Dante DFG480000 Frame User manual

DFG48000
Ethernet Managed Switch
Installation and Operations Manual
Model Number: DFG480000 Frame
DFG48044XEYRC
DFG48044XFYRC
DFG48G0 XEYRL
DFG48G0 4XEYRL
Description: Fiber Optic Ethernet Managed Switch

Table of contents DFG48000 Managed Fiber Switch Page
DFG48000 Managed Fiber Optic Switch 3
Hardware Installation and User Guide 3
Federal Communications Commission 3
1.0 SPECIFICA IONS 4
1.1 echnical Specifications 4
Operating Environment 5
Power Supply (Internal) 5
Agency Approvals 6
1. Ordering Information 6
DFG48000 Managed Fiber Switch, base unit 6
Configuration Options 6
2.0 IN RODUC ION 7
. Product Description – DFG48000 Managed Fiber Switch 7
. .1 DFG48000 and DFG48000R chassis 8
. .7 Four-Port 10 Mb MM Fiber ST Modules 9
. .8 Gigabit (1000Mbps) port modules 10
. .9 Packet Prioritization, 80 .1p QOS 11
. .10 Frame Buffering and Flow Control 11
. .11 Managed Network Software for DFG48000-Series 1
.3 Features and Benefits 1
Standard AC power input 100- 40VAC 1
DFG48000 licensed Network Management Software 1
.4 Applications 13
3.0 Installation 14
3.1 Locating DFG48000 Switches 14
3.2 Connecting Ethernet Media 15
3. . Connecting Fiber Optic SC-type, "Snap-In" 15
3. .3 Connecting Single-Mode Fiber Optic 15
3. .5 Connecting Twisted Pair (CAT5E or better) 15
3.3 able- op or Shelf Mounting 16
3.3.1 Rack-mounting 17
3.4 Powering the DFG48000 Managed Fiber Switch 18
3.4.1 Alarm Contacts for monitoring internal power, and Software Traps 18
3.5 DFG480XX (Port Module) Card Installation 18
3.5.1 Preparation for Installing and Removing DFG48000 19
3.6 Connecting the Console Terminal to DFG48000 (Management)
3.6.1 RS- 3 (DB-9) Console Com port (Serial port) pin assignments 3
4.0 OPERA ION 24
4.1 Switching Functionality 4
Address Learning 4
4. Status LEDs 4
4.3 Up-link MDI-MDIX on RJ-45 port modules, for port 1 only 4
4.4 Auto-Cross (MDIX) and Auto-negotiation, for RJ-45 ports 4
4.5 Flow-control, IEEE 80 .3x standard 5
5.0 Introduction - DFG48000 Managed Fiber Switch Port Modules 26
5. DFG480XX Card (Port Module) Description 6
5. .3 DFG48044EYRC 4@ 10/100Mbps RJ-45 Ports & @100Mbps single-mode FX-SC-type 0Km 8
5. .4 DFG48044FYRC 4@ 10/100Mbps RJ-45 Ports & @100Mbps single-mode FX-SC-type 40Km 8
5. .5 DFG48G0 4EYRL @ 10/100/1000Mbps RJ-45 & @100Mb single-mode FX, LC small form 9
5. .6 DFG48G0 EYRL @ 10/100/1000Mbps RJ-45 & 1@100Mb single-mode FX, LC small form 9
6.0 ROUBLESHOO ING 30
6.3 Return Material Authorization (RMA) Procedure 31
6.4 Shipping and Packaging Information 31
APPENDIX A: WARRAN Y INFORMA ION 31

Hardware
Installation and User Guide
DFG48000
Managed Fiber Optic Switch
Hardware
Installation and User Guide
rademarks
Ethernet is a trademark of Xerox Corporation
NEBS is a trademark of Telcordia Technologies
UL is a registered trademark of Underwriters Laboratories
Important: The DFG48000 Managed Fiber Switch contains no user serviceable parts. Attempted
service by unauthorized personnel shall render all warranties null and void. If problems are
experienced with DFG48000 Switch products, consult Section 6 - Troubleshooting, of this User
Guide.
Copyright © 007 Dante Security, Inc. All rights reserved. No part of this publication may be
reproduced without prior written permission from Dante Security, Inc.
Contacting Dante Security, Inc
Please use the mailing address, phone and fax numbers and email address listed below:
Dante Security, Inc.
1150 Broadway, suite 10
Hewlett, NY 11 34, USA
Phone [phone]
Website: http://www.dantesecurity.com
Email: [e-mail]
Federal Communications Commission
Radio Frequency Interference Statement
This equipment generates, uses and can radiate frequency energy and if
not installed and used properly, that is in strict accordance with the manufacturer's
instructions, may cause interference to radio communication. It has been tested
and found to comply with the limits for a Class A computing device in accordance
with the specifications in Subpart J of Part 15 of FCC rules, which are designed to
provide reasonable protection against such interference when operated in a
commercial environment. Operation of this equipment in a residential area is
likely to cause interference, in which case the user at his own expense will be
required to take whatever measures may be required to correct the interference.
Canadian Emission
This Class A digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil respecte toutes les exigences du Réglement sur le matériel du
Canada. Cet appareil est Classe A..

1.0 SPECIFICA IONS
1.1 echnical Specifications
Performance
Filtering / Forwarding Rate:
Ethernet: 14,880 pps
Fast Ethernet: 148,800 pps
Gigabit Ethernet: 1, 488,000 pps
Switching Processing Type: Store and Forward with IEEE 80 .3x full duplex
Flow -control, non-blocking
Data Rate: 10Mbps, 100Mbps and 1000Mbps
Address Table Capacity: 4K node, self-learning with address aging
Packet buffer size: 40KB for 10/100 and 1 0KB for 1000Mb
Latency: 5 µs + packet time (100 to 100Mbps)
15 µs + packet time (10 to 10 Mbps, and 10 to 100Mbps)
Network Standards and Compliance, hardware
Ethernet V1.0/V .0 IEEE 80 .3: 10BASE-T,
IEEE 80 .3u: 100Base-TX, 100BASE-FX
IEEE 80 .3z: 1000BASE-X Ethernet (Auto-negotiation)
IEEE 80 .3ab: 1000BASE-X Ethernet
IEEE 80 .1p: Priority protocol
IEEE 80 .1d: Spanning tree protocol
IEEE 80 .1w: Rapid Spanning tree protocol
IEEE 80 .1q: VLAN Tagging
IEEE 80 .3x: Flow Control
Maximum 10 Mbps Ethernet Segment Lengths
Unshielded twisted pair - 100 m (3 8 ft)
Shielded twisted pair - 150 m (49 ft)
10BASE-FL multi-mode fiber optic - km (6,56 ft)
10BASE-FL single-mode fiber optic - 10 km (3 ,810 ft)
Maximum Standard Fast Ethernet Segment Lengths:
10BASE-T (CAT 3, 4, 5 UTP) - 100 m (3 8 ft)
100BASE-TX (CAT 5 UTP) - 100 m (3 8 ft)
Shielded twisted pair - 150 m (49 ft)
100BASE-FX, half-duplex, multi-mode - 41 m (1350 ft)
100BASE-FX, full-duplex, multi-mode - .0 km (6,56 ft)
100BASE-FX, half-duplex, single-mode - 41 m (1350 ft)
100BASE-FX, full-duplex, single-mode - 0.0 km (66K 5 ft)
100BASE-FX, full-duplex, Long Reach - 40.0 km (1 K ft)
Maximum Standard Gigabit Ethernet Segment Lengths:
1000BASE-T (CAT5E or higher is recommended) - 100 m (3 8 ft)
1000BASE-SX, full-duplex, multi-mode (6 .5µm cable) - 0m
1000BASE-SX, full-duplex, multi-mode (50µm cable) - 550m
1000BASE-LX, full-duplex, single-mode (6 .5µm cable) -5Km

Fiber Multi-mode connector types supported:
Fiber Port, SC-type (snap-in): Fiber optic multi-mode, 100BASE-FX
Fiber Single-mode connector types:
Fiber Port, SC-type: Fiber optic single-mode, 100BASE-FX
Fiber Port, LC-type Fiber SFF single-mode, 100BASE-FX
LEDs: Per Port
LK: Steady ON when media link is operational
ACT: ON with receiver port activity
FDX/HDX: ON = Full-Duplex Mode
OFF = Half-Duplex Mode
100/10: ON = 100Mbps speed
OFF = 10 Mbps
Operating Environment
UL 60950 “Component Parts” temp. rating: 130° F (55°C)
IEC 60068 “Type Test” rating: -40°to 185°F (-40°to 85°C)
Storage: -40°to 185°F (-40°to 85°C)
Ambient Relative Humidity: 5% to 95% (non-condensing)
Altitude: - 00 to 13,000 ft. (-60 to 4000m)
Conformal Coating option on Z models
Packaging
Enclosure: Rugged High strength metal. Suitable for stand-alone
or rack-mounting
Dimensions: 1.70in. H x 17.0in. W x 9.0in. D
4.3 cm H x 43. cm W x .9cm D
Cooling method: Fan cooled, @ 3@ 7 cfm ea.
Management Console connector
DB-9 for RS- 3 “null-modem “cable (sometimes called an Xmodem cable)
Power Supply (Internal)
AC Power Connector: IEC-type, male recessed at rear of chassis,
with adjacent manual ON-OFF switch (on AC models only)
Input Voltage: 100 to 40 VAC (auto-ranging)
Input Frequency: 47 to 63 Hz (auto-ranging)
Power Consumption: 55 watts typical
60 watts max (for a fully loaded fiber model)
35 watts for a fully-loaded copper only model

Per-port MDI or MDIX on RJ-45 the copper daughter board has MDI-MDIX Auto-crossover on all the RJ-
45 ports and eliminate the use of cross-over cable between the devices. Also port specific user settings
(such as FDX or HDX, copper 10/100 speed) can be fixed using software commands. Alarm Contact
Optional) Alarm Contact option is offered as a configuration option. The two alarm contacts are SPST NC
Form-C relays, and an open condition indicates abnormal status. The Hardware Alarm monitors internal
power on the main board, and the Software Alarm is activated by one or more user-selected software
traps.
Agency Approvals
UL listed (UL60950), cUL, CE, Emissions meet FCC Part 15 Class A
NEBS Level 3 and ETSI Certified for Carrier Central Offices
IEEE 1613 Class Environmental Standard for Electric Power Substations
See also Note for Power Substations in Section 3. .4, 3.6.1, and 5. .9 IEC 61850 EMC and Operating
Conditions Class C for Power Substations
Warranty: Two years, return to factory Made in USA NEBS Testing and Certification: NEBS certified
1.2 Ordering Information
MODEL DESCRIPTION
DFG48000 Managed Fiber Switch, base unit
May be configured with a selection of 10/100/1000 DFG480XX fiber and copper port connector types.
Wire speed filtering and forwarding across all ports, 80 .3x flow control, 80 .1p priority packet
processing, self-learning 4K-node address table, large 40KB packet buffers for 10/100 and 1 0KB for
1000Mb. Plug-and-play switching services, front-mounted LEDs, internal auto-ranging AC power supply,
19" rack-mounting brackets. For licensed managed networks software, see MNS materials. DFG48000R:
“Reverse” model, same as Model DFG48000 except the user ports and the power input connectors are in
the rear. Two sets of LEDs (both rear and front) provide duplicate status data for viewing from either
side.
Configuration Options:
Each DFG48000 frame unit has four port module slots. The first three (A, B, C) may be one of the
modules DFG480XX below; one (slot D) may only be a Gigabit module DFG48G0XX. Select up to four
port modules per base unit.
DFG48044XEYRC Ethernet Switch 10/100Mbps 4 Copper, 4 Fiber Ports TRX 0Km SM SC
DFG48044XFYRC Ethernet Switch 10/100Mbps 4 Copper, 4 Fiber Ports TRX 40Km SM SC
DFG48G022XEYRL Ethernet Switch 10/100/1000Mbps Copper, Fiber Ports TRX 0Km SM LC
DFG48G024XFYRC Ethernet Switch 10/100/1000Mbps Copper, 4 Fiber Ports TRX 0Km SM LC
Y=-10°～+55C°, Z=-40°～+74C° (includes conformal coating)

2.0 IN RODUC ION
2.1 Inspecting the Package and Product
Examine the shipping container for obvious damage prior to installing this product; notify the carrier
of any damage that you believe occurred during shipment or delivery. Inspect the contents of this
package for any signs of damage and ensure that the items listed below are included. This package
should contain:
1 DFG48000 Managed Fiber Switch, base unit (configured with user-selected port module options)
1 AC Power Cord (U.S. only) 1 Set of metal “Ears” for 19” rack mounting 1 Installation and User
Guide (this manual) 1 Product Registration Card Remove the items from the shipping container. Be
sure to keep the shipping container should you need to re-ship the unit at a later date. To validate
the product warranty, please complete and return the enclosed Product Registration Card to Dante
Security, Inc. as soon as possible. In the event there are items missing or damaged, contact the
party from whom you purchased the product. If the unit needs to be returned, please use the original
shipping container if possible. Refer to Section 6, troubleshooting, for specific return procedures.
2.2 Product Description – DFG48000 Managed Fiber Switch
The DFG48000 Managed Fiber Switch boosts the performance of large Ethernet LANs, typically
serving as a “backbone” switch. It has the flexibility to handle a mix of both fiber and twisted-pair
switched ports along with Gigabit backbone port options. Industry-standard IEEE 80 .1p QOS
prioritization is included, providing high performance switching services for both “smooth” streaming
and “bursty” data traffic. The DFG48000 has up to 5 ports capacity, all of which may be configured
as fiber ports, but still offers a space-saving rack-mount chassis that is only 1U (1.70in. or 4.3 cm)
high. The “mixed-media” capability allows user selection of all popular flavors of fiber port connectors
and modes, including even 10 Mb fibers along with Gigabit ports. It also allows a mix of 10/100Mb
RJ-45 (copper) ports and a fiber Gigabit port in the same unit. This flexibility is achieved via a family
of DFG480XX port modules for copper and fiber-built-in (emphasizing Small Form Factor fiber for high
fiber port density), 6-port modules for fiber and RJ-45 combinations, and 1 GB port module selections
using GBICs. These modules can be factory configured in a base chassis unit (or may be changed in
the field by trained technicians) to adapt the unit to the user’s application and Ethernet cabling
requirements. Even evolving mixed-media requirements for 10Mb and 100Mb fiber and copper as well
as Gigabit ports can be handled by the DFG48000 product.
The chassis mounting rack style may be “regular” (with the ports and LEDs in the front and the power
input and management console connector in the rear) or “Reverse” (with the ports and LEDs and the
power-input and the management console connector all in the rear and a duplicate set of LEDs in the
front). Rack widths accommodated include standard 19” and input power may be AC. Designed for
use in network traffic centers, the DFG48000 Managed Fiber Switches are easy to install and use.
Addresses of attached nodes are automatically learned, maintained and aged out, adapting the
switching services to network changes. LEDs provide status information on each port. The DFG48000
provides high performance plug-and-play hardware operation, 80 .1p packet prioritization in
hardware, and industry-standard managed networks software functionality in convenient 1U rack-
mount packages.

\
2.2.1 DFG48000 and DFG48000R chassis
The DFG48000 is a 19” rack-mountable Ethernet Switch with three eight port slots (A, B, and C) and
one Gb-only slot (D) for configuration flexibility. Slots A, B and C may be configured with any of a
large selection of fiber and copper port types and combinations of types, typically eight ports per
module, but sometimes 6 or 4 ports or even one Gb port. Slot D may be configured with a Gb module
that accepts GBICs. The port types configurable using the 4 slots allows the DFG48000 to efficiently
serve a large variety of applications, especially using fiber media. The DFG480XX port modules are
normally factory installed, but may be changed or added in the field. (See Section 5)
Figure . .1a: “Regular” DFG48000 front view, configured for 4 + 1 GB ports Status LEDs are part
of each port module and are viewable when connecting the Ethernet media. A “regular” rack-mount
DFG48000 is shown in Figure . .1a. On “Reverse” rack-mount models, there is a duplicate set of
LEDs on the other (front) side for normal status viewing from that direction. Of course, with
management, the port status data is also available in software.

The DFG480XX Combo six-port modules are also available with 4@ MTRJ 100Mb mm SFF fiber and
@10Mb fiber mm ST ports, and with 4@ RJ45 10/100 copper and @10Mb fiber mm ST ports.
The 4@ RJ-45 + 2@ 10 Mb S operation of the SFF fiber and the RJ-45 half of the module is as
described for those port types above. For detailed information about 10Mb mm ST fiber half of the
module, please check section . .5.
2.2.7 Four-Port 10 Mb MM Fiber S Modules
The 4 port @10Mb ST fiber modules behave the same as the 8@100Mb ST fiber modules except
for the 10Mb speed. For ports numbering, ports 1, , 5, 6 are present, ports 3, 4. 7, 8 are not
present. The default setup on the 10Mb fiber module is half-duplex, which allows the DFG48000
Switch to connect to any 10Mb hub or media converter or almost any other device with a 10Mb
fiber Ethernet port. User mode control per port through the MNS software is the same as the
other DFG480XX modules. The fiber ports support fiber cabling distances according to the
10BASE-FL standard, i.e., km distance for multi-mode fiber. (Single-mode for up to 10Km
distance may be available as a special order configuration).

2.2.8 Gigabit (1000Mbps) port modules
The DFG48000 offered a wide option Gigabit speed with multiple choices for the modular slot.
While up to two Gigabit modules (maxm.) can be configured in the modular slot. The Gigabit port
option for the modular slot comes in couple of different configuration. The Giga port has been
offered as single Gigabit module comes in flavor of G+4(10/100 RJ-45 ports) or G+ (100Mb fiber
ports) as shown below. 1@ 1000Mb Fiber SC + @ 100Mb SC.