Dedoes Cyclone 0910P User manual
Page 1 PART # M-312 KD RV.8 2019-09-25
** IMPORTANT **
BEFORE USING
THE CYCLONE SHAKER
Pneumatic Paint Shaker
248-624-7710
www.dedoes.com
THANK YOU,
DEDOES INDUSTRIES
Unscrew the lubricator bowl from the shaker
body by hand. Fill the lubricator bowl to the level
mark using air tool oil provided. There may be a
It is crical that the Cyclone Shaker is
properly lubricated during every operaon.
www.dedoes.com
Cyclone Paint Shaker User Manual
Part No: 0910P (Shaker) / 0915P (Pedestal)
Page 2 PART # M-312 KD RV.8 2019-09-25
IMPORTANT
WARRANTY
WARNING
INSTAATION
Shaker
Quick
Connect
Control
Bowl
Inlet
Air Hose
OPTION 2:
Shaker
Bowl
Inlet
OPTION 1:
Quick
Connect
Control
Brass
Close
www.dedoes.com
Cyclone Paint Shaker User Manual
Part No: 0910P (Shaker) / 0915P (Pedestal)
Page 3 PART # M-312 KD RV.8 2019-09-25
PN# Torque Thread Lube Notes
M-29 & M-286 20-25 -lThread ock*
M-299 15 -l MAX** N/A
M-305 -l Thread Se a l
M-2 5 -l Thread ock
15 -l (Ja m) N/A
M-289 28 -l N/A Install the nut away from the housing.
M-23 15 -l Thread ock
M-251 28 -l Oiltorue eenly
M-251 15/18 -lN/A
N/A N/A
M-286 20 -l Thread ock
Cylinder Stud & Jam Nut
Cylinder Stud
Relief Jam Nut
Item
Jaw Bolt Nuts
U-Bolt Nuts
Crank Arm
· Bolt the shaker down securely.
All arts must e comletely clean and luricated efore assemly or raid wear may result.
*NOT: Thread Seal: Non-hardening gasket cement (Permate“Aiaon orm-A-Gasket” or eual).
Thread ock: uricanganaeroic hardening thread locking comound (octe 21“Stud-N-Bearing Mount”or eual).
**(One l. In. euals 1/12 of one l. t.).
www.dedoes.com
Cyclone Paint Shaker User Manual
Part No: 0910P (Shaker) / 0915P (Pedestal)
Page PART # M-312 KD RV.8 2019-09-25
30°
RATION
crushing the can. cans and aerosol cans with lid handle. Tighten
gallons securely with the can lid straight the long sides of the can against the and the corners on the cradles.
gallon or aerosol cans to ensure they do not leak or become loose. Aerosol cans only require
and closing the control turn. If the shaker at the center or is not
enough it may not start Close the control cock the can to one sidere-start.
the shaker the may take a few seconds to start
or screw. If it is not the oil and see
a week
- Unscrew the and any watery/milky oil out.
the oil to the mark
- gasket ring is in and the is screwed on straight.
the shake angle if the air at the shaker is 120 PSI kPa) with an air line at normal follows:
A) a full one-gallon round can of
B) Start the shaker
C) the inch lock nut at the screw on the air inlet the screw to a total shaking angle 30°
D) the shaker and nut while holding
screw and grease for Zerk once
areas.
Grease the crank Zerk (one shot) through hole when can is to Use more air tool oil to internal rust if
air line and install a is oiling each you
calcium or
www.dedoes.com
Cyclone Paint Shaker User Manual
Part No: 0910P (Shaker) / 0915P (Pedestal)
Page 5 PART # M-312 KD RV.8 2019-09-25
Air 90 to 120 PSI gage) (600 to 150 PSI a regulator and relief
of air hose.
Air Inlet ¼ inch (Seal with thread
Shake If at 120 PSI a full gallon can
air normal line (See
Air (0.002 M3/sec) free air with 1 gallon (U.S.) 12 can at 30° shake angle.
ycles/minute at 30° shake at control
for can .
The shaker can hold half cans through four liter round cans.
most aerosols (with gallons.
16 gross can weight.
Recommended Shake
Final inlet
Oil
add three d
manual oiling.
Recommended Petroleum 5W to 10W Non-detergent Rust Air Tool Oil such as 10R. Oil
should not contain gum Do not use motor oil.
Greas calcium or 3 to 6 or more
in se
Cyclone Air Shaker - Dedoes PN# 0910P
Pedestal - Dedoes PN# 0915P
www.dedoes.com
Cyclone Paint Shaker User Manual
Part No: 0910P (Shaker) / 0915P (Pedestal)
Page 6 PART # M-312 KD RV.8 2019-09-25
TROUBOOTING
.
www.dedoes.com
Cyclone Paint Shaker User Manual
Part No: 0910P (Shaker) / 0915P (Pedestal)
Page PART # M-312 KD RV.8 2019-09-25
TROUBOOTING
angle.
www.dedoes.com
Cyclone Paint Shaker User Manual
Part No: 0910P (Shaker) / 0915P (Pedestal)
Page 8 PART # M-312 KD RV.8 2019-09-25
Date
Oil Grease
Okay OkayAdded Added
www.dedoes.com
Cyclone Paint Shaker User Manual
Part No: 0910P (Shaker) / 0915P (Pedestal)
Page 9 PART # M-312 KD RV.8-2019-09-25
Part no. Part no. Descrip
M- Crank Arm Bolt
M- Bolt Bushing
M- Crank Arm Nut
M- Cylinder Stud
M- Cylinder Body
M- U Bolt Kit M- Piston Screw
M-280 Piston
M-281 Rod Bearing
M-282 Rod Seal
M-283 Cylinder Head
M-285 Cylinder Rod
M-286 Rod nd
M- Rod nd Bearing
M-289 Crank Arm
M-290 Crank Pin
M-291 Crank Thrust Washer
M-292 Crank Pin Retaining Ring
M-293 Transfer O-Ring
M- Inlet Vale Body
M-296 Check Vale Disc
M- Vale Disc
M-298 Vale Body O-Ring
M-299 Relief Jam Nut
M-300 Relief Set Screw
M-301 Reliefring
M-302 Relief Ball
M- Brass Close Nie M-255 Jaw Bolt M-303 Outer Vale Body
M- Inleting M- Control Vale M-305 Inletilter
M- Jaw M-260 Austale Seal M-306 ilterring
M- Roll Pin M-261 Austale Jam Nut M- Inletlow
M- Handle M-262 Austale Screw M-308 Vale Body Screw
M- Clamrame Weld M-263 Shock Mount Bushing (ieces) M-309 Transfer Plug
M- Thrust Washer M- Wear Ring M-310 Hose Clam
M- Screw Retaining Ring M-265 Piston O-Ring M-311 Air Hose
M-250 ClamNut - Hand M-266 Head O-Ring M-312 User Manual
M-251 3/8-16 Nut M- Head Retaining Ring M-313 Housing Bolt
M-252 U-Bolt M-268 Main Thrust Washer M- Drain ing
M-252K U-Bolt Kit M- Main ShaM-318 Automac ucator
M-253 ClamScrew M- Main Bearing 0910P Comlete Cyclone Shaker
M- ClamNut - Right Hand M- Zerking 0915P Comlete Pedestal
M-288
M- Inlet alve Body Assembly
Includes: (1) M- (1) M-298(1) M- (1) M-296
Outer alve Body Assembly
M- Includes: (1) M- (1) M-06(1) M-305(1) M-309(1) M-303. (1) M-302(1) M-301(1) M-
300(1) M-299
Cylinder Internal Assembly
Includes: (1) M- (1) M- (1) M-280(1) M- (1) M-265(1) M-
(1) M-285(1) M-286(1) M-
M-
Can Clamp Assembly
Includes: (2) M- (6) M-251(1) M-252() M-255(1) M-253(1) M- (1) M-250(1) M-
(1) M- (1) M- (1) M-
M-
M-
Motor with Crank Arm
Cylinder Motor Assembly
Includes: (1) M-288(1) M- (2) M-293(1) M- (3) M-308
Includes: (1) M-295(1) M- (1) M-316(1) M- (2) M- (1) M- (1) M-289(1) M-
(2) M-292(2) M-291(1) M-290
Descrip
M-284
Front Cylinder Head Assembly
Includes: (1) M-281(1) M-282(1) M-283(1) M-266
Shaker Repair Kit
Inlet Fing Assembly
Includes: (1) M-262(1) M-261(1) M-260(1) M-
M-
Includes: (1) M-296(1) M- (1) M-298(1) M-305(2) M-310(1) M-311
(1) M-263(1) M- (1) M-265(1) M-266(2) M-293
M-RK
Housing Assembly
Includes: (2) M- (1) M- (1) M-
M-
Includes: (1) M-252(2) M-251
www.dedoes.com
Cyclone Paint Shaker User Manual
Part No: 0910P (Shaker) / 0915P (Pedestal)
Page 10 PART # M-312 KD RV.8 2019-09-25
M-274
Crank Arm
Bolt
M-264*
Wear Ring
Piston O Ring
M-266*
Head O Ring
M-267
Head Retaining Ring
M-277
Cylinder
Stud
Transfer O Ring
M-278
Cylinder
Body
M-279
Piston Screw
M-280
Piston
M-281
Rod Bearing
M-282
Rod Seal
Cylinder
Head
Cylinder Rod
M-286
Rod End
M-287
Rod End Bearing
Bolt Bushing
M-272
M-292
Crank Pin
Retaining Ring
M-290
Crank Pin
M-291
Crank Thrust
Washer
M-289
Crank Arm
M-276
Crank Arm Nut
M-284
Front Cylinder
Head Assembly
M-294
Body
M-298*
O-Ring
M-299
Relief Set Screw
Relief Spring
Relief Ball
M-297*
M-296*
Check
Transfer Plug
Nuts
Shock Bushing
Lubricator
M-240
Brass Close
Nipple
M-260
M-261
M-262
M-242
Assembly
M-270
M-268
Main Thrust
Washer
M-271
Main Bearing
M-272
Housing Assembly
M-291
Crank Thrust
Washer
M-292
Crank Pin
Retaining Ring
Air Hose
Inlet
Elbow
Inlet Filter
Filter
Spring
Hose Clamp
Hose Clamp
Body
Bolt Bushing
M-249
Screw Retaining
Ring
M-248
Thrust Washer
M-246
Handle
Roll Pin
M-244
Nut
U Bolt
M-247
Clamp Frame
Clamp Screw
Clamp Nut
Nut
Nut
Clamp Nut
Right Hand
Can Clamp
Assembly
Motor with
Crank Arm
Assembly
Cylinder
Motor
Assembly
Body Assembly
M-288
Cylinder Internal
Assembly
Outer
Assembly
U Bolt Kit
Page 11 PART # M-312 KD RV.8-2019-09-25
PEDESTAL TO FLOOR TEMPLATE
The Pedestal includes six interior holes to mount
damage will result. Use the outer holes in
Page 12
PART # M-312 KD RV.8-2019-09-25
SHAKER TO BENCH TEMPLATE
8.0 INCH
inch (11 mm) holes in the surface and install the shaker
using
This manual suits for next models
1
Table of contents
