Davey D10A User manual

SUBMERSIBLE DRAINAGE PUMPS
Model Numbers: D10A, D15A, D25A,
D40A & D40M
PRODUCT
DESCRIPTION
Portable electric submersible
drainage pumps up to 400W
nominal output.
APPLICATIONS
• Dewatering of cellars, garages,
ditches, pits & ponds
• Pumping clean or slightly dirty
water
• Sump emptying
• Decorative water features
“A” suffix models equipped with
preset length float switch for
automatic operation
OPERATING LIMITSFEATURES & BENEFITS
Open impeller, centrifugal design
• Able to pump small soft solids
in suspension
• Less susceptible to blockage
Double mechanical shaft seal in
oil bath with hard faced silicon
carbide / ceramic seal on pump
side (D10 & D15 models have
single seals)
• Added motor protection
• Long service life
Sand slinger lip seal
• Added protection
• Long service life
Corrosive resistant 304 stainless
steel motor shell and strainer
• Long service life
• Attractive, lasting appearance
High quality paint finish
• Long service life
• Attractive lasting appearance
Automatic resetting thermal
overload
• Protected against overloading
HO7RNF oil resistant leads, 10
metres long with 3 pin power
plug
• Easy to connect to power
supply
• Longer life in dirty water
Capacities to 240lpm
Max. total head 12m
Max. submergence 10m
Max. operating
temperature 50oC
Suitable Fluids :
Sewage or “grey water” of neutral
pH containing up to 10% of small
soft organic solids (<10mm OD).
Some accelerated wear should be
expected while pumping hard solids
in suspension.
H/O & MFG SCORESBY
SUMP PUMPS

TECHNICAL SPECIFICATIONS
HYDRAULIC PERFORMANCEMATERIALS OF CONSTRUCTION
PART MATERIAL
Motor top
Pump body
Motor shell
Strainer
Impeller
Lip ring
Mechanical seal
Seal & bottom bearing
housing
Handle
Fasteners
Float & power supply leads
Polycarbonate (D10/15)
Cast iron (D25/40)
Cast iron
304 stainless steel
304 stainless steel
Polycarbonate (D10/15)
Cast iron (D25/40)
Nitrile
Silicon carbide/ceramic in oil
bath w/- oil seal
Carbon/ceramic on motor
side (D25/40)
Cast iron
304 stainless steel
304 stainless steel
H07RN-F oil resistant
ELECTRICAL DATA
INSTALLATION & PRIMING
Supply voltage / Hz 240/50Hz single phase
Cable length (m) 10
Output (watts) 100 150 250 400
Start (Amps) 6.0 9.0 12.0 10.5
Run (Amps) 1.0 1.5 2.2 3.7
Speed 2 pole, 2850rpm
Insulation class F
IP rating X8
Starting P.S.C.
0
5
10
15
0 100 200 300
FLOW
TOTAL HEADm
0
10
20
30
40
ft
Ipm
g/min 020 40 60
D40A
D25A
D15A
D10A
DIMENSIONS
This literature is not a complete guide to product usage. Further information is available from your Davey dealer, Davey Customer Service Centre and
from the relevant product Installation and Operating Instructions. This data sheet must be read in conjunction with the relevant product Installation
and Operating Instructions and all applicable statutory requirements. Product specifications may change without notice.
® Davey is a registered trademark of Davey Products Pty Ltd. © Davey Products Pty Ltd 1994.
D
E
A
B
C
All dimensions in mm unless otherwise stated.
Weight
Model A B C D E Outlet (kg)
D10A 300 60 160 115 260 11/4” F 5
D15A 320 60 160 115 260 11/4” F 5.5
D25A 370 85 225 145 290 11/2” F 9
D40A 430 85 225 145 290 2” F 11
Use a rope to position and retrieve the pump. Do not lower or retrieve the
pump using the power lead as this may damage the cable entry seals,
causing water leaks and unsafe operation.
Don’t use this product for recirculating or filtering swimming pools, spas, etc.
While these pumps are built to high safety standards, they are not approved
for installations where people will be in the water while they are operating.
Don’t pump abrasive materials. Sand and grit in the water being pumped
will accelerate wear, causing shortened pump life.
Keep your pump clean, particularly in situations where lint, hair or fibrous
materials may get bound around the pump shaft. Regular inspection and
cleaning will extend pump life.
Make room for the float switch to operate. Automatic models have a float
switch to turn them on when the water level rises and turn them off again
when it has been pumped down to the safe operating level of the pump. If
the float switch is not free to rise and fall, correct pump operation may not
be possible.
Don’t run your pump dry. Non-automatic models must be switched off
manually or by way of an external float/level switch when the water level is
reduced to the top of the pump housing.
Davey Products Pty Ltd
Member of the GUD Holdings Ltd Group
ABN 18 066 327 517
Head Office and Manufacturing
6 Lakeview Drive,
Scoresby, Australia 3179
Ph: [phone]
Fax: [phone]
Website: www.davey.com.au
Customer Service Centre
Ph: 1300 367 866
Fax: [phone]
E-mail: [e-mail]
Interstate Offices
Sydney - Brisbane - Adelaide
Perth - Townsville
International
6 Lakeview Drive,
Scoresby, Australia 3179
Ph: [phone]
Fax: [phone]
E-mail: [e-mail]
Germany
Kantstrasse 47,
04275 Leipzig
Ph: [phone]
Fax: [phone]
E-mail: [email protected]
New Zealand
2 Rothwell Avenue,
North Harbour, Auckland 1330
Ph: [phone]
Fax: [phone]
Website: www.daveynz.co.nz
E-mail: [email protected]
USA - Davey Pumps Inc.
1005 N. Commons Drive
Aurora, Illinois 60504
Ph: [phone]
Fax: [phone]
Website: www.daveyusa.com
E-mail: [email protected]
DPM142-1a/0806/WEB supersedes DPM142-1/3K/0706/SC