Danze PARMA D421058 User manual

®
Dual Kitchen Faucet
Grifo para cocina a
función doble
Robinet de cuisine à
fonction double
PARMA™
Model / Modelo / Modèle
Toll free service / Linea telefonica gratis / Numéro sans frais
D421058
Installation Instructions
Instrucciones para
la instalacion
Guide d'installation
US: 1-888-328-2383
Canada: 1-800-487-8372

Introduction
About your Faucet
Product Tour
®1
Congratulations on your purchase of the Danze Parma Dual Kitchen faucet with spray. This faucet
is designed to operate using the standard single control manual valve, or automatically without the
need to touch a faucet part to start and stop the faucet stream. The hands free mode delivers water
through the spout at a predetermined temperature, and will automatically shut off (you can set the
timing), by activating the sensor located on the spout. When you have greasy or dirty hands, now
you can start and stop the water without soiling the handle.
The guide is in English, Spanish and French languages for your convenience.
Before you begin , we recommend you review the installation steps as this faucet is unique.
Table of Contents
Check to make sure you have the following parts indicated below.
HINT: lay parts out on floor and connect all hoses loosely to understand arrangement before starting. If parts are missing, do not start this project. Call
service number for assistance.
PG
1
English section
Spanish section
French section
13
25
Green
Blue
Red
Yellow
Green
Blue
Orange
Orange
Brown
Red
Red
Green
Brown
Red Green
Yellow
• Operates hands-free or with single control handle
• Durable, smooth operating ceramic disc valve
• Brass vegetable spray
• AC or DC power
• Timed shut-off hands-free operation
• Includes hook-up hoses and fittings
• For DC hook-up: uses four C type batteries, not included
• Includes a step-by-step installation demonstration video in DVD format
© 2006 Danze, Inc. All rights reserved.

Operation Manual
Tools Required
Before you begin
®2
INSTALL SPOUT ASSEMBLY:
Place the spout into the hole of sink. The sensor window should be oriented to the
location best suited to the user to activate the faucet while limiting the possibility of
accidental activation. For double bowl sinks, often best location is directly over the sink
separation; for single bowl sinks, often best orientation is 45 degrees away from the
sink. Attach the rubber washer, plastic wire washer, metal washer and brass lock nut
to the spout shank. A protective film over the sensor window can be removed after
installation is complete.
NOTE: The rubber washer and plastic wire washer are designed to allow passage of
the wire. Insert properly to avoid pinching wires. Position carefully the wire washer,
slip up the flat washer and screw the lock nut until snug. Verify again for correct wire
clearance and tighten nut as required.
This faucet is designed to be installed in 1 1/2" diameter faucet mounting holes. Typical installation uses 3 mounting holes located 4" center to center
with the fittings mounted per the illustrations. Because the spout, hand valve, and spray are connected below the sink by hoses, you have flexibility to
locate these fittings in different order or location to suit the user. The hands free sensor should be oriented to avoid accidental triggering. See further
notes below.
Shut off main water supply before installation.
The power to the hands free mechanism can be supplied using battery pack (DC), or from your 110V household current (AC) using the power cord
with transformer supplied.
Adjustable wrench Channel lock plier Philips screwdriver C Style 1.5 Volt battery
1.
© 2006 Danze, Inc. All rights reserved.

®3
Install the "Y" adapter to the end of spout body shank.
2.
2. 3.1
3.2
INSTALL MANUAL VALVE ASSEMBLY:
3.1. Remove the hardware assembly from the base of the valve body.
3.2. Insert the valve body through the mounting hole. Secure the valve to the
countertop using the mounting hardware. Before tightening the handle
body, BE SURE that the lever handle is correctly centered left to right
between the hot and cold positions. A red/blue (hot/cold) self-adhesive
decal is included in your parts package; you can place it below the lever
on the handle if you choose.
3.
Hot Cold
Close
Open
25˚
45˚45˚
© 2006 Danze, Inc. All rights reserved.

®4
INSTALL VEGETABLE SPRAY ASSEMBLY:
4.
3.3
4.1 4.2 4.3
4.1. Remove plastic mounting lock nut from spray holder and insert
the spray holder from above into the mounting hole. Use lock nut
to securely attach to the sink.
4.2. Attach the spray hose to the spray head.
4.3. Insert spray hose through spray holder and install the hose
adapter to the brass tube labeled "For Spray Hose". Make sure
sprayer hose remains unobstructed and does not become tangled
with other hose beneath the sink.
3.3. Connect the hose adapter (marked ORANGE) to discharge
fitting (marked ORANGE) and the other end of hose (marked
BROWN) to Y adaptor(Marked BROWN). Tighten carefully.
Copper connections can be spread slightly to facilitate the
attachment and tightening of the hoses.
A
A
B
B
Brown marker
Orange marker
Discharge to spout (ORANGE) To vegetable spray
(labeled"For Spray Hose")
Water supply (BLUE)
(the long tube labeled
"For Hot Side")
© 2006 Danze, Inc. All rights reserved.

®5
CONNECT "T" ADAPTERS TO SUPPLY VALVES:
Install the "T" adapters onto the water supply stop valves from house.
5.
5.
6.
CONNECT WATER SUPPLY TO MANUAL CONTROL VALVE:
Install water supply hoses marked BLUE to hot and cold valve inlets in the
countertop mounted valve. Note: the connection should be "hot to hot" and "cold
to cold". Connect the other end of hoses to water supply stop valves marked
YELLOW.
6.
Water supply stop
valves from house
Blue Marker
Blue Marker
Yellow Marker
Yellow Marker
© 2006 Danze, Inc. All rights reserved.

®6
7.1 FOR AC POWERED OPERATION:
a. Remove the cover from sensor control box by using phillips
screwdriver. Take the rubber grommet with one hole out of the box.
Note: the "ON-OFF" switch should be turned to OFF (O) position
during installation.
b. Connect sensor lead from spout to sensor connection in box. Insert sensor
lead wire into the rubber grommet with one hole. Locate grommet between sensor
and connection. Reinstall it to the lower slot. Connect power supply wire from AC
adapter to power connection in box. Then install rubber grommet onto the upper
slot (all connections should be placed inside the box before replacing the lid).
c. Arrange the wires and connection in the sensor control box and reinstall
the cover. Plug AC adaptor to power supply (110VAC).
INSTALL SENSOR CONTROL BOX UNDER SINK:
Before installing the sensor control box, keep the following in mind: ensure it is
accessible so that it is not too difficult to turn it on/off, adjust the temperature and
change the battery. Verify that any shelving garbage can holders mounted on the
inside of doors, or other cupboard hardware will not interfere with the unit.
7.
7.1.a
7.1.b
7.1.c
Be sure to place wire
joints inside the box before
closing.
© 2006 Danze, Inc. All rights reserved.

®7
Select location on side wall of cabinet that will let
you easily service the battery pack and adjust the
temperature of the water. Position the sensor box
on wall. Attach sensor control box to wall with
mounting screws.
Note: Sensor control box should be mounted as
close to front of cabinet as possible for easy valve
adjustments and battery service.
7.2.a
7.2.b
7.2.c
8
8.
7.2 FOR DC POWER OPERATION:
a. Remove the cover from sensor control box by using
screwdriver. Take the rubber grommet with one hole
out of the box. Note: the "ON-OFF" switch should
be turned to OFF(O) position during installation.
b. Connect sensor lead from spout to sensor connection
in box. Insert sensor lead wire into the rubber
grommet with one hole. Locate grommet between
sensor and connection. Reinstall it to the lower slot.
Install the grommet without hole to the upper slot.
c. Install 4 1.5V "C'' sized alkaline batteries to make
sure the required battery polarity on battery holder.
Place the battery holder into the sensor control box.
Arrange wire and connection joint inside box, then
reinstall cover.
Wall
Grommet without hole
Be sure to place wire
joints inside the box
before closing.
© 2006 Danze, Inc. All rights reserved.

®8
10.
9
10
CONNECT HOSES TO SENSOR CONTROL BOX:
Connect supply hoses (marked green) to inlet
fittings (marked green) at mixing valve on control
box. Note: the connection should be "hot to hot"
and "cold to cold". Connect the spout connection
hose to the discharge port of the control box and to
the Y adapter (red to red).
After installing faucet, remove aerator and flush
the faucet to remove any leftover debris.
Reinstall the aerator.
9.
Cold
Hot
Cold
Hot
Red marker
Green marker
Green marker
Green marker Green marker
Red marker
© 2006 Danze, Inc. All rights reserved.

®9
Hands Free Operation
1. After the unit has been installed, before turning on the unit, make sure that there is no obstruction in directly in front of the sensor lens. Then turn it
on by pressing the ON-OFF switch on the control box to ON (I). Note: do NOT activate the waterflow until the led sensor light turns off ( for 10
seconds or so).
2. For hands-free operation, the waterflow can be turned on by placing a hand (or other object) briefly in front of the electronic sensor (within about
3”). The red indicator LED sensor light will blink and the waterflow will turn on and stay on for a factory-programmed 30 seconds.
3. If the user wishes to stop the waterflow, simply place a hand in front of the sensor a second time. Again, the LED sensor light will blink and the
waterflow will turn off.
Installation Diagram
Hands Free Sensor
Optional AC
Hand Control
Brass Vegetable Spray
Hands Free
Control Box
Hands Free
Hot/Cold Mixing Valve
© 2006 Danze, Inc. All rights reserved.