DEI 758SCNE Quick start guide

1. CAUTION:
( Non-Condensing )
2.3 Storage temperature -10 60 , 90%RH ( Non-Condensing )
2.4 Power supply Power supplied by power board DC 12V
(If communication wire is over 100 meters, an extra power DC12V is required)
2.5 Temperature display range 0 50 in 0.5 steps.
2.6 Communication wire 2 wires(pdes) + isolated wire (connect GND), UL2464 / 24AWG
with isolated wires.
2.7 Communication protocol Modbus-RTU (RS485)
2.8 Max communication distance1200M
2.9 Max control qty. Can control 63 sets of Pns DEI-
2.10 Alarm contact buzzer
2.11 District control Divide FCUs into 4 districts control (group control/ schedule).
DEI-201N AHU/ VAV can't be divided into district control.
3. FUNCTION DESCRIPTION :
3.1 Buttons description
3.1.1 POWER To switch on / off the power, set district control/ schedule of power status.
3.1.2 Set temp./ max limit for heating/ min limit for cooling/ room temp.
calibration (0.5 ) or into max limit for heating setting.
3.1.3 Set temp./ max limit for heating/ min limit for cooling/ room temp.
1.1 Please install according to the wiring diagram to avoid incorrect wiring, any improper
wiring or installation is beyond our warranty.
1.2 Please do not install it in humid environment to ensure good signal communication.
1.3 Please use the communication wire UL2464/24AWG or 26AWG 3C communication
isolated wire.
2. SPECIFICATION:
2.1 Appearance
2.2 Operation temperature 0 50 , 90%RH
758PN/758FPN/100A/100D/201NAHU/
201NVAV
calibration (-0.5 ) or into min limit for cooling setting.
3.1.4 IP & IP To select the fan IP, or into group control status.
3.1.5 Mode To setup the mode of fan coil unit (in single or group), or daily schedule setting.
3.1.6 Fan To setup the fan speed (in single or group), or into room temp. calibration setting.
3.1.7 Light To switch on/ off the LCD backlight or into parameter setting.
3.1.8 Lock To lock or unlock the panel.
3.2 Function
3.2.1 IP address of PN It displays the monitored and controlled PNs' address from 01~63;
displays AL or A1~ A4 for the district control; displays AC for controlling all of PNs.
When icon is not illuminated, it means there is abnormal communication between SCN
and PN.
3.2.2 Power Control the selected PN or all PNs or district PNs (schedule), power on / off
status.
3.2.3 Temperature setting
3.2.3.1 When setting temperature, the panel shows the setpoint (it back to room
temperature if the up / down buttons have not been pressed within 5 seconds).
In normal situation, the display shows the room temperature of the monitored
PN (icon of room temperature shows on)
3.2.3.2 Temperature setting range
heating: 0 ~max limit of heating, cooling: min
limit of cooling ~35 (0.5 in step)
3.2.3.3 Whenever temperature setting is adjusted (by LCN or PC), the display shows
the new setpoint for 5 seconds.
3.2.4 Mode control
3.2.4.1 To setup the mode status of the single PN or group PNs (Auto, cooling, fan, he
ating and humidity).
3.2.4.2 When changing to auto air conditioning, cooling or heating mode, fan speed
will be changed to Auto.
3.2.4.3 When changing to fan or dehumidifying mode, fan speed will be changed to
Low.
3.2.5 Fan speed control To setup 4 fan speeds for the single or district (all districts) PNs
( Auto, High, Medium and Low). No auto speed under the fan and
dehumidifying mode.
3.2.6 Lock function
3.2.6.1 Press Lock button, the display will show the lock icon and the sub controller
will be locked. To unlock the panel, press Lock button again.
3.2.6.2 Press Lock button within 3 seconds, the display shows LC. Under this mode,
the main controller is locked; besides Power, IP selection, Light and Lock,
other buttons are not available to operate. Press lock again within 3 seconds,
to unlock the panel. Under group control, only setting power status.
3.2.6.3 Once setup lock from PC, the display shows LP. Under this mode, the main
controller is locked; besides Power, IP selection, Light and Lock, other buttons
are not available to operate, only can be unlocked by PC operation. In Group
control, only the power button is available.
3.2.7 Max limit heating setting (DEI-758FPN / 201NAHU / 201NVAV)
When DEI-758FPN/201NAHU / 201NVAV in OFF status, press for 3 seconds into
max limit heating setting (show HS) and adjust by .
Setting range 0 ~ 35 . Under setting status, press IP to into AL-HS setting.
After completing setting, press Light to save or press Fan to cancel.
-758SCNE Operational Manual-758SCNE Operational Manual Version 02
5INSLL20503
Button description
Fan IP +1
Fan IP -1
Backlight/
confirm
To increase
temp.
To decrease
temp.
Lock /Week
Mode / Select
Fan / Cancel
3
4
2
1
5
Light
Mode
Fan
Lock
POWER
IP
IP
Power
Room Temp.
/Set Temp
IP address for
SCN / Time
Su Tu Th Fr Sa
3
4
2
1
5
ON
OFF
IP address
of PN
Room Temp.
Symbol
Week
Weekday
operation
Mode
Unit
Lock
Fan speed
Link status
LCD display
Separated line
Swing

3.4.8 Sch.SP01 schedule point select, press IP to select district and schedule points:
01~08,11~16,21~26,31~36,41~46, press Light to into setting.
3.4.8.1 Lock weekday select (can't change when parameter blinking).
3.4.8.2 IP Schedule hour setting (0~23).
3.4.8.3 IP Schedule minute setting (0~59).
3.4.8.4 Mode Schedule points and operation setting (schedule time is no display
when no schedule).
3.4.8.5 Schedule setting (0~35.0)
3.4.8.6 POWER Sechedule power (On/Off)
3.4.8.7 Light Confirm setting.
3.4.8.8 Fan Cancel setting / return to 3.4.8 schedule point selection.
5
5
5 Max limit heating setting(HS)/ Min limit cooling setting
(CS)/ Temp. calibration(OT).
5
5
3.6 Link display
3.6.1 Product model and connection check in 20 seconds after power on.
3.6.2 If the IP has connected successfully, IP address is able to select, even if any
connection failure.
3.6.3 To remove the display of IP connection interruption, press POWER button to remove
link status.
4. Failure Elimination :
4.1 E1 Sensor failure.
4.2 EE Memory failure.
4.3 EC Abnormal communication of power board (no any linking situation of power board).
4.4 FA Exceeding temperature alarm.
4.5 PN location is still able to be selected, even if there is any alarm occurred (except EC).
No any button pressed in 5 seconds, it comes to display the status of alarmed PN.
4.6 If there are multi-PN in alarm simultaneously, display shows each alarmed PN in turns for
5 seconds.
4.7 LCD backlight is illuminated constantly when under failure alarm.
4.8 When in failure alarm, buzzer ON for 0.8 seconds and OFF for another 0.8 seconds.
3. All group control mode (AC=ON)
3. .1 Under this mode, can't into district mode.
3. .2 Under this mode, can't set the
3. .3 Under this mode, fan address show AC. When change fan, show fan IP 2 seconds.
3. .4 Under this mode, operated model/ fan speed/ setpoint/ lock/ power are the controlled
command for all fan.
3.2.8 Min limit cooling setting (DEI-758FPN / 201NAHU / 201NVAV)
When DEI-758FPN/ 201NAHU / 201NVAV in OFF status, press for 3 seconds
to into min limit cooling setting (show CS) and adjust by .
Setting range 0 35 ; Under setting status, press IP into AL-CS setting.
After complete setting, press Light to confirm or press Fan to cancel.
3.2.9 Temperature calibration setting (DEI-758FPN/201NAHU/201NVAV)
OFF status in single fan, press Fan for 3 seconds into temperature calibration
(Ot) mode, and press to adjust value, setting range -8 8 . Press Light to
confirm or press Fan to cancel after setting.
3.2.10 Auto air conditioning while power off: under this mode, the display shows the room
temperature and it blinks.
3.3 Group control function press IP for 3 seconds to into or exist group status (fan address
shows all district (AL) or district A1~A4.
3.3.1 Press IP to select district, can select AL for all districts, or A1~A4 district (only fans
in district accept command).
3.3.2 Under group control, press Power to set all districts (district) power status.
3.3.2.1 Show Pr On, is meaning set all districts (district) start operating.
3.3.2.2 Show Pr OF, is meaning set all districts (district) stop operating.
3.3.2.3 The condition of group controller switch on power
Group commend switch off controller power in advance.
3.3.3 Under the group control, press Mode to set all districts (district) group mode status.
3.3.4 Under the group control, press Fan to set all districts (district) group fan speed status.
3.3.5 Under the group control, press Lock to set all districts (district) group lock status.
3.3.6 Under the group control, press to set all districts (district) group set temp.
3.3.7 Under the group control, the separated line is blinking is meaning Group Control
setting is waiting confirm; press Light to confirm or IP to cancel setting.
3.3.8 Under the AL-HS, press to set all districts Max limit heating setting.
3.3.9 Under the AL-CS, press to set all districts Min limit cooling setting.
3.4 Main control parameter setting: under normal mode, press Light for 3 seconds to into /
exist main control parameter setting; in the parameter,
press Mode to select below parameter.
3.4.1 IP (IP setting) press IP to select main controller IP=01~99, press Light to
confirm, press Fan to cancel.
3.4.2 br (Baud rate setting) press IP to select baud rate 4800~1152, press Light to
confirm, press Fan to cancel.
3.4.3 Pr (Parity bite setting) press IP to select n81/O81, press Light to confirm setting,
press Fan to cancel.
3.4.4 AC (All group control) press IP to select AC ON/OF, press Light to confirm
setting, press Fan to cancel.
3.4.5 rtc (Alarm clock setting) setting DEI-758SCN time (retain timing in 72 hours after
power off)
3.4.5.1 Lock set weekday (Sun~Sat).
3.4.5.2 IP set hour (0~23).
3.4.5.3 IP set min (0~59).
3.4.5 4 Light confirm setting Fan cancel setting.
3.4.6 Ar district setting, press IP to select IP1~63, press IP to set district (0A~4A),
press Light to confirm, press Fan to cancel.
3.4.7 Sch.dE weekday schedule, press IP to select weekday operation schedule,
press Light to confirm setting, press Fan to cancel.