manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Davey
  6. •
  7. Water Pump
  8. •
  9. Davey X201 User manual

Davey X201 User manual

Trouble Shooting Check List
a) Motor runs when switched on but does not pump or pumps poorly
 1. Suctionlineandpumpbodynotlledwithwater.
2. Air leaks in suction lines or suction pipe not under water.
3. Air trapped in suction lines (due to uneven rise in piping; eliminate
humps and hollows).
4. No water at source or water level too low.
5. Valve on suction lines closed.
6. Check valve installed in wrong direction.
7. Suction lift too high.
8. Blocked impeller.
b) Motor doesn’t start when switched on
1. Power not connected.
2. Supply voltage too low.
3. “Over temperature” cut-out tripped.*
4. Motor not free to turn eg a jammed impeller.
5. Internal motor fault.
Priming and Operation
1. Fill the pump body with water at the priming hole adjacent to the delivery
outlet.
2. Replace priming plug and switch on.
3. Open gate valve in pump outlet to allow air from suction line to be expelled.
With long suction lines it may be necessary to reprime the pump more
than once.
4.Onceprimehasbeenestablishedastrongowofwateroutofthepump
willbeevident.Adjustvalvetorequiredowrate.
Spear Point Installations
The pumping capacity of your Dynaprime may need to be adjusted to match
the water supply available from your bore. This should be done by closing
thegatevalveinthepumpoutletuntiltheowtothesprinklersisequaltothe
water available to the spear point.
Be sure to choose the correct spear point to suit your water supply.
Installation and
Operating Instructions
for Dynaprime X201
Electric Pumps
Please pass these instructions on to the operator of this equipment.
Note:Forprotection,theDaveypumpmotoristtedwithan
automatic “over temperature” cut-out. Constant tripping of this
overloaddeviceindicatesaproblemeglowvoltageatpump,
motor overloaded.
Note:Ifthispumpisallowedtocontinuallypumpwater
containing sand or other abrasive material, the effective life of
thepumpwillbeshortened.
NOTE:Forprotection,theDaveypumpmotoristtedwithan
automatic reset thermal overload, constant tripping of this overload
indicatesaprobleme.g.lowvoltageatpump,excessivetemperature
(above 50°C) in pump enclosure.
WARNING:Automatic reset thermal overloads will allow the pump to
restartwithoutwarning.Always disconnectthepump motorfromthe
electrical supply before maintenance or repairs.
WARNING: Do not use hydrocarbon based or hydrocarbon propelled
sprays around the electrical components of this pump.
WARNING: When servicing or attending pump, always ensure power
is switched off and lead unplugged. Electrical connections should be
servicedonlybyqualiedpersons.
IMPORTANT: DONOTUSEpetroleumbaseduidsorsolvents
(e.g. Oils, Kerosene, Turpentine, Thinners, etc) on the plastic pump
components or seal components.
InaccordancewithAS3350.2.41weareobligedtoinformyouthatthispumpis
nottobeusedbychildrenorinrmpersonsandmustnotbeusedasatoyby
children.
Care should also be taken when servicing or disassembling pump to
avoidpossibleinjuryfromhotpressurisedwater.Unplugpump,relieve
pressurebyopeningataponthedischargesideofthepumpandallow
anyhotwaterinthepumptocoolbeforeattemptingtodismantle.
WARNING:Failuretofollowtheseinstructionsand
complywithallapplicablecodesmaycauseserious
bodily injury and/or property damage.
NOTE: Prior to installation remove the red transport
plugs & associated seals from the suction and/or
discharge ports.
Davey®Repair or Replacement Guarantee
In the unlikely event in Australia or New Zealand that this Davey product develops any malfunction within two years of the date of original purchase due to
faulty materials or manufacture, Davey will at our option repair or replace it for you free of charge, subject to the conditions below.
Should you experience any diculties with your Davey product, we suggest in the rst instance that you contact the Davey Dealer from which you
purchased the Davey product. Alternatively you can phone our Customer Service line on 1300 367 866 in Australia, or 0800 654 333 in New Zealand, or
send a written letter to Davey at the address listed below. On receipt of your claim, Davey will seek to resolve your diculties or, if the product is faulty or
defective, advise you on how to have your Davey product repaired, obtain a replacement or a refund.
Your Davey Two Year Guarantee naturally does not cover normal wear or tear, replacement of product consumables (i.e. mechanical seals, bearings or
capacitors), loss or damage resulting from misuse or negligent handling, improper use for which the product was not designed or advertised, failure to
properly follow the provided installation and operating instructions, failure to carry out maintenance, corrosive or abrasive water or other liquid, lightning
or high voltage spikes, or unauthorized persons attempting repairs. Where applicable, your Davey product must only be connected to the voltage shown
on the nameplate.
Your Davey Two Year Guarantee does not cover freight or any other costs incurred in making a claim. Please retain your receipt as proof of purchase; you
MUST
provide evidence of the date of original purchase when claiming under the Davey Two Year Guarantee.
Davey shall not be liable for any loss of prots or any consequential, indirect or special loss, damage or injury of any kind whatsoever arising directly
or indirectly from Davey products. This limitation does not apply to any liability of Davey for failure to comply with a consumer guarantee applicable to
your Davey product under the Australian or New Zealand legislation and does not aect any rights or remedies that may be available to you under the
Australian or New Zealand Consumer Legislation.
In Australia, you are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Should your Davey product require repair or service after the guarantee period; contact your nearest Davey Dealer or phone the Davey Customer Service
Centre on the number listed below.
For a complete list of Davey Dealers visit our website (davey.com.au) or call:
* Installation and operating instructions are included with the product when purchased new.
They may also be found on our website.
AUSTRALIA
Customer Service Centre
6 Lakeview Drive,
Scoresby, Australia 3179
Ph: 1300 232 839
Fax: 1300 369 119
Email: [email protected]
Website: davey.com.au
Davey Water Products Pty Ltd
Member of the GUD Group
ABN 18 066 327 517
NEW ZEALAND
Customer Service Centre
7 Rockridge Avenue,
Penrose, Auckland 1061
Ph: 0800 654 333
Fax: 0800 654 334
Email: [email protected]
Website: daveynz.co.nz
® Davey is a registered trademark of Davey Water Products Pty Ltd. © Davey Water Products Pty Ltd 2016. P/N 47727-7
47727-7_Dynaprime_X201_I&OI.indd 1 12/12/2016 3:35 PM
Spear Point Installations
When installing a Dynaprime on a
spear or well point as (A) right, a check
valve immediately above the spear will
greatly assist pump operation (when re-
priming).
The Pump may require “topping-up”
with water at initial priming after the
trapped air in the suction pipe between
pump and water level is pumped out.
Housing your Pump
To protect your pump from the weather, make sure the cover provided is both
water proof, frost free and has adequate ventilation.
Thepumpshouldbehorizontallymountedonarmdrybaseallowingfor
drainage,toavoiddamagetoooring
Connect lead to power supply designated on pump label, do not use
long extension leads as they cause substantial voltage drop, poor pump
performance and may cause motor overload.
Type of Piping to be used
It is recommended that polythene piping be used for the pump suction and the
delivery lines immediately adjacent to the pump. PVC piping may be used as
an alternative to polythene pipe, however, unions should be used with PVC
pipe so that the pump may be removed without cutting the piping.
Connection to your Water source
As your Davey Dynaprime pump has an inbuilt check valve, no external check
valve or foot valve is required. (On some suction lifts it may be advisable to
tafootvalvetoassistwithpriming.Withafootvalveinstalledatthebottom
ofthesuctionpipe,itmaybebenecialtoincorporatea“primingtee”inthe
suction pipework adjacent to the pump to aid in initial priming of the suction
line).
Installation of a suction strainer is recommended to prevent large items of
foreignmatterenteringthepump.Thesuctionstrainershouldhavesufcient
areasoastonotrestrictthewaterowtothepump.Ensurethatthestrainer
on the end of the suction pipe does not rest in debris or mud at the bottom of
your water source as (B) opposite.
Suction Piping
Suction piping should be laid so there is a constant rise from the water source
to the pump. Any high spots will cause pockets of air to form which may
reducetheefciencyofthesystem.Forbestperformanceusepipeofatleast
the same diameter as the pump’s inlet.
Choosing a Site
Chooseasitewitharmbaseandasclosetothewatersourceaspossible
with correct power supply. Make sure your Dynaprime pump is always
connected to an adequate, reliable source of water.
ConnectionofOutletPipeworktoPump
Tocontroltheowofwaterfromthepumpitisrecommendedthatagatevalve
be installed on the pump outlet - this is particularly advisable when there is a
possibility of the pump delivering water at a faster rate than may be available at
the source (e.g. spear point, spring, well etc.). Use thread tape at all times and
donotover-tightenttings.Forbestperformanceusepipeofatleastthesame
diameter as the pump outlet.
Prior to using this pump you must ensure that:
• The pump is installed in a safe and dry environment
• The pump enclosure has adequate drainage in the event of leakage
• Any transport plugs are removed
• The pipe-work is correctly sealed and supported
• The pump is primed correctly
• The power supply is correctly connected
• All steps have been taken for safe operation
Appropriate details for all of these items are contained in the following
Installation and Operating Instructions. Read these in their entirety before
switching on this pump. If you are uncertain as to any of these Installation and
Operating Instructions please contact your Davey dealer or the appropriate
Daveyofceaslistedonthebackofthisdocument.
Congratulations on your purchase of a high quality, Australian built Davey
pump. All components have been designed and manufactured to give trouble
free, reliable operation.
DYNAPRIMEX201
1. Priming Plug
2. Drain Plug
3. Suction Inlet (11/4” BSPF)
4. Pump Body
5. Delivery Outlet (11/4” BSPF)
6. Motor
Beforeinstallingyournewpump,pleasereadallinstructionscarefullyasfailurescausedby
incorrect installation or operation are not covered by the guarantee. Your Dynaprime X201
is designed to handle water containing soft solids to 10mm. It should not be used for any
otherpurposewithoutspecicreferraltoDavey.Theuseofthepumptohandleammable,
corrosiveandothermaterialsofahazardousnatureisspecicallyexcluded.
Do not use pipe thread sealing compound on any part of this
pump.ONLYuseteonthreadsealingtape.
 WARNING:Someinsects,suchassmallants,ndelectricaldevices
attractive for various reasons. If your pump enclosure is susceptible
to insect infestation you should implement a suitable pest control plan.
PowerConnectionsandWiringmustbe
carried out by an authorised electrician.
Note: Suction leaks are the largest cause of poor pump
performanceandaredifculttodetect.Ensureallconnections
are completely sealed using thread tape only.
47727-7_Dynaprime_X201_I&OI.indd 2 12/12/2016 3:35 PM

Other Davey Water Pump manuals

Davey Dynapond 7000 User manual

Davey

Davey Dynapond 7000 User manual

Davey Spa Power SP800 User manual

Davey

Davey Spa Power SP800 User manual

Davey SureFlo DSF750 User manual

Davey

Davey SureFlo DSF750 User manual

Davey AS Series User manual

Davey

Davey AS Series User manual

Davey PowerMaster 250 User manual

Davey

Davey PowerMaster 250 User manual

Davey QB Series User manual

Davey

Davey QB Series User manual

Davey HS50-06 User manual

Davey

Davey HS50-06 User manual

Davey DC10 User manual

Davey

Davey DC10 User manual

Davey TotalFlo TF40J User manual

Davey

Davey TotalFlo TF40J User manual

Davey jumbo floodfighter User manual

Davey

Davey jumbo floodfighter User manual

Davey DynaDrive DD60-10 User manual

Davey

Davey DynaDrive DD60-10 User manual

Davey HM Series User manual

Davey

Davey HM Series User manual

Davey PowerMaster Eco PMECO User manual

Davey

Davey PowerMaster Eco PMECO User manual

Davey JY Series User manual

Davey

Davey JY Series User manual

Davey DynaDrive DD60-10 User manual

Davey

Davey DynaDrive DD60-10 User manual

Davey RainBank Evolution MkII User manual

Davey

Davey RainBank Evolution MkII User manual

Davey TotalFlo TF117MS User manual

Davey

Davey TotalFlo TF117MS User manual

Davey E1P Series User manual

Davey

Davey E1P Series User manual

Davey CD40-40 User manual

Davey

Davey CD40-40 User manual

Davey SJ35-04 Manual

Davey

Davey SJ35-04 Manual

Davey 6200 User manual

Davey

Davey 6200 User manual

Davey XP500H User manual

Davey

Davey XP500H User manual

Davey HM Series User manual

Davey

Davey HM Series User manual

Davey Weekender XP User manual

Davey

Davey Weekender XP User manual

Popular Water Pump manuals by other brands

Briggs & Stratton 73021 Operator's manual

Briggs & Stratton

Briggs & Stratton 73021 Operator's manual

Holmatro 363 manual

Holmatro

Holmatro 363 manual

Ironton 60729 owner's manual

Ironton

Ironton 60729 owner's manual

Ingersoll-Rand ARO AF0813S Series Operator's manual

Ingersoll-Rand

Ingersoll-Rand ARO AF0813S Series Operator's manual

Franklin Electric VersaJet Series Installation and operation manual

Franklin Electric

Franklin Electric VersaJet Series Installation and operation manual

Neptun NCHW-E 110 Inox Original operating instructions

Neptun

Neptun NCHW-E 110 Inox Original operating instructions

Bosworth Guzzler G2-0501N Operator's manual

Bosworth

Bosworth Guzzler G2-0501N Operator's manual

Grundfos UPS 15-30 130 instructions

Grundfos

Grundfos UPS 15-30 130 instructions

Conel FLOW TPF Installation and operation instruction

Conel

Conel FLOW TPF Installation and operation instruction

Bosch 0 986 580 943 installation instructions

Bosch

Bosch 0 986 580 943 installation instructions

EOM T1 Original Metal Series manual

EOM

EOM T1 Original Metal Series manual

KSB Delta Primo F Installation and operating manual

KSB

KSB Delta Primo F Installation and operating manual

PFT PFT G4 operating manual

PFT

PFT PFT G4 operating manual

Samoa Larius 2 Transfer Operating and maintenance manual

Samoa

Samoa Larius 2 Transfer Operating and maintenance manual

Crane BARNES 4SE-L Series Installation and operation manual

Crane

Crane BARNES 4SE-L Series Installation and operation manual

Wilo DrainLift BOX Installation and operating instructions

Wilo

Wilo DrainLift BOX Installation and operating instructions

Hozelock Cyprio EasyClear 9000 Installation and operating instructions

Hozelock Cyprio

Hozelock Cyprio EasyClear 9000 Installation and operating instructions

dosatron D25ALN owner's manual

dosatron

dosatron D25ALN owner's manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.