE39-404
ii Table of Contents
3. Special Control......................................................................................85
3.1 Startup Control.......................................................................................85
3.2 Oil Return Operation ..............................................................................86
3.3 Defrosting Operation..............................................................................88
3.4 Pump-down Residual Operation ............................................................89
3.5 Restart Standby......................................................................................90
3.6 Stopping Operation ................................................................................91
3.7 Pressure Equalization prior to Startup....................................................93
4. Protection Control .................................................................................94
4.1 High Pressure Protection Control...........................................................94
4.2 Low Pressure Protection Control............................................................95
4.3 Discharge Pipe Protection Control.........................................................96
4.4 Inverter Protection Control .....................................................................97
4.5 STD Compressor Overload Protection...................................................98
5. Other Control.........................................................................................99
5.1 Outdoor Unit Rotation.............................................................................99
5.2 Emergency Operation ..........................................................................100
5.3 Demand Operation...............................................................................102
5.4 Heating operation prohibition ...............................................................102
6. Outline of Control (Indoor Unit)...........................................................103
6.1 Drain Pump Control..............................................................................103
6.2 Louver Control for Preventing Ceiling Dirt............................................105
6.3 Thermostat Sensor in Remote Controller.............................................106
6.4 Freeze Prevention................................................................................108
6.5 Control of outdoor air Processing unit (Unique Control for
Outdoor Air Processing Unit)................................................................109
Part 5 Test Operation ...............................................................113
1. Test Operation ....................................................................................114
1.1 Procedure and Outline .........................................................................114
1.2 Operation When Power is Turned On..................................................117
2. Outdoor Unit PC Board Layout ...........................................................118
3. Field Setting........................................................................................119
3.1 Field Setting from Remote Controller...................................................119
3.2 Field Setting from Outdoor Unit............................................................132
Part 6 Troubleshooting .............................................................157
1. Troubleshooting by Remote Controller ...............................................160
1.1 The INSPECTION / TEST Button.........................................................160
1.2 Self-diagnosis by Wired Remote Controller .........................................161
1.3 Self-diagnosis by Wireless Remote Controller.....................................162
1.4 Operation of The Remote Controller’s Inspection /
Test Operation Button..........................................................................165
1.5 Remote Controller Service Mode.........................................................166
1.6 Remote Controller Self-Diagnosis Function.........................................168
2. Troubleshooting by Indication on the Remote Controller....................173
2.1 “A0” Indoor Unit: Error of External Protection Device ...........................173
2.2 “A1” Indoor Unit: PC Board Defect.........................................................174
2.3 “A3” Indoor Unit: Malfunction of Drain Level Control System (S1L)......175
2.4 “A6” Indoor Unit: Fan Motor (M1F) Lock, Overload...............................177

SiE39-404
Table of Contents iii
2.5 “A7” Indoor Unit: Malfunction of Swing Flap Motor (MA).......................178
2.6 “A9” Indoor Unit: Malfunction of Moving Part of
Electronic Expansion Valve (20E)........................................................180
2.7 “AF” Indoor Unit: Drain Level above Limit..............................................182
2.8 “AJ” Indoor Unit: Malfunction of Capacity Determination Device..........183
2.9 “C4” Indoor Unit: Malfunction of Thermistor (R2T) for Heat Exchanger 184
2.10 “C5” Indoor Unit: Malfunction of Thermistor (R3T) for Gas Pipes..........185
2.11 “C9” Indoor Unit: Malfunction of Thermistor (R1T) for Suction Air.........186
2.12 “CJ” Indoor Unit: Malfunction of Thermostat Sensor
in Remote Controller ............................................................................187
2.13 “E1” Outdoor Unit: PC Board Defect......................................................188
2.14 “E3” Outdoor Unit: Actuation of High Pressure Switch..........................189
2.15 “E4” Outdoor Unit: Actuation of Low Pressure Sensor..........................190
2.16 “E5” Compressor Motor Lock ................................................................191
2.17 “E6” Compressor Motor Overcurrent/Lock ............................................192
2.18 “E7” Malfunction of Outdoor Unit Fan Motor..........................................193
2.19 “E9” Outdoor Unit: Malfunction of Moving Part of
Electronic Expansion Valve (Y1E, Y2E)...............................................195
2.20 “F3” Outdoor Unit: Abnormal Discharge Pipe Temperature..................197
2.21 “F6” Refrigerant Overcharged...............................................................198
2.22 “H7” Abnormal Outdoor Fan Motor Signal.............................................199
2.23 “H9” Outdoor Unit: Malfunction of Thermistor for Outdoor Air (R1T).....200
2.24 “J2” Current Sensor Malfunction...........................................................201
2.25 “J3” Outdoor Unit: Malfunction of Discharge Pipe Thermistor
(R3, R31~33T) .....................................................................................202
2.26 “J5” Outdoor Unit: Malfunction of Thermistor (R2T) for Suction Pipe...203
2.27 “J6” Outdoor Unit: Malfunction of Thermistor (R4T) for
Outdoor Unit Heat Exchanger..............................................................204
2.28 “J8” Malfunction of Oil Equalizing Pipe Thermistor (R7T).....................205
2.29 “J9” Malfunction of Receiver Gas Pipe Thermistor (R5T).....................206
2.30 “JA” Outdoor Unit: Malfunction of Discharge Pipe Pressure Sensor.....207
2.31 “JC” Outdoor Unit: Malfunction of Suction Pipe Pressure Sensor.........208
2.32 “L4” Outdoor Unit: Malfunction of Inverter Radiating
Fin Temperature Rise...........................................................................209
2.33 “L5” Outdoor Unit: Inverter Compressor Abnormal ...............................210
2.34 “L8” Outdoor Unit: Inverter Current Abnormal.......................................211
2.35 “L9” Outdoor Unit: Inverter Start up Error..............................................212
2.36 “LC” Outdoor Unit: Malfunction of Transmission Between Inverter
and Control PC Board..........................................................................213
2.37 “P1” Outdoor Unit: Inverter Over-Ripple Protection ...............................215
2.38 “P4” Outdoor Unit: Malfunction of Inverter Radiating Fin
Temperature Rise Sensor....................................................................216
2.39 “UO” Low Pressure Drop Due to Refrigerant Shortage or
Electronic Expansion Valve Failure......................................................217
2.40 “U1” Reverse Phase, Open Phase.........................................................218
2.41 “U2” Power Supply Insufficient or Instantaneous Failure ......................219
2.42 “U3” Check Operation not executed......................................................221
2.43 “U4” Malfunction of Transmission Between Indoor Units ......................222
2.44 “U5” Malfunction of Transmission Between Remote Controller
and Indoor Unit.....................................................................................224
2.45 “U7” Malfunction of Transmission Between Outdoor Units....................225
2.46 “U8” Malfunction of Transmission Between Master and
Slave Remote Controllers ....................................................................227

SiE39-404
iv Table of Contents
2.47 “U9” Malfunction of Transmission Between Indoor and
Outdoor Units in the Same System......................................................228
2.48 “UA” Excessive Number of Indoor Units................................................230
2.49 “UC” Address Duplication of Central Remote Controller........................231
2.50 “UE” Malfunction of Transmission Between Central Remote
Controller and Indoor Unit....................................................................232
2.51 “UF” Refrigerant System not Set, Incompatible Wiring/Piping...............234
2.52 “UH” Malfunction of System, Refrigerant System Address Undefined...235
3. Troubleshooting (OP: Central Remote Controller)..............................236
3.1 “UE” Malfunction of Transmission Between Central Remote
Controller and Indoor Unit....................................................................236
3.2 “M1” PC Board Defect ............................................................................237
3.3 “M8” Malfunction of Transmission Between Optional Controllers
for Centralized Control .........................................................................238
3.4 “MA” Improper Combination of Optional Controllers for
Centralized Control...............................................................................239
3.5 “MC” Address Duplication, Improper Setting..........................................241
4. Troubleshooting (OP: Schedule Timer)...............................................242
4.1 “UE” Malfunction of Transmission Between Central Remote
Controller and Indoor Unit....................................................................242
4.2 “M1” PC Board Defect ............................................................................244
4.3 “M8” Malfunction of Transmission Between Optional Controllers for
Centralized Control...............................................................................245
4.4 “MA” Improper Combination of Optional Controllers for
Centralized Control...............................................................................246
4.5 “MC” Address Duplication, Improper Setting..........................................248
5. Troubleshooting (OP: Unified ON/OFF Controller) .............................249
5.1 Operation Lamp Blinks.........................................................................249
5.2 Display “Under Host Computer Integrate Control” Blinks
(Repeats Single Blink)..........................................................................251
5.3 Display “Under Host Computer Integrate Control” Blinks
(Repeats Double Blink) ........................................................................254
Part 7 Replacement procedure for INV compressor,
VRV II (RXYQ5M to 48M)................................................257
1. Replacement procedure for INV compressor,
VRV II (RXYQ5M-48M).......................................................................258
1.1 Replacement procedure.......................................................................258
Part 8 Appendix.........................................................................259
1. Piping Diagrams..................................................................................260
1.1 Outdoor Unit.........................................................................................260
1.2 Indoor Unit............................................................................................263
2. Wiring Diagrams for Reference...........................................................269
2.1 Outdoor Unit.........................................................................................269
2.2 Field Wiring ..........................................................................................272
2.3 Indoor Unit............................................................................................275
3. List of Electrical and Functional Parts.................................................293
3.1 Outdoor Unit.........................................................................................293
3.2 Indoor Side...........................................................................................295

SiE39-404
Table of Contents v
4. Option List...........................................................................................301
4.1 Option List of Controllers......................................................................301
4.2 Option Lists (Outdoor Unit)...................................................................303
5. Piping Installation Point.......................................................................304
5.1 Piping Installation Point........................................................................304
5.2 The Example of A Wrong Pattern.........................................................305
6. Selection of Pipe Size, Joints and Header..........................................306
6.1 RXYQ5MY1B, RXYQ8MY1B, RXYQ10MY1B, RXYQ12MY1B,
RXYQ14MY1B,
RXYQ16MY1B .....................................................................................306
6.2 RXYQ18MY1B, RXYQ20MY1B, RXYQ22MY1B, RXYQ24MY1B,
RXYQ26MY1B, RXYQ28MY1B, RXYQ30MY1B, RXYQ32MY1B,
RXYQ34MY1B, RXYQ36MY1B, RXYQ38MY1B, RXYQ40MY1B,
RXYQ42MY1B, RXYQ44MY1B, RXYQ46MY1B, RXYQ48MY1B .......308
7. Thermistor Resistance / Temperature Characteristics........................311
8. Pressure Sensor .................................................................................313
9. Method of Replacing The Inverter’s Power Transistors
and Diode Modules.............................................................................314
Part 9 Precautions for New Refrigerant (R410) .......................317
1. Precautions for New Refrigerant (R410).............................................318
1.1 Outline..................................................................................................318
1.2 Refrigerant Cylinders............................................................................320
1.3 Service Tools........................................................................................321
Index .............................................................................................i
Drawings & Flow Charts ................................................................v

Introduction SiE39-404
vi
1. Introduction
1.1 Safety Cautions
Cautions and
Warnings
Be sure to read the following safety cautions before conducting repair work.
The caution items are classified into “ Warning” and “ Caution”. The “ Warning”
items are especially important since they can lead to death or serious injury if they are not
followed closely. The “ Caution” items can also lead to serious accidents under some
conditions if they are not followed. Therefore, be sure to observe all the safety caution items
described below.
About the pictograms
This symbol indicates an item for which caution must be exercised.
The pictogram shows the item to which attention must be paid.
This symbol indicates a prohibited action.
The prohibited item or action is shown inside or near the symbol.
This symbol indicates an action that must be taken, or an instruction.
The instruction is shown inside or near the symbol.
After the repair work is complete, be sure to conduct a test operation to ensure that the
equipment operates normally, and explain the cautions for operating the product to the
customer
1.1.1 Caution in Repair Warning
Be sure to disconnect the power cable plug from the plug socket before
disassembling the equipment for a repair.
Working on the equipment that is connected to a power supply can cause an
electrical shook.
If it is necessary to supply power to the equipment to conduct the repair or
inspecting the circuits, do not touch any electrically charged sections of the
equipment.
If the refrigerant gas discharges during the repair work, do not touch the
discharging refrigerant gas.
The refrigerant gas can cause frostbite.
When disconnecting the suction or discharge pipe of the compressor at the
welded section, release the refrigerant gas completely at a well-ventilated
place first.
If there is a gas remaining inside the compressor, the refrigerant gas or
refrigerating machine oil discharges when the pipe is disconnected, and it can
cause injury.
If the refrigerant gas leaks during the repair work, ventilate the area. The
refrigerant gas can generate toxic gases when it contacts flames.
The step-up capacitor supplies high-voltage electricity to the electrical
components of the outdoor unit.
Be sure to discharge the capacitor completely before conducting repair work.
A charged capacitor can cause an electrical shock.
Do not start or stop the air conditioner operation by plugging or unplugging the
power cable plug.
Plugging or unplugging the power cable plug to operate the equipment can
cause an electrical shock or fire.

SiE39-404 Introduction
vii
1.1.2 Cautions Regarding Products after Repair
Caution
Do not repair the electrical components with wet hands.
Working on the equipment with wet hands can cause an electrical shock.
Do not clean the air conditioner by splashing water.
Washing the unit with water can cause an electrical shock.
Be sure to provide the grounding when repairing the equipment in a humid or
wet place, to avoid electrical shocks.
Be sure to turn off the power switch and unplug the power cable when cleaning
the equipment.
The internal fan rotates at a high speed, and cause injury.
Do not tilt the unit when removing it.
The water inside the unit can spill and wet the furniture and floor.
Be sure to check that the refrigerating cycle section has cooled down
sufficiently before conducting repair work.
Working on the unit when the refrigerating cycle section is hot can cause burns.
Use the welder in a well-ventilated place.
Using the welder in an enclosed room can cause oxygen deficiency.
Warning
Be sure to use parts listed in the service parts list of the applicable model and
appropriate tools to conduct repair work. Never attempt to modify the
equipment.
The use of inappropriate parts or tools can cause an electrical shock,
excessive heat generation or fire.
When relocating the equipment, make sure that the new installation site has
sufficient strength to withstand the weight of the equipment.
If the installation site does not have sufficient strength and if the installation
work is not conducted securely, the equipment can fall and cause injury.
Be sure to install the product correctly by using the provided standard
installation frame.
Incorrect use of the installation frame and improper installation can cause the
equipment to fall, resulting in injury.
For integral units
only
Be sure to install the product securely in the installation frame mounted on a
window frame.
If the unit is not securely mounted, it can fall and cause injury.
For integral units
only
Be sure to use an exclusive power circuit for the equipment, and follow the
technical standards related to the electrical equipment, the internal wiring
regulations and the instruction manual for installation when conducting
electrical work.
Insufficient power circuit capacity and improper electrical work can cause an
electrical shock or fire.

Introduction SiE39-404
viii
1.1.3 Inspection after Repair
Be sure to use the specified cable to connect between the indoor and outdoor
units. Make the connections securely and route the cable properly so that there
is no force pulling the cable at the connection terminals.
Improper connections can cause excessive heat generation or fire.
When connecting the cable between the indoor and outdoor units, make sure
that the terminal cover does not lift off or dismount because of the cable.
If the cover is not mounted properly, the terminal connection section can cause
an electrical shock, excessive heat generation or fire.
Do not damage or modify the power cable.
Damaged or modified power cable can cause an electrical shock or fire.
Placing heavy items on the power cable, and heating orpulling the power cable
can damage the cable.
Do not mix air or gas other than the specified refrigerant (R410A) in the
refrigerant system.
If air enters the refrigerating system, an excessively high pressure results,
causing equipment damage and injury.
If the refrigerant gas leaks, be sure to locate the leak and repair it before
charging the refrigerant. After charging refrigerant, make sure that there is no
refrigerant leak.
If the leak cannot be located and the repair work must be stopped, be sure to
perform pump-down and close the service valve, to prevent the refrigerant gas
from leaking into the room. The refrigerant gas itself is harmless, but it can
generate toxic gases when it contacts flames, such as fan and other heaters,
stoves and ranges.
When replacing the coin battery in the remote controller, be sure to disposed
of the old battery to prevent children from swallowing it.
If a child swallows the coin battery, see a doctor immediately.
Warning
Caution
Installation of a leakage breaker is necessary in some cases depending on the
conditions of the installation site, to prevent electrical shocks.
Do not install the equipment in a place where there is a possibility of
combustible gas leaks.
If a combustible gas leaks and remains around the unit, it can cause a fire.
Be sure to install the packing and seal on the installation frame properly.
If the packing and seal are not installed properly, water can enter the room and
wet the furniture and floor.
For integral units
only
Warning
Check to make sure that the power cable plug is not dirty or loose, then insert
the plug into a power outlet all the way.
If the plug has dust or loose connection, it can cause an electrical shock or fire.
If the power cable and lead wires have scratches or deteriorated, be sure to
replace them.
Damaged cable and wires can cause an electrical shock, excessive heat
generation or fire.
Do not use a joined power cable or extension cable, or share the same power
outlet with other electrical appliances, since it can cause an electrical shock,
excessive heat generation or fire.

SiE39-404 Introduction
ix
1.1.4 Using Icons
Icons are used to attract the attention of the reader to specific information. The meaning of each
icon is described in the table below:
1.1.5 Using Icons List
Caution
Check to see if the parts and wires are mounted and connected properly, and
if the connections at the soldered or crimped terminals are secure.
Improper installation and connections can cause excessive heat generation,
fire or an electrical shock.
If the installation platform or frame has corroded, replace it.
Corroded installation platform or frame can cause the unit to fall, resulting in
injury.
Check the grounding, and repair it if the equipment is not properly grounded.
Improper grounding can cause an electrical shock.
Be sure to measure the insulation resistance after the repair, and make sure
that the resistance is 1 Mohm or higher.
Faulty insulation can cause an electrical shock.
Be sure to check the drainage of the indoor unit after the repair.
Faulty drainage can cause the water to enter the room and wet the furniture
and floor.
Icon Type of
Information Description
Note:
Note A “note” provides information that is not indispensable, but may
nevertheless be valuable to the reader, such as tips and tricks.
Caution
Caution A “caution” isusedwhenthereis dangerthatthereader,through
incorrect manipulation, may damage equipment, loose data, get
an unexpected result or has to restart (part of) a procedure.
Warning
Warning A “warning” is used when there is danger of personal injury.
Reference A “reference” guides the reader to other places in this binder or
in this manual, where he/she will find additional information on a
specific topic.

Introduction SiE39-404
x
1.2 PREFACE
Thank you for your continued patronage of Daikin products.
This is the new service manual for Daikin's Year 2004 VRVII series Heat Pump System.
Daikin offers a wide range of models to respond to building and office air conditioning needs.
We are confident that customers will be able to find the models that best suit their needs.
This service manual contains information regarding the servicing of VRVII series Heat Pump
System.
There are some changes in piping and control system for products before December 2003.
Please refer the service information for product before December, 2003 to the service manual
Si39-302.
October, 2004
After Sales Service Division

SiE39-404
General Information 1
Part 1
General Information
1. Model Names of Indoor/Outdoor Units....................................................2
2. External Appearance...............................................................................3
2.1 Indoor Units..............................................................................................3
2.2 Outdoor Units...........................................................................................4
3. Combination of Outdoor Units.................................................................5
4. Model Selection......................................................................................6

Model Names of Indoor/Outdoor Units SiE39-404
2General Information
1. Model Names of Indoor/Outdoor Units
Indoor Units
Indoor Units (Connection Unit Series)
Note: BEV unit is required for each indoor unit.
Outdoor Units
Type Model Name Power Supply
Ceiling Mounted
Cassette Type
(Double Flow) FXCQ 20M 25M 32M 40M 50M 63M 80M — 125M — —
VE
Ceiling Mounted
Cassette Type
(Multi Flow) 600×600 FXZQ 20M 25M 32M 40M 50M — — — — — —
Ceiling Mounted
Cassette Type
(Multi Flow) FXFQ — 25M 32M 40M 50M 63M 80M 100M 125M — —
Ceiling Mounted
Cassette Corner Type FXKQ — 25M 32M 40M — 63M — — — — —
Slim Ceiling Mounted
Duct Type FXDQ 20N 25N 32N 40N 50N 63N — — — — —
Ceiling Mounted
Built-In Type FXSQ 20M 25M 32M 40M 50M 63M 80M 100M 125M — —
Ceiling Mounted
Duct Type FXMQ — — — 40M 50M 63M 80M 100M 125M 200M 250M
Ceiling Suspended
Type FXHQ — — 32M — — 63M — 100M — — —
Wall Mounted Type FXAQ 20M 25M 32M 40M 50M 63M — — — — —
Floor Standing Type FXLQ 20M 25M 32M 40M 50M 63M — — — — —
Concealed Floor
Standing Type FXNQ 20M 25M 32M 40M 50M 63M — — — — —
Outdoor Air Processing
Unit FXMQ-
MF ————————
125MF 200MF 250MF V1
Type Model Name Power Supply
Ceiling Suspended
Cassette Type FXUQ — — — — — — 71M 100M 125M — —
V1
Wall Mounted Type FXAQ-MH 20MH 25MH 32MH 40MH 50MH ——————
Floor Standing Type FXLQ-MH 20MH 25MH 32MH 40MH 50MH ——————
Connection Unit BEVQ-M 50M 50M 50M 50M 50M — 71M 100M 125M — — VE
Series Model Name Power Supply
Heat Pump RXYQ 5M 8M 10M 12M 14M 16M 18M 20M 22M 24M 26M Y1B
Series Model Name Power Supply
Heat Pump RXYQ 28M 30M 32M 34M 36M 38M 40M 42M 44M 46M 48M Y1B
VE: 1φ, 220~240V, 50Hz, 1φ, 220V, 60Hz
V1: 1φ, 220~240V, 50Hz
Y1B: 3φ, 380~415V, 50Hz

SiE39-404 External Appearance
General Information 3
2. External Appearance
2.1 Indoor Units
Ceiling Mounted Cassette Type (Double Flow)
FXCQ20M
FXCQ25M
FXCQ32M
FXCQ40M
FXCQ50M
FXCQ63M
FXCQ80M
FXCQ125M
Wall Mounted Type
FXAQ20M
FXAQ25M
FXAQ32M
FXAQ40M
FXAQ50M
FXAQ63M
Ceiling Mounted Cassette
Type (Multi Flow) 600×600
FXZQ20M
FXZQ25M
FXZQ32M
FXZQ40M
FXZQ50M
Floor Standing Type
FXLQ20M(H)
FXLQ25M(H)
FXLQ32M(H)
FXLQ40M(H)
FXLQ50M(H)
FXLQ63M(H)
Ceiling Mounted Cassette Type (Multi Flow)
FXFQ25M
FXFQ32M
FXFQ40M
FXFQ50M
FXFQ63M
FXFQ80M
FXFQ100M
FXFQ125M
Concealed Floor Standing Type
FXNQ20M
FXNQ25M
FXNQ32M
FXNQ40M
FXNQ50M
FXNQ63M
Ceiling Mounted Cassette Corner Type
FXKQ25M
FXKQ32M
FXKQ40M
FXKQ63M
New Ceiling Suspended Cassette Type
FXUQ71M
FXUQ100M
FXUQ125M
+
+
+
BEVQ71M
BEVQ100M
BEVQ125M
Connection Unit
Slim Ceiling Mounted Duct Type
FXDQ20N
FXDQ25N
FXDQ32N
FXDQ40N
FXDQ50N
FXDQ63N
Wall Mounted Type (Connection Unit Series)
FXAQ20MH
FXAQ25MH
FXAQ32MH
FXAQ40MH +BEVQ50M
FXAQ50MH
Ceiling Mounted Built-In Type
FXSQ20M
FXSQ25M
FXSQ32M
FXSQ40M
FXSQ50M
FXSQ63M
FXSQ80M
FXSQ100M
FXSQ125M
Floor Standing Type (Connection Unit Series)
FXLQ20MH
FXLQ25MH
FXLQ32MH
FXLQ40MH +BEVQ50M
FXLQ50MH
Ceiling Mounted Duct Type
FXMQ40M
FXMQ50M
FXMQ63M
FXMQ80M
FXMQ100M
FXMQ125M
FXMQ200M
FXMQ250M
FXMQ40~125M
FXMQ200 · 250M
Outdoor Air Processing Unit
Ceiling Suspended Type
FXHQ32M
FXHQ63M
FXHQ100M

External Appearance SiE39-404
4General Information
2.2 Outdoor Units
5HP 8,10HP 12,14,16HP
18, 20HP 22, 24, 26HP
28, 30, 32HP 34, 36HP
38, 40, 42HP 44, 46, 48HP
RXYQ5M RXYQ8M, 10M
RXYQ18M, 20M RXYQ22M, 24M, 26M
RXYQ28M, 30M , 32M RXYQ34M, 36M
RXYQ38M, 40M , 42M RXYQ44M, 46M, 48M
RXYQ12M, 14M, 16M

SiE39-404 Combination of Outdoor Units
General Information 5
3. Combination of Outdoor Units
Note: For multiple connection of 18HP systems or more, an optional Daikin outdoor unit multi
connection piping kit is required.
System
Capacity Number of units Module Outdoor Unit Multi Connection Piping Kit+Pipe
Size Reducer (Option)
5 8 10 12 14 16
5HP 1 l
—
8HP 1 l
10HP 1 l
12HP 1 l
14HP 1 l
16HP 1 l
18HP 2 ll Heat Pump: BHFP22M90+BHFP22M90P
20HP 2 ll
22HP 2 ll
24HP 2 ll
26HP 2 ll
28HP 2 ll
30HP 2 ll
32HP 2 ll
34HP 3 ll l Heat Pump: BHFP22M135+BHFP22M135P
36HP 3 ll l
38HP 3 ll l
40HP 3 lll
42HP 3 lll
44HP 3 lll
46HP 3 lll
48HP 3 lll

Model Selection SiE39-404
6General Information
4. Model Selection
VRV II Heat Pump Series
Connectable indoor units number and capacity
HP 5HP 8HP 10HP 12HP 14HP 16HP
System name RXYQ5M RXYQ8M RXYQ10M RXYQ12M RXYQ14M RXYQ16M
Outdoor unit 1 RXYQ5M RXYQ8M RXYQ10M RXYQ12M RXYQ14M RXYQ16M
Outdoor unit 2 – – – – – –
Outdoor unit 3 – – – – – –
Total number of connectable indoor units 8 13 16 19 20 20
Total capacity of connectable indoor units (kW) 7.0~18.2 11.2~29.1 14.0~36.4 16.8~43.6 20.0~52.0 22.5~58.5
HP 18HP 20HP 22HP 24HP 26HP 28HP
System name RXYQ18M RXYQ20M RXYQ22M RXYQ24M RXYQ26M RXYQ28M
Outdoor unit 1 RXYQ8M RXYQ10M RXYQ10M RXYQ10M RXYQ10M RXYQ12M
Outdoor unit 2 RXYQ10M RXYQ10M RXYQ12M RXYQ14M RXYQ16M RXYQ16M
Outdoor unit 3 – – – – – –
Total number of connectable indoor units 20 20 22 32 32 32
Total capacity of connectable indoor units (kW) 25.2~65.5 28.0~72.8 30.8~80.0 34.0~88.4 36.5~94.9 39.3~102.1
HP 30HP 32HP 34HP 36HP 38HP 40HP
System name RXYQ30M RXYQ32M RXYQ34M RXYQ36M RXYQ38M RXYQ40M
Outdoor unit 1 RXYQ14M RXYQ16M RXYQ10M RXYQ10M RXYQ10M RXYQ10M
Outdoor unit 2 RXYQ16M RXYQ16M RXYQ10M RXYQ10M RXYQ12M RXYQ14M
Outdoor unit 3 – – RXYQ14M RXYQ16M RXYQ16M RXYQ16M
Total number of connectable indoor units 32 32 34 36 38 40
Total capacity of connectable indoor units (kW) 42.5~110.5 45.0~117.0 48.0~124.8 50.5~131.3 53.3~138.5 56.5~146.9
HP 42HP 44HP 46HP 48HP
System name RXYQ42M RXYQ44M RXYQ46M RXYQ48M
Outdoor unit 1 RXYQ10M RXYQ12M RXYQ14M RXYQ16M
Outdoor unit 2 RXYQ16M RXYQ16M RXYQ16M RXYQ16M
Outdoor unit 3 RXYQ16M RXYQ16M RXYQ16M RXYQ16M
Total number of connectable indoor units 40 40 40 40
Total capacity of connectable indoor units (kW) 59.0~153.4 61.8~160.6 65.0~169.0 67.5~175.5

SiE39-404 Model Selection
General Information 7
Connectable Indoor Unit
Connectable Indoor Unit (Connection Unit Series)
Note: BEV unit is required for each indoor unit.
Indoor unit capacity
Use the above tables to determine the capacities of indoor units to be connected. Make sure the
total capacity of indoor units connected to each outdoor unit is within the specified value (kW).
The total capacity of connected indoor units must be within a range of 50 to 130% of the
rated capacity of the outdoor unit.
In some models, it is not possible to connect the maximum number of connectable indoor
units. Select models so the total capacity of connected indoor units conforms to the
specification.
Type Model Name Power Supply
Ceiling Mounted
Cassette Type
(Double Flow) FXCQ 20M 25M 32M 40M 50M 63M 80M — 125M — —
VE
Ceiling Mounted
Cassette Type
(Multi Flow) 600×600 FXZQ 20M 25M 32M 40M 50M — — — — — —
Ceiling Mounted
Cassette Type
(Multi Flow) FXFQ — 25M 32M 40M 50M 63M 80M 100M 125M — —
Ceiling Mounted
Cassette Corner Type FXKQ — 25M 32M 40M — 63M — — — — —
Slim Ceiling Mounted
Duct Type FXDQ 20N 25N 32N 40N 50N 63N — — — — —
Ceiling Mounted
Built-In Type FXSQ 20M 25M 32M 40M 50M 63M 80M 100M 125M — —
Ceiling Mounted
Duct Type FXMQ — — — 40M 50M 63M 80M 100M 125M 200M 250M
Ceiling Suspended
Type FXHQ — — 32M — — 63M — 100M — — —
Wall Mounted Type FXAQ 20M 25M 32M 40M 50M 63M — — — — —
Floor Standing Type FXLQ 20M 25M 32M 40M 50M 63M — — — — —
Concealed Floor
Standing Type FXNQ 20M 25M 32M 40M 50M 63M — — — — —
Outdoor Air Processing
Unit FXMQ-
MF ————————
125MF 200MF 250MF V1
Type Model Name Power Supply
Ceiling Suspended
Cassette Type FXUQ — — — — — — 71M 100M 125M — —
V1Wall Mounted Type
FXAQ-MH 20MH 25MH 32MH 40MH 50MH ——————
Floor Standing Type
FXLQ-MH 20MH 25MH 32MH 40MH 50MH ——————
Connection Unit BEVQ-M 50M 50M 50M 50M 50M — 71M 100M 125M — — VE
New refrigerant model code P20
type P25 type P32 type P40 type P50 type P63 type P80 type P100 type P125 type P200 type P250 type
Selecting model capacity 2.2
kW 2.8 kW 3.5 kW 4.5 kW 5.6 kW 7.0 kW 9.0 kW 11.2 kW 14.0 kW 22.4 kW 28.0 kW
Equivalent output 0.8HP 1HP 1.25HP 1.6HP 2.0HP 2.5HP 3.2HP 4HP 5HP 8HP 10HP

Model Selection SiE39-404
8General Information

SiE39-404
Specifications 9
Part 2
Specifications
1. Specifications........................................................................................10
1.1 Outdoor Units.........................................................................................10
1.2 Indoor Units............................................................................................21