Dantel 41060 User manual

CAUTION
•Install or remove modules from the shelf only when the power is off.
If you install a module in the shelf with the power on, the internal
circuitry may suffer damage and the product warranty will be void.
•Remove and install circuit boards only in a static-safe environment
(use antistatic wrist straps, smocks, footwear, etc.).
•Keep circuit boards in their antistatic bags when they are not in use.
•Do not ship or store circuit boards near strong electrostatic, electromag-
netic, magnetic, or radioactive fields.
•For more complete information on electrostatic discharge safety
precautions, refer to BellcoreTM Technical Reference # TR-NWT-000870.
Copyright 2000 by Dantel, Inc. • Dantel is a registered trademark of Dantel, Inc. • ISO 9001 Registered
Printed in the U.S.A.
INSTALLATION & OPERATION MANUAL
41060-0400 <90-00052>
41060
WRITING SHELF
About this Practice:
This practice has been reissued to:
• Add the 41060-12 option.
Issue date: April 2000
Reissued Practices: Updated and
new content can be identified by a
banner in the right margin.
UPDATED
Table of Contents
Ordering Information ........................................................................... 2
General Description.............................................................................. 2
Installation............................................................................................ 3
Technical Specifications ....................................................................... 6
Warranty ............................................................................................... 8

PAGE 2 41060-0400 <90-00052>
NOTE: This section lists the different options available for this product. To order any of the avail-
able options, contact Dantel Inside Sales through our toll-free number, 1-800-432-6835.
OPTION NUMBER FEATURES
B25-41060-00 Writing Shelf, 19" width; Flush-mount
B25-41060-11 Writing Shelf, 23" width; Flush-mount
B25-41060-12 Writing Shelf, 23" width; Pre-configured for 5" extension
ORDERING INFORMATION
GENERAL DESCRIPTION
The 41060 Writing Shelf is available in two versions. The 41060-00 Writing Shelf mounts in a 19" equipment rack. The
41060-11 Writing Shelf mounts in a 23" equipment rack.
Both shelves are one rack unit high (1.75"). Each provides a
storage drawer, a writing surface, and a protected display space
for a drawing or data sheet.
The drawer can store meters, test leads, patch cords, jacks , and
plugs. It slides easily, without locking, for efficient use. The
drawer cover has a transparent plastic overlay for a smooth
writing surface. The overlay is also a protective cover for draw-
ings, telephone lists, or any document up to 11 x 17 inches.
The shelves have rounded corners to prevent snagging of cloth-
ing or skin.
The mounting brackets are adjustable so that you can install the
shelves
♦Flush with the equipment rack
♦Two inches forward from the equipment rack
♦Five inches forward from the equipment rack (standard
with -12 option)
The mounting brackets have 1" and 1.25" hole spacing for
installing the shelves in equipment racks.
NEW OPTIONUPDATED

41060-0400 <90-00052> PAGE 3
41060
Writing Shelf
Mounting Bracket Front
Rear
FRONT MOUNTING (Flush Mount Shown)
Equipment
Rack
To change the bracket locations:
1. On one side, extend the shelf slide as far as it will go.
2. Push down on the release lever (refer to Fig. 2) and separate the
slide from the shelf.
3. Move the inner part of the slide to expose one of the two screws
that hold the mounting bracket to the slide.
4. Remove the screw.
INSTALLATION
The 41060 can be mounted from the front (“Front Mounting”) of the rack or from the back (“Rear Mounting”) of the rack.
FRONT MOUNTING
The shelf comes with the mounting brackets installed for flush
mounting to the front of the equipment rack. Refer to Fig. 1.
FIG. 1 - FRONT MOUNTING, 41060
CONTINUED . . .

PAGE 4 41060-0400 <90-00052>
5. Move the inner part of the slide to expose the other screw.
6. Remove the screw.
7. Relocate the front of the bottom lip of the mounting bracket either
two inches or five inches back from the front of the slide.
8. Attach the bracket to the slide with the two screws.
9. Push the slide back onto the writing shelf.
10. Repeat the steps above for the mounting bracket on the other side
of the shelf.
To install the writing shelf:
Mount the shelf to the front of the equipment rack using the
hardware provided.
FIG. 2 - RELEASE LEVER LOCATION, 41060
Three section slide
Release lever
This end toward front
of writing shelf
REAR MOUNTING
The -00 and -11 options come with the mounting brackets
installed for flush mounting to the front of the equipment rack.
The -12 option comes factory set for a 5" extension to the front.
The following procedure allows you to remove the brackets and
reinstall them so you can mount the shelf to the rear of the
equipment rack. Refer to Fig. 3.
INSTALLATION
UPDATED

41060-0400 <90-00052> PAGE 5
41060
Writing Shelf
Mounting Bracket Front
Rear
REAR MOUNTING (Flush Mount Shown)
Equipment
Rack
FIG. 3 - REAR MOUNTING, 41060
To install the writing shelf:
1. On one side, extend the shelf slide as far as it will go.
2. Push down on the release lever (refer to Fig. 2) and separate the
slide from the shelf.
3. Move the inner part of the slide to expose one of the two screws
that hold the mounting bracket to the slide.
4. Remove the screw.
5. Move the inner part of the slide to expose the other screw.
6. Remove the screw.
7. Repeat the above steps for the mounting bracket on the other side
of the shelf.
8. Swap the mounting brackets so that the one that was on the left
slide is now on the right slide and the one that was on the right
slide is now on the left slide. This is necessary so that the bottom
lip of the mounting bracket is against the bottom of the slide. Also,
the holes for mounting the brackets to the equipment rack are now
at the rear of the slide.
CONTINUED . . .
INSTALLATION

PAGE 6 41060-0400 <90-00052>
9 Position the brackets on the slides for flush, two-inch, or five-inch
mounting.
10. Reinstall the screws.
11. Push the slides back on the writing shelf.
12. Mount the shelf to the rear of the equipment rack using the hard-
ware provided.
INSTALLATION
TECHNICAL SPECIFICATIONS
DESCRIPTION
DIMENSIONS
19"
23"WRITING SURFACE
19"
23" DRAWER SPACE
19"
23"
Loading
VALUE
19" x 12" x 1.75"
23" x 12" x 1.75"
17" x 11.25"
21" x 11.25"
16" x 11.5" x 1.4"
20" x 11.5" x 1.4"
50 lbs (fully extended)

41060-0400 <90-00052> PAGE 7
NOTES

PAGE 8
8 PAGES 41060-0400 <90-00052>
LIMITED WARRANTY
The Seller warrants that the standard hardware products sold will be free from defects in material and work-
manship and perform to the Seller’s applicable published specifications for a period of 18 months for hardware,
and 3 months for software, from the date of the original invoice. The liability of the Seller hereunder shall be
limited to replacing or repairing, at its option, any defective products which are returned F.O.B. to the Seller’s
plant, (or, at the Seller’s option, refunding the purchase price of such products). In no case are products to be
returned without first obtaining permission and a customer return authorization number from the Seller. In
no event shall the Seller be liable for any consequential or incidental damages.
Equipment or parts which have been subject to abuse, misuse, accident, alteration, neglect, unauthorized
repair or installation are not covered by warranty. The Seller shall make the final determination as to the
existence and cause of any alleged defect. No warranty is made with respect to custom equipment or products
produced to the Buyer’s specifications except as specifically stated in writing by the Seller in the contract for
such custom equipment.
This warranty is the only warranty made by the Seller with respect to the goods delivered hereunder, and may
be modified or amended only by a written instrument signed by a duly authorized officer of the Seller and
accepted by the Buyer.
Warranty and remedies on products not manufactured by the Seller are in accordance with warranty of the
respective manufacturer. THE SELLER MAKES NO OTHER WARRANTY OF ANY KIND WHATSOEVER,
EXPRESSED OR IMPLIED; AND ALL IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PUR-
POSE WHICH EXCEEDS THE AFORESAID OBLIGATIONS IS HEREBY DISCLAIMED BY THE SELLER.
INCASE OF DIFFICULTY
If you experience difficulty with this equipment, check the following, as appropriate:
1. Switch settings
2. Signal levels
3. Software configuration
4. Connections between Dantel’s equipment and your equipment.
If there is still a problem, substitute equipment that is known to be good. For additional assistance, call
Dantel’s Technical Field Service Department weekdays, 6 A.M. to 5 P.M. pacific time:
1-800-4DANTEL(1-800-432-6835).
If a thorough checkout shows a piece of equipment has malfunctioned, you may return it to the factory. For
repairs and emergency replacements, obtain a Return Material Authorization (RMA) number from the Cus-
tomer Service Representative at 1-800-4DANTEL (1-800-432-6835).
To ensure expedient processing of your order, provide a purchase order number and shipping and billing
information when requesting an RMA number. Also, when the units are returned to Dantel, include a descrip-
tion of the failure symptoms for each unit returned. Send defective equipment to:
Dantel, Inc. • 2991 North Argyle Avenue • Fresno, California 93727-1388
P.O. Box 55013 • Fresno, CA 93747-5013 Phone [phone] Fax [phone] http://www.dantel.com
WARRANTY