decorflame QCM375ST-38B User manual

ATTENTION:
1. Find a location for the fireplace heater that is
protected from direct sunlight.
2. Do not plug the unit into the power outlet
before you read all instructions.
ELECTRIC FIREPLACE HEATER
INSTRUCTION MANUAL
QCM375ST-38B

2
WHEN USING ELECTRICAL APPLIANCES, BASIC
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE
THE RISK OF FIRE, ELECTRIC SHOCK, AND INJURY TO
PERSONS, INCLUDI NG THE FOLLOWING:
IMPORTANT SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
1) Read all instructions before using this
electric fireplace heater.
2) This electric fireplace heater is hot when
in use. To avoid burns, do not let bare skin
touch hot surfaces. The grill directly in front of
the heater outlet becomes hot during heater
operation. Keep combustible materials, such
as furniture, pillows, bedding, papers, clothes,
and curtains at least 3 feet (0.9 m) away from
the front of the unit and keep them away from
the sides and rear.
3) Extreme caution is necessary when any
heater is used by or near children or invalids
and whenever the fireplace is left operating
and unattended.
4) Always unplug fireplace when not in use.
5) Do not operate any electric fireplace with
a damaged cord or plug or after the heater
malfunctions, has been dropped or dam-
aged in any manner. Return fireplace heater
to authorized service facility for examination,
electrical or mechanical adjustment, or repair.
6) Do not use outdoors.
7) This electric fireplace heater is not intended
for use in bathrooms, laundry areas and
similar indoor locations. Never locate heater
where it may fall into a bathtub or other water
container.
8) Do not run cord under carpeting. Do not
cover cord with throw rugs, runners, or similar
coverings. Arrange cord away from traffic area
and where it will not be tripped over.
9) To disconnect fireplace, turn controls to off,
then remove plug from outlet.
10) Connect to properly grounded outlets only.
11) Do not insert or allow foreign objects to
enter any ventilation or exhaust opening as
this may cause an electric shock or fire, or
damage the heater.
12) To prevent a possible fire, do not block air
intakes or exhaust in any manner. Do not use
on soft surfaces, like a bed, where openings
may become blocked.
13) A heater has hot and arcing or sparking
parts inside. Do not use it in areas where
gasoline, paint, or flammable liquids are used
or stored.
14) Use this fireplace heater only as described
in this manual. Any other use not recom-
mended by the manufacturer may cause fire,
electric shock, or injury to persons.
15) Avoid the use of an extension cord because
the extension cord may overheat and cause
a risk of fire. However, if you have to use an
extension cord, the cord shall be No.16AWG

3
minimum size and rated not less than 1875
watts.
16) Do not plug this product into a receptacle
controlled by a wall switch or dimmer.
17) When storing or transporting the unit and
cord, keep in a dry place, free from excessive
vibration and store so as to
avoid damage.
CAUTION
If you use this heater in conjunction with a
thermal control, a program controller, a timer
or any other device that switches the heater on
automatically, remember to observe all safety
warnings at all times. The fireplace heater has
safety overheat protection. If the overheat pro-
tection trips, switch off all switch buttons and
wait approximately 5 -10 minutes. It should
reset automatically once the unit cools down.
CAUTION: IMPORTANT
SAFETY INSTRUCTION
(FOR LAMP)
This luminaire has a polarized plug (one blade
is wider than the other) as a feature to reduce
the risk of electric shock. This plug will fit in a
polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician.
Never use with an extension cord unless plug
can be fully inserted. Do not alter the plug.
SAFETY INSTRUCTIONS
INSTRUCTIONS PERTAINING
TO A RISK OF FIRE, ELEC-
TRIC SHOCK, EXPOSURE TO
EXCESSIVE UV RADIATION
OR INJURY TO PERSONS.
LIGHTED LAMP IS HOT!
1. Turn off and unplug the power cord before
attempting any maintenance or cleaning.
Allow at least 10 minutes to cool before
replacing bulbs.
2. Bulb(s) get HOT quickly! Contact only switch/
plug when turning on.
3. Do not touch HOT lens, guard or enclosure.
4. Do not remain in light if skin feels warm.
5. Do not look directly at the lighted bulb(s).
6. Keep lamp away from material that
may burn.
7. Use only JC type Max 10W watt 12V
halogen bulb(s).
8. Do not touch the bulb(s) at any time. Use
a soft cloth. Oil from skin may damage the
bulb(s).
9. Do not operate the lamp with a missing or
damaged lens, lens acts as guard/shield and
UV light filter.
10. This lamp is intended for surface mounted
only and to be used as an under cabinet light.

4
SAFETY INSTRUCTIONS
11. Use only insulated staples or plastic ties to
secure cords.
12. Route and secure cords so that they will
not be pinched or damaged when the cabinet
is pushed to the walL.
13. Position the portable cabinet light with
respect to the cabinet so the lamp replace-
ments markings are able to be read during
relamping.
14. Not intended for recessed installation in
ceilings or soffits.
15. Not intended for surface installation inside
built-in furnishings such as kitchen cabinets,
china cabinets, or trophy cases;
16. The national Electrical Code (NEC) does not
permit cords to be concealed where damage
to insulation may go unnoticed. To prevent fire
danger, do not run cord behind walls, ceilings,
soffits, or cabinets where it may be inacces-
sible for examination. Cords should be visu-
ally examined periodically and immediately
replaced when any damage is noted.
SAVE THESE INSTRUCTIONS
FOR FUTURE USE.
WARNING
Procedures and techniques if not care-
fully followed - will result in damage to the
equipment. - will expose the user to the risk
of serious injury, illness or death.
This electric fireplace heater is for use on
120 volts. The cord has a plug as shown at
A in illustration below. An adapter as shown
at C is available for connecting three-blade
grounding-type plugs to two-slot recep-
tacles. The green grounding plug extending
from the adapter must be connected to
a permanent ground such as a properly
grounded outlet box. The adapter should not
be used if a three-slot grounded receptacle
is available.
A 15 AMP circuit is required to operate this
heater. If the breaker trips when the heater
is used then you may need to move the
heater to another location or unplug other
appliances that are on the same circuit. If
you require an extension cord use one that
is rated at 1875 watts.

5
IMPORTANT
Please note when you open the carton care-
fully check the unit and make sure there are
no damages. If you have any problems with
the unit, with how the various functions work
or with hidden damages or missing parts
please call 1-800-459-4409 (EST) immedi-
ately for service. NOTE: DO NOT RETURN
UNIT TO THE STORE BEFORE CALLING THE
TOLL FREE NUMBER. Do not dispose of your
cartons until you are completely satisfied
with your new fireplace heater. Read all in-
structions thoroughly before operating your
new Electric Fireplace.
NOTE: Light bulbs may become loose during
shipping. If the flame effect is dim or does
not work, please check that light bulb or
bulbs are finger tight in socket. See instruc-
tions for replacing bulb or bulbs. Please do
not return the sample to the store before
checking light bulbs.
NOTE: The electric fireplace heater may emit
a slight harmless odor when first turned
on. This is caused by activating the internal
heater components for the first time and
should not occur again.
SAFETY INSTRUCTIONS