Dakota Micro Overview DMOV-7MQ-C2 User manual

Dakota Micro, Inc.
8659 148½ Ave. SE
Cayuga, ND 58013
www.dakotamicro.com
Author: CNR Title: UserMan DMOV-7MQ-C2 Rev: 02/25/19
Quad View Monitoring System
Users Manual
Part Number: DMOV-7MQ-C2
www.dakotamicro.com
TROUBLESHOOTING
Problem Possible Causes
No picture, no sound Improper connection with 12v power adapter.
 Use of unauthorized power supply
Monitor is in OFF position
No picture Check whether AV cable is securely plugged in
No sound Check whether audio connector is secure
Check whether the sound volume is turned off or down
Dark picture Ensure that bright and contrast settings are properly
adjusted
Ensure monitor is warm enough
No color Ensure color settings are properly adjusted in menu
Upside down or lateral
inverted picture
Check horizontal/vertical adjustment on remote
Event Triggers not
activating (i.e. No
picture during triggered
event)
Event trigger is not securely connected
Remote Controller Fault Battery may be dead or improperly installed:
replacement battery Model:CR2025,3V
Remote controller is not pointed in the direction of the
receiving sensor on monitor
Too far away or improper angle: The maximum effective
distance between the remote controller and the receiving
sensor is 15 feet and the angle is 30 degrees.
Obstacle: Move any obstacles out of the path

LIMITED WARRANTY
• 7 inch LED backlit, high resolution TFT LCD screen is capable of displaying 4
cameras simultaneously
• Wide voltage input: 11-32V
• 4 Channel Inputs, displays 4 images simultaneously
• Manual image switching mode
• Forward/Mirror image selection
• Event Triggers provided for all 4 cameras. Cameras can be triggered for events such
as backing up or applying the brakes
• Power is provided only to the active camera, prolonging the life of the cameras
• Auto ON/OFF LED sensor automatically triggers night vision when required
• Includes credit card style remote control
• Backlit control buttons enable easy menu navigation in all lighting conditions
• Please read entire manual before using our products
• Before you power your rear OverView system, ensure that all cables are
properly connected to avoid damage to the system
• Monitor IS NOT WATERPROOF, please do not place the monitor outdoors
• Ensure that all cables are routed a sufficient distance from high temperature areas
and rotary objects
• To ensure proper heat dispersal, ensure that vent holes in monitor remain clear
• Do not open the monitor or camera casing, doing so will void the warranty
• DO NOT watch DVDs etc. while driving
• Please do not use caustic chemicals to wipe the camera and/or monitor
Subject to the disclaimer, limitations and other directions stated hereafter, Dakota Micro, Inc. warrants that the
Product will be free from defects in material and workmanship for periods as stated hereafter from the date of
original purchase. THIS WARRANTY IS EXPRESSLY MADE IN LIEU OF ANY AND ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS. THE
EXCLUSIVE REMEDY OF THE BUYER IS LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT.
EXCEPT AS STATED IN THIS WARRANTY, DAKOTA MICRO SHALL NOT BE LIABLE FOR ANY LOSS,
INCONVENIENCE, OR DAMAGE, INCLUDING DIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES, RESULTING FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER RESULTING
FROM BREACH OF WARRANTY, NEGLIGENCE, STRICT LIABILITY OF ANY OTHER LEGAL THEORY.
Any oral statements or representations made by anyone which are contrary to or at variance with the terms stated in this
LIMITED WARRANTY are void.
Dakota Micro will, at its option, either repair the defect or replace the defective Product or part thereof with a new
or remanufactured equivalent at no charge to the purchaser for parts or labor for the period of three (3) years for
AgCam/EnduraCam cameras, two (2) years for AgCam/EnduraCam monitors, quads and wireless,Twelve Months
(12) for all OverView Cameras & Monitors as well as all other cables and accessories.
The Dakota Micro limited warranty periods outlined above apply throughout the United States and Canada only.
A one (1) year maximum limited warranty for all Products applies to all other geographic locations unless
otherwise stated in writing by Dakota Micro.
This limited warranty does not apply to any issues connected with appearance that have no relation to the
performance of the Product nor t o any Product the exterior of which has been damaged or defaced, which has
been subjected to improper voltage or other misuse, abnormal service or handling, or which has been altered or
modified in design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the process set forth on
page 3 of this Policy, and provide proof of purchase to Dakota Micro.
Neither the sales personnel of Dakota Micro nor any dealer or any other person is authorized to make any
warranties other than those described herein, or to extend the duration of any warranties beyond the time periods
described herein.
The warranties described herein shall be the sole and exclusive warranties and remedies provided by Dakota Micro.
Correction of defects, in the manner and for the period of time described herein, shall constitute complete
fulfillment of all liabilities and responsibilities of Dakota Micro to the purchaser with respect to the Product, and
shall constitute full satisfaction of all claims. In no event shall Dakota Micro be liable or in any way responsible
for any damages or defects in the Product which were caused by repairs or attempted repairs performed by
anyone other than Dakota Micro.
Some states do not allow the limitation on or exclusion of incidental or consequential damages, so said limitation may
not apply to you.
Any action at law, suit in equity, or other judicial proceeding for the enforcement of any right provided for herein
or otherwise, or with respect to any claim that a purchaser may have against Dakota Micro shall be instituted only
in the Courts of the State of North Dakota, either in the state district court located in Wahpeton, North Dakota or
in Federal District Court location in Fargo, North Dakota. Without regard to conflicts of law principles, the laws of
the state of North Dakota shall govern the interpretation and enforcement of the terms of this Limited Warranty
and all aspects of the relationship between Dakota Micro and the purchaser.
This warranty gives you specific legal rights and you may also have other rights, which may vary from state to
state.
WARNINGS
WARNINGS
The OverView camera system is intended for light use and is not intended to be utilized in harsh
conditions such as high vibration, high moisture, and use in or around corrosive substances or
other high impact or corrosive situations. Should a heavy duty camera be required for your
application, an AgCam or EnduraCam camera from Dakota Micro should be utilized and is
warranted for this type of use. Warranty will be void on this system should it be utilized outside of
its recommended applications.
FEATURES

9 2
I. Monitor Introduction
Connection Chart
(Yellow)Video Output
(Red) Audio Output
①Left/Vol - ②Right/Vol + ③Menu ④Down/Back Cam Sel
⑤Up/Front Cam Sel ⑥Quad View Mode Switch ⑦ ON/OFF
Power/Video Harness
Connector with
screws
FUSE
(Green*) Trigger Cable for CAMF
(Blue*) Trigger Cable for CAMR
(White*)Trigger Cable for CAML
(Brown*)Trigger Cable for CAMB
12v power
CAM F (Black)
CAM B (Yellow)
CAM L (White)
CAM R (Red)
1) Cameras 1-4 have an available event trigger wire. Cameras are identified as F (Front), B (Back),
L ( L e f t ) a n d R ( R i g h t )
2) Regardless if monitor is ON or OFF, if power is applied to the trigger, activated camera will become
powered
3) Camera F has highest priority, camera R the lowest. Example: if both camera F and B are triggered
simultaneously, camera F will take precedence.
4) Peripheral DVR trigger cable
1. When the monitor is in quad view or front and back view, the cable has a DC12V output.
2. When the back trigger cable makes the monitor activated, the peripheral DVR trigger
cable has a DC12V output
* Event Trigger wire colors are subject to change without notice and may vary slightly from
the colors indicated above.
Monitor
Included Components
Monitor w/ bracket Monitor remote control Power/Video harness
x2 Camera(s) w/ bracket x2 40ft power/video cables 12v lighter adaptor
Screen Size
7” (16:9) digital panel
Overall Size
185mm(W)x124mm(H)x48(D) without mounting
bracket
Weight 400g
Power Input AC 10.5-16.9V, 1,200 ma (2 cameras)
Color System NTSC/PAL auto switch
Operating Temp -4°F~122°F (-20°C~50°C)
Brightness 400cd/m2
Resolution 800(RGB) x 480
Contrast 500:1
Number of Camera Inputs 4
⑦
①②③④⑤⑥

8
3
III. Installation of Power/Video Harness
V. Monitor Bracket Installation
Plug in securely and tighten screws
Monitor
Screw
Screw
IV. Install/Remove Sun Shade
Installation
Top Clip-buckle
Complete
Bottom Clip-buckle
Remove
Top Clip-buckle
Video System NTSC
Image Pick-up Device Sharp 1/3” Color CCD
Horizontal Resolution 600 Horizontal lines
Minimum Illumination 0 LUX @ F2.0
Viewing Angle 120 degree Field of View
Synchronous System Internal Synchronization
Operating Temp -4°F~122°F (-20°C~50°C)
Power Supply DC12v +/-10%
Waterproofing Criteria IP68K
Dimensions 74mm(W) x 55.5mm(D) x 63.5mm(H)

4
7
A
Trig C B
ON
ON
ON
ON
ON
ON
III. Button Function
MUTE
Press Mute to turn sound off， to resume volume, press Mute again or press VOL+.
POWER
Powers monitor ON and OFF.
UP/CAM
a. To select men u option.
b. To switch images in the mode of one camera view in order: B→L→R→F
VOL-/+
a. Adjust volume of monitor.
b. Adjust brightness, contrast, etc.
c. To activate other functions, such as, mirror/normal image switch, delay time
adjustment, etc.
MENU
Displays Monitor Main Menu.
MODE
User can use this key to select four mode s: standard color, soft color, rich color
and bright.
CALL
Press t his button is to display currently displayed AV channel.
TIMR
Time setup of sleep off, it is used to set the time off within 120 minutes.
C/E/P
Language selection: Choice of Chinese or English.
QUAD VIEW SWITCH
Turn monitor on; press Quad view mode s witch key, the quad view will be changed
in the order displayed below:
a. Picture:
b.Channel reverse setting:
c. Channel Switch：
L
R
LR
d. Trigger setting：
The default value of brightness, contrast and saturation is 50,
hue is 0.
The brightness, contrast and saturation value is between 0-100,
the hue value is between -5 ~ 5.
Set each channel image normal or mirror.
↑↓ Arrow Icons allows the image to be inverted.
There are 9 image display modes:
Single image (F, B, L, R)
Dual image (F/B, L/R)
Triplex image (B/L/R)
Quad image (田/H)
The six modes in the menu can be set on/off as required
Single image (B,F) and Dual image (F/B) modes are always on.
Each trigger wire can trigger any one of the 9 display modes.
Press this button to flip the picture horizontally.
Press this button to flip the picture vertically.
F( M- LR) B( M- LR)
L( M- LR) R( M- LR)
F( N- LR) B( N- LR)
L( N- LR) R( N- LR)
Monitor
Remote Control
F B L R
A
Trig C B
BRIGHTNESS
CONTRAST
SATURATION
HUE
VOLUME
50
50
50
0
50
A
Trig C B
FRONT
BACK
LEFT
RIGHT
N- LR
N- LR
N- LR
N- LR
A
C B Tri
g
Trig1
Trig2
Trig3
Trig4
T1 B
T2 L
T3 R
T4 F
F B
L R
L F R
B
LR
B

6
5
e. Reverse priority setting:
I. Introduction
The priority of the 4 triggers can be changed as request.
Priority1>Priority2>Priority3>Priority4
f. T-DELAY setting:
Default delay time for each CH is 0S, you can set the delay
time after trigger’s stopping.
Delay time can be set to (in seconds): 0S, 5S, 10S, 15S, 20S,
25S, 30S
Note: If the display mode is turned off, this setting is not
functional. During the trigger delay time, the keys do not
function.
g. System Setting:
Auto Bright:
ON: The display can automatically adjust the brightness
according to external environment
OFF: Auto bright function is OFF
Ruler Ref Line:
ON: The line always shows in the single CH image (B/L/R/F)
Trig: Only shows when the single CH (B/L/R/F) is triggered
OFF: No reference line
II. Replacing the Battery in your remote
h. Language
The reference line works only when there is a video signal
Input into the monitor,s or if the monitor is in multi image display
mode.
Pull Press
Battery Model:
(CR2025)
The default language is English,
Four languages are optional: English, Chinese, French, Deutsch.
Exit menu and save the settings
Remote Control
Monitor
A
C B Trig
Trig Priority 1
Trig Priority 2
Trig Priority 3
Trig Priority 4
T1 B
T2 L
T3 R
T4 F
A
Trig C B
LANGUAGE ENGLISH
A
C B
Trig
T1 B
T2 L
T3 R
T4 F
0s
0s
0s
0s
A
Trig C B
A
uto Bright
Ruler Line
ON
Trig
Mute ON/OFF
Up\CAM Selection
Volume-
Volume+
Menu
Down
Call
Mode
Slee p
Language
Quad View Mode Switch
Horizontal Flip Calendar
Vertical Flip