dams TGDMARM User manual

M4x12mm M5x12mm M6x12mm
E
10
5
3
46
7
8
9
10
11
1
902-9Kg
4
2
1
F
D
A B
/
12
23
32
!
3
5
6
C
4
7
8
9
1234
5
2
4
Installation guide B(8PCS) C(3PCS) D(16PCS) E(1PC) F(1PC)
4x4 5x5
A(8PCS) Allen Key Allen Key
1.Support arm (1PC)
2.Base Mounting Plate (1PC)
3.Protection pad (1PC)
4.Protection pad (1PC)
5.Perforated plate (1PC)
6.Long screw (1PC)
7.Protection pad (1PC)
8.Pressure plate (1PC)
9.Handwheel (1PC)
10.Mount Plate (2PCS)
11.Clip (2PCS)
STEP 1
The Preparation Before Monitor Installation
1.Make sure there are VESA holes 100x100mm or 75x75mm in the monitor. If not, cannot be installed.
2.Remove the original fixed base of monitor.Be careful not to scratch the screen.
75x75mm,100x100mm
STEP 2-A
Option1: Clamp
Tighten
For desk thickness:
20-30mm
DESK
Desktop
Caution
STEP 2-B Option2: Grommet
Notice: Keep the counterbore
side down
For desk thickness: 25-100mm
Tighten
Available hole size:8.5-70mm
Desktop
STEP 3
Connect the plate and monitor
monitor
Use washer if needed (D)
Use the allen key (F) to tighten the screw
Tighten
STEP 4
Install the monitor to the arm
Hang the monitor on the plate
from top to bottom and ensure
it is tightened
Connection plate
Lock
Item No.: TGDMARM
11C
E

3
F
12
F
11
Max:970
360°
75
100
±90°
102
±180°
±120°
±180°
±90°
-90°
15°
±120°
!
STEP 5 Adjust the monitor
Caution: Please do not fully
reverse the monitor screen-to
prevent damage to the fixings.
To adjust the swivel function by 5*5 allen key(F) on position 1
To adjust the tilt function by 5*5 allen key(F) on position 2
Adjust the Rotation Arm
STEP 6
When the size of monitors is small and the distance between the two monitors is too large,
the arms can be rotated to adjust the distance between the two monitors.
Cable Management
1. Take off cable management and put cable
management back to cover cables once
finishing the management
Cable
2. Buckle the clips (11) after
organising the cables.
Cable
Specification
CAUTION
This product contains small items that could be a choking hazard if swallowed. Keep these items away from young children.
● Make Sure these instructions are read and completely understood before attempting installation. If you are unsure of any part of this installation, please contact a professional
installer for assistance.
● The desk or mounting surface must be capable of supporting the combined weight of the mount and the display,otherwise the structure must be reinforced.
● Safety gear and proper tools must be used. A minimum of two people are required for this installation. Failure to use safety gear can result in property damage, serious injury or
death.
● please check joint parts every two months, making sure the screws are nor loosened.
This product was designed to be installed on a desk. Before installing, make sure the mount will support the combined load of the equipment and
hardware. Never exceed the maximum load capacity 9 KG, or else it may result in product failure or personal injury.
Note:this product is intended for indoor use only. Use of this product outdoors could lead to product failure or personal injury.
Warning:
obsolete products can be sent back to the manufacturer or handed over to professional institutions.
To maintain the gas mechanism in peak performance - it is suggested to raise the monitor arm up to the maximum height: ideally twice per month.
This product contains high pressure gas spring parts, please do not put it into fire, high temperature, or disassemble it, which will lead to
personal injury. The
Factory setting: 5-7KG
To equalise the mount and
monitor's weight-please