Dante Glensound BEATRICE W1 Installation guide

BEATRICE
W1
Wall Mounted Network Audio Intercom
PRODUCT DETAILS
6 BROOKS PLACE, MAIDSTONE, KENT, ME14 1HE. ENGLAND. TEL: [phone]
Visit our Website at www.glensound.com FAX: [phone]

Page 2of 33
Glensound Electronics Ltd
Thank you for choosing a new Glensound product.
All rights reserved.
Information contained in this manual is subject to change without notice, if
in doubt please contact us for the latest product information.
If you need any help with the product then we can be contacted at:
Glensound Electronics Ltd
1 –6 Brooks Place
Maidstone
Kent
ME14 1HE
United Kingdom
Telephone: [phone]
Fax: [phone]
EMAIL ADDRESSES
General enquires: [e-mail]
Technical enquires: [e-mail]
Sales enquires: [e-mail]

Page 3of 33
PRODUCT WARRANTY:
All equipment is fully tested before dispatch and carefully designed to
provide you with trouble free use for many years.
We have a policy of supporting products for as long as possible and
guarantee to be able to support your product for a minimum of 10 years.
For a period of one year after the goods have been despatched the
Company will guarantee the goods against any defect developing after
proper use providing such defects arise solely from faulty materials or
workmanship and that the Customer shall return the goods to the
Company’s works or their local dealer.
All non-wear parts are guaranteed for 2 years after despatch and any
defect developing after proper use from faulty materials or workmanship
will be repaired under this warranty providing the Customer returns the
goods to the Company's works or their local dealer.

Page 4of 33
EU DECLARATION OF CONFORMITY FOR:
GS-BEATRICE W1
Wall mounted Dante/ AES67 intercom
This declaration of conformity is issued under the sole responsibility of
the manufacturer.
This equipment is manufactured by Glensound Electronics Ltd of Brooks
Place Maidstone Kent ME14 1HE is marked and conforms to the
following Union harmonisation legislation:
Low Voltage Directive: EN60065 and EN62368-1:2014
Emissions: BS EN55032:2015
Immunity: BS EN55035:2017
Signed for and on behalf of Glensound Electronics Ltd.
Gavin Davis, Managing Director
Maidstone, Kent, England
Date: 02/03/2020

Page 5of 33
RoHS DIRECTIVE
EC directive 2002/95/EC restricts the use of the hazardous substances
listed below in electrical and electronic equipment.
This product conforms to the above directive and for this purposes, the
maximum concentration values of the restricted substances by weight in
homogenous materials are:
Lead
0.1%
Mercury
0.1%
Hexavalent Chromium
0.1%
Polybrominated Biphenyls
0.1%
Polybrominated Diphenyl Ethers
0.1%
Cadmium
0.01%

Page 6of 33
WASTE ELECTRICAL AND ELECTRONIC
EQUIPMENT REGULATIONS 2006 (WEEE)
Glensound Electronics Ltd is registered for business to business sales of
WEEE in the UK our registration number is:
WEE/JJ0074UR

Page 7of 33
GLENSOUND BEATRICE W1
Handbook Contents
Issue 1
Description Page No.
Contents
PRODUCT WARRANTY:........................................................................................................................3
OVERVIEW.............................................................................................................................................8
W1 PANEL LAYOUT...............................................................................................................................9
Front & Rear Panels............................................................................................................................9
FEATURES.............................................................................................................................................9
CONFIGURATION MENU ....................................................................................................................12
FACTORY PRESETS ...........................................................................................................................19
AUDIO BLOCK DIAGRAM (analogue representation of digtal circuits) ...............................................20
CONNECTING THE BEATRICE W1 TO A DANTE NETWORK..........................................................21
Getting Dante Controller....................................................................................................................21
Connecting Beatrice To The Network ...............................................................................................21
Audio Over IP Network......................................................................................................................21
Running Dante Controller..................................................................................................................22
Dante Controller TIP..........................................................................................................................22
Device Not Showing Up In Dante Controller.....................................................................................23
AES67 MODE .......................................................................................................................................24
UPDATING FIRMWARE.......................................................................................................................27
UPDATING THE ULTIMO CHIPSET....................................................................................................32
WIRING INFORMATION.......................................................................................................................33
XLR & JACK Wiring...........................................................................................................................33

Page 8of 33
OVERVIEW
The BEATRICE range of IP intercoms was designed for broadcast, theatre and
professional audio applications.
Our Beatrice intercom system utilises the reliable and proven DanteTM network audio
transmission protocol to allow real time distribution of uncompressed audio across
standard networks. As such the BEATRICE units are also fully compatible with other
manufacturers’ equipment using the DanteTM protocol. The Beatrice W1 is also fully
AES67 compliant.
All units in the system are designed to be very easy to use for the operator and
simple to setup for the technician. They includes all the basic functionality required
for small intercom systems and none of the overly complex installation requirements
normally associated with large systems.
The name Beatrice was chosen for our intercom range as she was the love of Dante
Alighieri:
‘Dante had fallen in love with another, Beatrice Portinari (known as Bice),
whom he first met when he was only nine.’ Source Wikipedia.

Page 9of 33
W1 PANEL LAYOUT
Front & Rear Panels
FEATURES
1. Volume/ Setup Knob
This multi-function knob provides several different functions depending upon
whether the user is in setup mode or not.
In Normal Mode there are 3 functions:
A) Rotating the control increases / decreases the loudspeaker/ headphone
volume.
B) Simultaneously pushing the knob in and rotating it while pressing a speak
key will pan the associated incoming audio circuit between left/ right ears.
C) Simultaneously pressing a speak key and rotating the knob will increase /
decrease the input gain of the associated incoming circuit.
In Setup Mode:
The knob is used to enter menus and change parameters. This is done by
rotating the knob until the desired menu is seen on the display, then push the
Volume/ Setup Knob
Power On LED
Panel
Microphone
External
Microphone Input
Speak Key
Call Light
Audio Presence LED
Enter Setup

Page 10 of 33
knob and the menu will be accessed, rotate the knob again to select the
desired setting and press the knob in to select and save that setting.
2. Power On LED
The power on LED indicates that the device is powered on and the internal
microprocessor is working correctly.
3. Panel Microphone
The panel microphone is a small electret microphone fitted behind the front
panel and is suitable for most communications purposes.
4. External Microphone Input
This is a balanced microphone input. It can accept dynamic and condenser
microphones and phantom power (48v) can be turned on/ off in the menu
system. The gain of this input is also adjusted in the menu system.
5. Speak Key
These multifunction keys can operate in a number of different ways. In
general terms they route the output of the selected microphone to the
channels output. How they function i.e. Latching, Momentary or Intelligent can
be setup using the associated menu option.
Other functions are:
A) Double click (just like a pc mouse) will send a call signal to the connected
circuit and make the receivers call LED flash and also (if enabled) provide
an audio indication of an incoming call.
B) While simultaneously pressing the talk key and turning the volume/ setup
knob the input gain of the associated channel will be adjusted.
C) While simultaneously pressing the talk key and pushing and rotating the
volume/ setup knob the associated incoming circuit will be panned left/
right to the headphone output.
6. Call Light
This bright yellow LED will flash to indicate an incoming call on that circuit.
Pressing the speak key will automatically cancel the call light.
7. Audio Presence LED
The red audio presence LED indicates the presence of incoming audio on a
particular circuit. It has a threshold of approximately -20dB (so any lower level
audio will not trigger it) and it stays illuminated for 10 seconds after the
detected audio falls below the threshold.
8. Enter Setup Button
Pressing the small tactile switch will put the unit in setup mode. When in setup
mode the speak key will flash to clearly indicate that you are in setup mode.

Page 11 of 33
The setup mode is protected by a 2 digit passcode. The passcode is 45 (the
numeric equivalent of GL). Just turn the volume/ setup knob until 45 is shown
on the screen and then push the knob to select.
9. USB Update on side panel (Not pictured)
The USB connector is used for connected a PC to the device for loading
software updates.
10.Network RJ45 on side panel (Not pictured)
The Neutrik Ethercon network socket can connect to both Neutrik Ethercons
and standard RJ45 cables. It is a 100M/bit standard IP network connection.
The status LED flashes to show when data is being correctly communicated
with the attached switch. This connector is the PoE source for the unit.

Page 12 of 33
CONFIGURATION MENU
1. Entering/ Leaving Setup
To enter setup press the small round flush mounted button marked ‘SETUP’
Once in setup mode the talkback switch will flash to make it clear that you are in the
setup mode.
If no action is taken the unit will automatically exit setup mode after about 30
seconds of inactivity.
When in setup mode pressing the ‘SETUP’ button will exit the mode and the unit will
return to normal operation.
A. Unlock Code
To prevent operators entering the configuration menu and altering the device’s
settings when you first enter the setup mode the display asks for an unlock code.
To unlock the device rotate the Volume/ Setup knob until the number 45 is displayed
on the screen and then push the Volume/ Setup knob.
2. Selecting The Different Menus & Options Within The Menu
Once in setup mode with the device unlocked, rotate the Volume/ Setup knob to
scroll between the different menu settings. Once the display indicates the desired
menu that you would like to alter push the Volume/ Setup knob to enter that selected
sub menu.
Once in the sub menu, rotate the Volume/ Setup knob both clockwise and anti-
clockwise to display all available options for that parameter. When the setting that
you want to make is displayed on the screen push the Volume/ Setup knob and it will
then be set.

Page 13 of 33
B. Input Type
This setting allows the user to select either the internal microphone or the external
microphone to be used for talkback purposes. There are 2 options for the external
microphone to allow different types of microphones to be connected.
AVAILABLE OPTIONS:
Dynamic: External mic input for dynamic microphones
Phantom: External mic input with +48V Phantom Power being supplied
Panel: The Internal microphone mounted behind the front panel.
C. Input Gain
This adjusts the input gain of the microphone input and should be used to set the
output level of the user’s microphone to the intercom network.
The gain range is nominally marked 0 –30 for panel mic and 0 –17 for the external
mic.
To correctly set the gain, connect a microphone and set the appropriate input type,
enter the Input Gain menu and start talking into the microphone at the level that you
will use the unit. Next to the Gain level a very simple PPM will appear on the screen
made up of the characters >>>X<<< to indicate the audio level. The goal is to set the
level such that during normal speech the ‘X’ is on most the time and that you do not
get too many ‘<<’. If you don’t see the ‘X’ and only see ‘>>’ then you will need to turn
the gain up.

Page 14 of 33
D. Sidetone Vol
Sidetone is standard terminology for the user’s own voice appearing the user’s own
headphones. It has no effect on the outgoing level heard by other people on the
intercom network.
This setting adjusts the gain (volume) of the user’s own voice in their heaphone feed.
E. CH SW Mode
Setting the operation of the talkback key (button/ switche).
AVAILABLE OPTIONS:
Momentary: The talkback key must be held down to operate.
Latching: A push of the talkback key will turn the channel on, another push will then
turn the channel off.
Intelligent: A brief push of the talkback key will turn the channel on or off. But a
press and hold of the talkback key will only turn the output on (or off if already on)
while the key is being pressed.
F. CH Party Mode
Party mode is a facility that can be used to set up a party line style intercom. When
in party mode the Channel output has the incoming circuit routed and mixed in to it.

Page 15 of 33
G. Call mode
This mode provides the ability to turn off the calling feature. If you using the device in
a situation where the calling feature is not being used, then turning it off (disabling it)
can prevent accidental triggering of the call circuit.
Turning off the call mode turns off the transmitting of the call signal when a double
tap on the channels talk key is detected. It also turns of the detectors looking for an
incomming call signal.
H. RX Only mode
The receive only mode allows the device to receive audio only. When set in this
mode pressing the talk key turns the associated incoming audio circuit on/ off to the
loudspeaker/ headphones.
When a channel is set to receive only the operators microphone is never routed to
the channels output and a call signal will also never be sent to the output.
I. Headphone Boost
Headphone boost is a facility provided in case you are working in a very noisy
enviroment. By turning it on the headphone output level is increased by 10dB.
If ‘ON’ is not shown on the setup screen as per the above picture then headphone
boost is turned off.
J. Pip Tone Vol
HIGH HEADPHONE LEVELS CAN BE DANGEROUS
Please note high headphone output levels can seriously damage you hearing. Please consult your
health and safety officer to confirm a suitable and safe output level prior to using this equipment.

Page 16 of 33
Pip tone is the audio alert that a call has been received and is used to indicate to the
user that there is an incomming call.
The volume of this alert can be adjusted using this control.
K. LS dim Vol
LS (Loudspeaker) dim, is the amount of dimming that occurs on the front panel
loudspeaker when a talkback key is pressed. By dimming the loudspeaker when a
talkback channel is on you reduce the amount of acoustical pickup between the
loudspeaker and microphone which helps to eliminate nasty acoustical feedback.
L. End Stop Vol
The term ‘End stop’ refers to old fashioned electronic volume circuits where an ‘end
stop’ resistor would be placed at the bottom of a volume potentiometer to prevent
that potentiometer from fully attenuating (turning off) the audio signal.

Page 17 of 33
In the Beatrice units the incoming audio circuit has adjustable level control (to adjust
the incoming level of one circuit, press the associated talkback key and adjust the
Volume/ setup knob).
This ‘End stop’ menu adjusts the minimum level that the audio circuit can be set to,
where ‘0’ equates to off and ‘10’ equates to full volume.
M. Mute LS
Mute LS, this control is either on or off. It turns the front panel loudspeaker on or off.
N. Save Preset
There are 4 presets available. If you select a preset (1 –4) and push the volume/
setup knob then all the current settings will be saved to that position in non-volatile
memory. If there was a previously saved preset on the same preset number this will
be overwritten.
Please note the preset only saves configurations available via the menu system, it
does not save any Dante network information.
O. Load Preset
The load preset menu recalls previously saved configurations.

Page 18 of 33
P. Factory Reset
If the factory reset menu is entered and ‘Yes’ selected (and then the Volume/ Setup
knob is pushed) then the units configuration will return to factory defaults.
Please note factory reset will not overwrite any saved presets.

Page 19 of 33
FACTORY PRESETS
If the factory reset menu option is sleected the device will return to the following
parameters.
Please note that any saved presets are not affected by the factory reset operation.
hp_mix.rx1_gain = 15;
hp_mix.rx1_pan = 7;
hp_mix.sidetone_level = 7;
hp_mix.sidetone_pan = 7;
tx_channel_mix[0].button_mode = 2; //intelligent
tx_channel_mix[0].party_mode = 0;
hp_mix.pip_gain = 7;
hp_mix.master_gain = 15;
hp_mix.ls_dim_gain = 0;
hp_mix.rx_endstop_gain = 6;
ls_mix.ls_mute = 0;
mic_line.current_input_type = 0; //dynamic
mic_line.current_input_gain = 10;
mic_line.current_pwr_state = 0;
mic_line.phantom_gain = 10;
mic_line.dynamic_gain = 10;
mic_line.panel_mic_gain = 15;

Page 20 of 33
AUDIO BLOCK DIAGRAM (analogue representation of digtal
circuits)