DAPAudio Odin CL-4 Connect User manual

Odin CL-4 Connect
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Product code: D3915
USER MANUAL
ENGLISH
V2

1
Odin CL-4 Connect
Product code: D3915
Preface
Thank you for purchasing this DAP product.
The purpose of this user manual is to provide instructions for the correct and safe use of this product.
Keep the user manual for future reference as it is an integral part of the product. The user manual shall be
stored at an easily accessible location.
This user manual contains information concerning:
●Safety instructions
●Installation and operation of the device
●Intended and non-intended use of the device
●Maintenance procedures
●Troubleshooting
●Transport, storage and disposal of the device
Non-observance of the instructions in this user manual may result in serious injuries and damage of
property.
©2022 DAP. All rights reserved.
No part of this document may be copied, published or otherwise reproduced without the prior written
consent of Highlite International.
Design and product specifications are subject to change without prior notice.
For the latest version of this document or other language versions, please visit our website
www.highlite.com or contact us at [e-mail].
Highlite International and its authorized service providers are not liable for any injury, damage, direct or
indirect loss, consequential or economic loss or any other loss arising from the use of, or inability to use or
reliance on the information contained in this document.

2
Odin CL-4 Connect
Product code: D3915
Table of contents
1. Introduction..........................................................................................................................................................3
Before Using the Product ..................................................................................................................................3
Intended Use .......................................................................................................................................................3
Text Conventions ................................................................................................................................................3
Symbols and Signal Words................................................................................................................................3
Symbols on the Information Label ..................................................................................................................4
2. Safety ....................................................................................................................................................................4
Warnings and Safety Instructions ....................................................................................................................4
Requirements for the User.................................................................................................................................6
3. Description of the Device ...................................................................................................................................6
Views.....................................................................................................................................................................6
Product Specifications ......................................................................................................................................7
Software ...............................................................................................................................................................7
Dimensions...........................................................................................................................................................8
4. Installation ............................................................................................................................................................8
Safety Instructions for Installation ....................................................................................................................8
Installation Site Requirements ..........................................................................................................................8
Connecting to Power Supply...........................................................................................................................8
5. Setup .....................................................................................................................................................................9
Connecting to a Computer via Wi-Fi .............................................................................................................9
Connecting to a Computer via LAN ..............................................................................................................9
Configuration via Web Browser.....................................................................................................................10
Mode Selection ......................................................................................................................................10
AP Interface Settings .............................................................................................................................11
STA Interface Settings ............................................................................................................................11
Application Settings ...............................................................................................................................12
Connecting Speaker Units..............................................................................................................................13
Network Setup Examples ................................................................................................................................14
Network Setup via Wi-Fi.........................................................................................................................14
Network Setup via LAN..........................................................................................................................15
Configuration Settings .......................................................................................................................15
Connecting the Software ...............................................................................................................................16
6. Troubleshooting .................................................................................................................................................17
7. Maintenance .....................................................................................................................................................17
Preventive Maintenance................................................................................................................................17
Basic Cleaning Instructions ...................................................................................................................17
Corrective Maintenance................................................................................................................................17
8. Deinstallation, Transportation and Storage ....................................................................................................18
9. Disposal ..............................................................................................................................................................18
10. Approval.............................................................................................................................................................18

3
Odin CL-4 Connect
Product code: D3915
1. Introduction
Before Using the Product
Important
Read and follow the instructions in this user manual before installing, operating or
servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual.
After unpacking, check the contents of the box. If any parts are missing or damaged, contact your
Highlite International dealer.
Your shipment includes:
●Odin CL-4 Connect
●AC power adapter
●User manual
Fig. 01
Intended Use
This device is intended for professional use as an Ethernet hub. It is suitable only for indoor use. It is not
suitable for households.
Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.
Text Conventions
Throughout the user manual the following text conventions are used:
●Buttons: All buttons are in bold lettering, for example “Press the UP/DOWN buttons”
●References: References to chapters and parts of the device are in bold lettering, for example:
“Refer to 2. Safety”, “press the power switch (03)”
●0–255: Defines a range of values
●Notes: Note: (in bold lettering) is followed by useful information or tips
Symbols and Signal Words
Safety notes and warnings are indicated throughout the user manual by safety signs.
Always follow the instructions provided in this user manual.
DANGER
Indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING
Indicates an imminently hazardous situation which, if not avoided, could result
in death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.

4
Odin CL-4 Connect
Product code: D3915
Attention
Indicates important information for the correct operation and use of the
product.
Important
Read and observe the instructions in this document.
Electrical hazard
Provides important information about the disposal of this product.
Symbols on the Information Label
This product is provided with an information label. The information label is located on the bottom plate of
the device.
The information label contains the following symbols:
This device shall not be treated as household waste.
Caution. Risk of electric shock. Do not open.
2. Safety
Important
Read and follow the instructions in this user manual before installing, operating or
servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual.
Warnings and Safety Instructions
DANGER
Danger for children
For adult use only. The device must be installed beyond the reach of children.
●Do not leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within
children’s reach. Packaging material is a potential source of danger for children.
DANGER
Electric shock caused by short-circuit
This device is delivered with an AC power adapter. Incorrect handling of the AC power adapter may
result in hazardous situations.
●Use only the AC power adapter delivered with the device.

5
Odin CL-4 Connect
Product code: D3915
●Do not wrap the power cable around the power adapter or any other object. This can damage the
internal wires.
●Do not cover the power adapter with anything when it is plugged into the socket-outlet. This may
cause overheating.
●Do not expose the power adapter to water or other liquids.
Do not use the power adapter:
●If it shows signs of overheating, for example the plastic is damaged
●If the AC input pins show signs of corrosion or overheating
●If the power cable is damaged or shows signs of material fatigue
Attention
Power supply
Before connecting the AC power adapter to the power supply, make sure that the current, voltage and
frequency match the input voltage, current and frequency specified on the information label on the AC
power adapter.
Attention
General safety
●Do not shake the device. Avoid brute force when installing or operating the device.
●If the device is exposed to extreme temperature variations (e.g. after transportation), do not switch it
on immediately. Let the device reach room temperature before switching it on, otherwise it may be
damaged by the formed condensation.
Attention
This device shall be used only for the purposes it is designed for.
This device is intended for professional use as an Ethernet hub. It is suitable only for indoor use. It is not
suitable for households. Any incorrect use may lead to hazardous situations and result in injuries and
material damage.
This device does not contain user-serviceable parts. Unauthorized modifications to the device will render
the warranty void. Such modifications may result in injuries and material damage.
Attention
Do not expose the device to conditions that exceed the rated IP class conditions.
This device is IP20 rated. IP (Ingress Protection) 20 class provides protection against solid objects greater
than 12 mm, such as fingers, and no protection against harmful ingress of water.

6
Odin CL-4 Connect
Product code: D3915
Requirements for the User
This product may be used by ordinary persons. Maintenance and installation may be carried by ordinary
persons. Service shall be carried out only by instructed or skilled persons. Contact your Highlite
International dealer for more information.
Instructed persons have been instructed and trained by a skilled person, or are supervised by a skilled
person, for specific tasks and work activities associated with the service of this product, so that they can
identify risks and take precautions to avoid them.
Skilled persons have training or experience, which enables them to recognize risks and to avoid hazards
associated with the service of this product.
Ordinary persons are all persons other than instructed persons and skilled persons. Ordinary persons
include not only users of the product but also any other persons that may have access to the device or
who may be in the vicinity of the device.
3. Description of the Device
The Odin CL-4 Connect is an Ethernet hub used to create a network between a computer and the Odin
Line Array System. The hub has 4 RC NET ports to which you can connect up to 12 Odin speaker units per
port and one uplink port to connect the device to a computer or a router. You can create a network via
the Wi-Fi or via LAN. The network allows you to configure the editable DSP presets of the Odin Line Array
System with the Odin CL-4 Editor software.
Views
Fig. 02
Antenna
LED indicators for ports 1–4
LAN connection LED indicator
Power LED indicator
05) DC connector, 5 V DC 1 A
06) RC NET ports 1–4 (RJ45 connectors)
07) LAN port (RJ45 connector)

7
Odin CL-4 Connect
Product code: D3915
Product Specifications
Model:
Odin CL-4 Connect
Electrical:
Input voltage:
5 V DC
Input current:
1 A
Power consumption:
5 W
Protection class:
Class III
Physical:
Dimensions:
197 x 135 x 46 mm (L x W x H), without the antenna
Weight:
1 kg (with the antenna)
Operation and control:
Control panel:
6 LED indicators
Display:
No
Wireless module:
2,4 GHz
Transmission rate:
57600 Bd
Connections:
Power connection:
DC connector IN
Uplink port:
1 x RJ45 LAN port with 2 built-in LED indicators
Network ports:
4 x RJ45 RC NET ports with 2 built-in LED indicators
AC power adapter:
Input voltage:
100–240 V AC, 50/60 Hz
Input current:
0,3 A
Output voltage:
5 V DC
Output current:
1 A
Protection class:
Class II
Construction:
Housing:
Metal
Color:
Black
IP rating:
IP20
Cooling:
Natural heat dissipation
Thermal:
Ambient temperature ta:
From -10 °C to 40 °C
Software
The Odin CL-4 Editor is a free software program developed by Highlite International. You can download
the software from the Odin CL-4 Connect product page on the website of Highlite International. The
software allows you to configure the editable DSP presets of the Odin Line Array System.
Product page for downloading the software and the user manual of the software: D3915

8
Odin CL-4 Connect
Product code: D3915
Dimensions
Fig. 03
4. Installation
Safety Instructions for Installation
Attention
Make sure there is enough space for ventilation around the device.
Do not install near equipment that produces heat, for example amplifiers.
Installation Site Requirements
●The device must be installed only indoors.
●The device can be placed on a flat surface.
●The maximum ambient temperature ta= 40 °C must never be exceeded.
●The relative humidity must not exceed 50 % with an ambient temperature of 40 °C.
Connecting to Power Supply
Attention
Incorrect handling of the AC power adapter may result in hazardous situations
This device is delivered with an AC power adapter. Incorrect handling of the AC power adapter may
result in hazardous situations.
●Connect the device to the socket-outlet with the delivered AC power adapter. Use only the AC
power adapter delivered with the device.
●Make sure that the socket-outlet is easily accessible.
●Disconnect the AC power adapter from the socket-outlet when the device is not in use.

9
Odin CL-4 Connect
Product code: D3915
5. Setup
Before setting up a network with the Odin CL-4 Connect you need first to configure the device. You can
connect the device via Wi-Fi or via LAN to a computer or a laptop and configure its settings via the web
browser.
Connecting to a Computer via Wi-Fi
The Odin CL-4 Connect can be connected to a computer, laptop, tablet or smartphone with a wireless
module.
To connect the device to a computer or a laptop via Wi-Fi, follow the steps below:
Power the device. See 4.3. Connecting to Power Supply on page 8 for more information. The power
LED indicator (04)will light up in red.
Put the antenna (01)in upright position.
Turn on the Wi-Fi on your computer or laptop.
Open the list with available Wi-Fi networks on your computer or laptop.
Select “ODIN CL-4” from the list.
Connect to “ODIN CL-4”. The password is “T-8A!Odin!S-18A”. To change the password refer to
5.3. Configuration via Web Browser on pages 10–12 for more information.
Note: If the device is reset to the default factory settings, the default SSID is “CL-4” and the default
password is “12345678”.
Fig. 04
Connecting to a Computer via LAN
To connect the device to a computer or a laptop via LAN, follow the steps below:
Use a UTP CAT-5/CAT-5E/CAT-6 cable to connect the LAN port (07)of the device to the RJ45 port on
your computer/laptop.
Power the device. See 4.3. Connecting to Power Supply on page 8 for more information. The power
LED indicator (04)will light up in red.
Assign a static IP address to your computer/laptop in the range 10.10.100.xxx with a Subnet mask
255.255.255.0.
Note: The default IP address of the device is 10.10.100.254.
Fig. 05