Daniels 844.BLU.PLOW User manual
3-IN-1 PLOW
Operator’s Manual
844.BLU.PLOW
(844.258.7569)
www.danielsplows.com
1
Recommended Wheel Loader Size
All 3in1 Sizes: 15,000 to 45,000 lbs
3-IN-1 PLOW
Operator’s Manual
Congratulations!
plowing equipment.
Before you begin . . .
IMPORTANT! – It is important to completely read and understand this owner’s manual
for your Daniels 3in1 Plow prior to installation and use. Failure to do so may adversely
affect the performance of your plow.
Prior to completing the installation process, make sure your loader meets all the requirements needed to
operate the Daniels 3in1 Plow. Your loader must also be equipped with an auxiliary hydraulic circuit (i.e., 3rd
Caution:
saws.
2
PLOW INSTALLATION
3-IN-1 PLOW
Operator’s Manual
IMPORTANT!
Check to be sure the 8” X 8” square tube (Throat Weldment) is
parallel to the pavement, as shown (Page 13, Diagram 2). When
be parallel to the pavement, create a visual reference point that
is visible from the loader cab by marking or painting a straight
line between the loader frame and the boom as shown (Page
13, Diagram 5). This will allow the operator to always return the
boom to the correct plowing position with the throat weldment
parallel to the pavement during use.
IMPORTANT!
For the easiest and safest shipping of
the Daniels 3in1 Plow the wings may
be bolted open. Check for and remove
this bolt prior to applying any hydraulic
pressure to the plow. The bolt is located
on the back side of the plow under both
wing cylinders. The bolt connects the
outer most rib of the center board section
of the 3in1 Plow to the inner most rib of
the wing section of the 3in1 Plow.
1. Connect the Daniels 3in1 Plow to the loader,
making sure the plow is securely locked in
place
2. Hydraulic hose installation
ports on the loader to the two empty ports on the
(Part #4) when routing the hoses. Make sure the
hoses will not be pinched when the plow is raised,
lowered, or hydro turned. Secure the two hoses
together with nylon zip ties as needed (Page 13,
appropriate length, raise the plow and roll the
hoses are not pulled or stretched during operation.
3
PLOW INSTALLATION
3-IN-1 PLOW
Operator’s Manual
3. Electric switch installation
harness has been pre assembled prior to shipping.
Prior to installing the electric wire harness and switch
by connecting the electrical connector plug to the
to the cab. Make sure the wire will not be pinched
when the plow is raised, lowered, or hydro turned.
Secure the wire with nylon zip ties as needed (Page
is not pulled or stretched during operation.
Use existing clamps along the boom arm or nylon zip
ties to secure the wire to the boom. Pay particular
lowered. Also, be sure to allow enough slack that
or movement between the machine body and the
electrical plug to the pre assembled plow harness at
installation process. Cover both connectors with
entering the electrical system.
a boot along the steering column, or through a hole
be drilled, select an area with no obstruction, on either
edges.
Install the black switch box in the cab. Install in a
that the switch box be mounted in a location which
machine. Use heavy duty two sided tape or a mounting
strap to mount the switch in the desired location.
to the installed switch. Keep the wire within the cab
routed behind the dash, wall, and door panels where
possible. Loose, exposed wire that is not properly
secured can be damaged or become tangled with the
white ground wire to a ground post or mounting screw
connectors are placed in a tool box or compartment
while the plow is installed on the machine. This will also
4
PLOW INSTALLATION
3-IN-1 PLOW
Operator’s Manual
4. Plow function cycle check
WARNING!
During ALL operations of the plow
during installation or plow use it is the
operators responsibility to make sure the
entire area around the machine and plow
are clear of obstacles and people. Failure
to do so can result in damage, injury, or
death.
WARNING!
blood poisoning and must be treated
by professional medical personnel
immediately.
WARNING!
Throughout the entire plow function
cycle check visually check for
hydraulic leaks.
Set the parking brake and start the machine. Raise
weldment level with the ground.
With the electrical switch in the middle “neutral”
and right until the plow moves smoothly in both
Return the plow to the straight position.
or right position. Using the 3rd valve control in
back. Repeat until the wing moves smoothly in both
directions. Move the electrical switch past neutral
to the opposite wing position. Using the 3rd valve
out and then back in. Repeat until the wing moves
smoothly in both directions.
hydraulic system. Consult the machine’s owners
oil levels, take some time to continue testing the
clearance needed as you angle the plow in many
straight position.
5
TRANSPORTING TO WORKSITE
To raise the plow, move the bucket lever to the “roll
back” position. This will cause the chains to tighten and
the plow to rise.
Always transport the Daniels 3in1 Plow with the wings
Always use the hazard and running lights and stay as
pilot vehicle may be required.
plow to the straight position with the wing hinges
perpendicular to the ground and the throat weldment
in the proper plowing position prior to use.
OPERATION
3-IN-1 PLOW
Operator’s Manual
WARNING!
Whenever folding the wings or angling
the blade make sure obstacles and
people are clear of the rotation area
cylinders.
IMPORTANT:
plow during normal operation. Position the loader boom so the throat weldment is parallel to the pavement
Diagram 5).
6
OPERATION
MAINTENANCE
make sure the cutting edge bolts and all hardware
are securely tightened and that all hydraulic lines are
secured and in good condition. Tighten or replace
periodically throughout the year. Make a visual check
bolts be checked and tightened as needed throughout
the plowing season.
3-IN-1 PLOW
Operator’s Manual
WARNING!
blood poisoning and must be treated
by professional medical personnel
immediately.
IMPORTANT:
position. The plow should only be raised when the blade is in the straight position. The standard swivel
Lower the plow in a slow and smooth motion. Dropping the plow may cause the cutting edge bolts to loosen
CAUTION!
Know the areas you are plowing!
Hitting manhole covers or other hidden
objects can cause property or equipment
damage as well as injury to the operator.
7
MAINTENANCE
The center wear edge, wing wear edges, and all wear items should be checked regularly and replaced
REMOVING THE PLOW
OFF SEASON STORAGE AND MAINTENANCE
It is recommended the Daniels 3in1 Plow be stored indoors. Connect the hydraulic couplers together and
exposed cylinder rods to inhibit corrosion.
3-IN-1 PLOW
Operator’s Manual
8
3-IN-1 PLOW Parts & Diagrams
9
3-IN-1 PLOW Parts & Diagrams
10
3-IN-1 PLOW Parts & Diagrams
11
3-IN-1 PLOW Parts & Diagrams
12
3-IN-1 PLOW Parts & Diagrams
PN17426
PN17428)-)2019+
-)2018-
13
3-IN-1 PLOW Parts & Diagrams
16
CORRECT
CORRECT
CORRECT
INCORRECT
INCORRECT INCORRECT
X
XX
14
at its sole and absolute discretion shall authorize its designated representative to repair or replace the
maintained in accordance with Daniels’ instructions, has not been subject to abuse or misuse, including but not
Daniels representative, has not been subject to any repair work or replacement parts not authorized in
writing by Daniels, and has not been used in any way other than its intended purpose. This warranty does not
apply to any “wear parts” such as cutting edges, springs, wear shoes and curb guards.
Daniels by purchase F.O.B. unless, in Daniels’ sole discretion, Daniels authorizes its designated representative
to repair or replace the part at the designated representative’s site. The snowplow or the applicable part
snowplow warranty or 30 days.
snowplow.
this warranty.
Daniels Plows, Inc. Warranty Information
844-BLU-PLOW www.danielsplows.com
Blue Plow LLC
1950 Manheim Rd. Melrose Park, IL 60160 USA
2959$Hart$Ct.$Franklin$Park,$IL$60131$USA
Daniels(Plows
PO(BOX(431(Hebron,(IL(60034(USA
15
Date Purchased:
Dealer Name / Address:
Model:
Serial Number:
Company Name: Owner:
Address: City: State:
Zip: Phone: Mobile:
FAX: Email:
Was this snowplow assembled and installed by the dealer? YES / NO
Was the owner’s manual included with the snowplow? YES / NO
Daniels Plows, Inc. Warranty Information
OR
please go to www.danielsplows.com/warranty to register.
844-BLU-PLOW www.danielsplows.com
Please mail completed form to:
Blue Plow LLC
1950 Manheim Rd. Melrose Park, IL 60160 USA
2959$Hart$Ct.$Franklin$Park,$IL$60131$USA
Daniels(Plows
PO(BOX(431(Hebron,(IL(60034(USA
This manual suits for next models
1
Table of contents
