D&F DESIGN Adreanne User manual

1
Adreanne 4 pc Deep Seating Set
For questions or comments about product:
Email: s[email protected] or call our Customer Service
at:1-844-836-4055 (Monday-Friday, 9:30 am -5:30 pm Central time)

2
Safety Information
SET UP YOUR FURNITURE
PROPERLY
Ensure that all parts are assembled properly
and fully tightened as per the instructions.
When placing in the desired location, ensure
that all legs are resting on the same surface.
EXAMINE YOUR FURNITURE
Examine occasionally to ensure that there are
no loose parts. If loose parts are found,
they must be retightened fully before
additional use.
Warranty
1 YEAR WARRANTY FOR FRAME WICKER AND CUSHION.
WHAT IS COVERED
We warrant the frame to be free of manufacturing defects to the original purchaser for 1 year
WHAT IS NOT COVERED
□It remains the customer’s responsibility for freight and packaging charges to and from our service
center.
□This warranty does not cover commercial use, hardware, acts of nature, fire, freezing and abusive
use.
□Discoloration or fading of the finish or fabrics as a result of chemicals or spills is not covered.
□Glass table top breakage and corrosion or rusting of hardware are not covered.
□In addition, purchase parts are not covered under this warranty.
Care and Maintenance
□Do not allow water to build up in frames. This will cause corrosion and possible freezing damage
in cold climates.
□Use a mild soap and water for normal cleaning. DO NOT use janitorial or alcohol based cleaners.
Some cleaners may be marked as natural, but some ingredients can cause discoloration or have
adverse reaction to your finish.
□Rinse with clean water and dry with a soft, absorbent cloth towel.
□Cushions, slings, and/or an umbrella may be cleaned by hand with a solution of soap and water
with a clean water rinse. Never machine wash as this will result in shrinking or damage. After
cleaning, tip on end and allow to drip dry. Never use a commercial or home dryer to tumble dry
fabric goods.
□Treat frames with liquid wax for maximum protection against UV rays and /or salty, damp air.
□Use and operation: To prolong the life of your outdoor furniture, cover when not in use. Store
indoors during winter months.
CAUTION: Read all of the instructions in
this manual before you begin assembly.
Failure to do so may result in faulty
assembly and potential injury!

3
Pre-Assembly
PLANNING ASSEMBLY
PLEASE READ COMPLETE USE AND CARE GUIDE PRIOR TO ASSEMBLY!
Identify all parts packed in the carton against the parts list. Remove all protective materials and place
the parts on a nonabrasive surface to avoid scratching. It takes about 30 minutes for 1 person to
complete all the assembly.
OBSERVE WEIGHT LIMITS
The recommended weight limit for each item is listed below:
□Chair: 250 lbs
□Loveseat: 400lbs
□Table: 75lbs
HARDWARE INCLUDED
NOTE: Hardware not shown to actual
size.
___1___2___3___4
Part
Description
Quantity
1
M6X40mm Bolt
24
2
M6X30mm Bolt
14
3
Allen Wrench
1
4
M6 Washer
38
NOTE: More than one person may be
required to complete the assembly of this
product.

4
Pre-Assembly (continued)
PACKAGE CONTENTS
Part
Description
Quantity
A
Right Chair Armrest
3
B
Left Chair Armrest
3
C
Chair Seat
2
D
Chair Back
2
E
Loveseat Seat
1
F
Loveseat Back
1
G
Table Leg Panel
2
H
Table Side Panel
2
I
Glass Top
1
EVERY BOLT NEEDS TO BE USED WITH A WASHER.
DO NOT FULLY TIGHTEN BOLT UNTIL INDICATED IN STEP 1.
Safety Information
C
D
A
B
E
F
G
H
I

5
Assembly Instruction
-Chair
1
Attaching chair seat to the
chair back
NOTE: Do not fully tighten the bolts until all
have been positioned per assembly.
□Place chair back (D) on a flat, soft surface
□Attach chair seat (C) to the chair back (D) by using bolt (1) with metal washer (4) through the
hole of the chair seat into the chair back (D).
___1 ___4

6
Assembly Instruction
2
Attaching the chair back&seat
to the armrest
NOTE: Do not fully tighten the bolts until all
have been positioned per assembly.
□Insert the chair back (D) into the right armrest back leg (A), see the detail below.
□Attach the chair back (D) to the right armrest back leg (A) by inserting bolt (1) with metal
washer (4) through the hole of the chair back into the right armrest (A).
□Attach the chair seat (C) to the right armrest front leg (A) by inserting bolt (2) with metal
washer (4) through the hole of the chair seat into the right armrest (A).
□Attach the chair seat (C) to the right armrest (A) by inserting bolts (1) with metal washers (4)
through the other 2 holes of the chair seat into the right armrest (A).
□Repeat the steps above for left chair armrest.
___1 ___2 ___4

7
Assembly Instruction
3
Now is ready for your enjoyment.
.
□Tighten all bolts, put the seat cushion on the chair frame, your chair is now ready for use.

8
Assembly Instruction
1
Attaching loveseat seat to
the loveseat back
NOTE: Do not fully tighten the bolts until all
have been positioned per assembly.
□Place loveseat back (F) on a flat, soft surface
□Attach loveseat seat (E) to the loveseat back (F) by using bolts (1) with metal washers (4)
through each holes of the loveseat seat into the loveseat back (F).
___1 ___4
-Loveseat

9
Assembly Instruction
2
Attaching the loveseat
back&seat to the armrest
NOTE: Do not fully tighten the bolts until all
have been positioned per assembly.
□Insert the loveseat back (F) into the right armrest back leg (A), see the detail below.
□Attach the loveseat back (F) to the right armrest back leg (A) by inserting bolt (1) with metal
washer (4) through the hole of the loveseat back into the right armrest (A).
□Attach the loveseat seat (E) to the right armrest front leg (A) by inserting bolt (2) with metal
washer (4) through the hole of the loveseat seat into the right armrest (A).
□Attach the loveseat seat (E) to the right armrest (A) by inserting bolts (1) with metal washers
(4) through the other 2 holes of the loveseat seat into the right armrest (A).
□Repeat the steps above for left chair armrest.
___1 ___2 ___4

10
Assembly Instruction
3
Now is ready for your enjoyment.
.
□Tighten all bolts, put the seat cushion on the loveseat frame, your loveseat is now ready
for use.

11
Assembly Instruction
-Coffee table
1
Attaching table side panel to
the table leg panel
NOTE: Do not fully tighten the bolts until all
have been positioned per assembly.
□Place table leg panel(G) on a flat, soft surface
□Attach table side panel (H) to the table leg panel (G) by using bolts (2) with metal washers
(4) through each hole of the table side panel into the table leg panel (G).
___2 ___4

12
Assembly Instruction
2
Now is ready for your enjoyment.
.
□Tighten all bolts, put the glass top on the table frame, your table is now ready for use.
I