DelRay MONTIGO DRL3613NI Instruction Manual

XG0226 - 042220
Installation & Maintenance Manual
®
C
US
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious injury,
death, or property damage.
—Donotstoreorusegasolineorotherammablevaporsand
liquidsinthevicinityofthisoranyotherappliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phoneinyourbuilding.
• Leavethebuildingimmediately.
• Immediatelycallyourgassupplierfromaneighbour's
phone. Follow the gas supplier’s instructions.
• Ifyoucannotreachyourgassupplier,callthere
department.
—Installationandservicemustbeperformedbyaqualied
installer,serviceagencyorthegastter.
DelRay INDOOR DIRECT VENT GAS FIREPLACE
DRL3613NI 16,000 BTU/hr Natural Gas or Propane Gas
DRL3613NI-2 16,000 BTU/hr Natural Gas or Propane Gas
DRL4813NI 21,000 BTU NG /19,000 BTU Propane /hr
DRL4813NI-2 21,000 BTU NG /19,000 BTU Propane /hr
DRL6013NI 28,000 BTU NG /25,000 BTU Propane /hr
DRL6013NI-2 28,000 BTU NG /25,000 BTU Propane /hr
A barrier designed to reduce the risk of burns
from the hot viewing glass is provided with this
appliance and must be installed for the protection
of children and other at-risk individuals.
HOT GLASS WILL CAUSE BURNS.
DO NOT TOUCH GLASS UNTIL
COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
DANGER
Installation and service must be performed by a qualied installer,
service agency or the gas tter. Check local codes and read all
instructions prior to installation.
Some materials used in the manufacturing process of this product can
expose you to Benzene which is known in the State of California to
cause cancer and birth defects or other reproductive harm. For more
information go to www.P65warnings.ca.gov
WARNING
Installer: Leave this manual with the appliance. Please refer to the
Montigo website for the most current version of the replace manual
Consumer: Retain this manual for future reference. Please refer to the
Montigo website for the most current version of the replace manual
NOTICE

2
General
XG0226 - 042220
Figure 1 DRL Specications
Congratulations on your purchase of a Montigo Fireplace.
With over 30 years of experience, Montigo is committed to providing
you with a gas fireplace that is not only a beautiful addition to your
space, but that is also designed and manufactured to the highest
safety, reliability and engineering standards.
We strongly encourage you to read and carefully follow the
instructions laid out in this Installation, Operation and Maintenance
Manual and retain it for your future reference. Pay special attention
to all cautions, warnings, and notices throughout this manual
intended to ensure your safety.
This manual covers installation, operation and maintenance. Lighting,
operation and care of this replace can be easily performed by the
homeowner. All installation and service work should be performed
by a qualied or licensed installer, plumber or gas tter as certied
by the state, province, region or governing body where the replace
is being installed.
This installation, operation and maintenance manual is applicable
to the models described in Table 1. Refer to your rating plate to
verify included options.
Warranty and Installation Information: (See Appendix B)
The Montigo warranty will be voided by, and Montigo disclaims any
responsibility for, the following actions:
• Modication of the replace and/or components including Direct-
Vent assembly or glass doors.
• Use of any component part not manufactured or approved by
Montigo in combination with this Montigo replace system.
• Installation other than as instructed in this manual.
• Consult your local Gas Inspection Branch on installation
requirements for factory-built gas replaces. Installation & repairs
should be done by a qualied contractor.
BTU Listing
MODEL Natural Gas Liquid Propane BTU / hr Linear Burner w/ Glass Accessories SIT Elect. Ignition SIT Elect. Ignition BASIC P.4. 1-15 Eciency‡
DRL3613NI X 16,000 X X 71
DRL3613LI X 16,000 X X 71
DRL3613NI-2 X 16,000 X X 71
DRL3613LI-2 X 16,000 X X 71
DRL4813NI X 21,000 X X 63
DRL4813LI X 19,000 X X 60
DRL4813NI-2 X 21,000 X X 63
DRL4813LI-2 X 19,000 X X 60
DRL6013NI X 28,000 X X
DRL6013LI X 25,000 X X
DRL6013NI-2 X 28,000 X X
DRL6013LI-2 X 25,000 X X
Introduction
Safety Alert Key
Young children should be carefully supervised when they are in the
same room as the appliance. Toddlers, young children, and others
may be susceptible to accidental contact burns. A physical barrier is
recommended if there are at-risk individuals in the house. To restrict
access to a replace or stove, install an adjustable safety gate to keep
toddlers, young children, and other at-risk individuals out of the room
and away from hot surfaces
CAUTION
Indicates a hazardous situation which, if
not avoided, WILL result in death or serious
injury or property damage.
Indicates a hazardous situation which, if not
avoided, WILL result in minor or moderate
injury.
Indicates a hazardous situation which, if not
avoided, COULD result in death or serious
injury or property damage.
Indicates practices that are important, but
not related to personal injury.
DANGER
CAUTION
WARNING
NOTICE

3
General
XG0226 - 042220
Contents
Safety Alert Key.................................................................................. 2
Introduction ....................................................................................... 2
Efficiency............................................................................................. 2
Section A: Before You Begin .......................................................................4
Installation Checklist ......................................................................................4
Standard Installation Checklist....................................................................5
Rating Plate Sample .......................................................................................6
Section 1: Dimensions ....................................................................... 7
DelRay Dimensions ........................................................................................7
Section 2: Framing ............................................................................ 8
In Wall and Corner Dimensions..................................................................8
Clearances........................................................................................................9
Recommended flooring considerations ...................................................9
Standard installation....................................................................................10
TV over fireplace installation......................................................................10
Vented installation .......................................................................................11
Section 3: Venting ............................................................................ 12
Section 3-3-1: Venting Layout ......................................................... 13
Wall and Roof mounted venting ...............................................................13
Co-linear venting into existing masonry chimney ................................14
Framing with Cool Wall Advantage...........................................................15
Sidewall louvers (horizontal and vert.) ..................................................15
Sidewall plenum (horizontal and vert.) .................................................15
Section 3-2: Installing a Roof Mounted Direct Vent Termination
for4''/7''(MVTK-1)............................................................................ 16
Section 3-2-1: Venting Layout ...................................................................16
Section3-3:InstallingaWallMountedTermination4''/7'' .........17
Section 3-3-2: Venting Components........................................................18
Section 3-3-2.2: 4” x 7” Venting Components........................................19
Flexmaster as alternate venting................................................................20
Section3-3-3:HeatShields4''/7''.................................................... 21
Section 4: Wiring .............................................................................. 22
DRL**13 (N/L) I Wiring Diagram ...............................................................22
Installation of the wall switch.....................................................................22
DRL**13 (N/L) I-2 Wiring Diagram ...........................................................23
Installation of Electrical Supply .................................................................23
Section 5: Installing the gas line.....................................................24
Fuel Type.........................................................................................................24
Gas Pressure .................................................................................................24
Section 5-3: GAS CONNECTION................................................................24
Finishing Safety Zone...................................................................................24
Section 6: Finishing .......................................................................... 25
Finishing Around the Fireplace .................................................................25
Finishing when using cool wall kit or vented chase .............................25
Chase venting (optional) .............................................................................26
Sidewall clearances......................................................................................27
Cement Board Install...................................................................................27
Section8:Removing&InstallingtheScreen/Door .................... 28
Removing the Screen...................................................................................28
Reinstalling the Screen................................................................................28
Removing the door ......................................................................................28
Reinstalling the door....................................................................................28
PropaneConversion ........................................................................ 29
Section 9: Installing the Accessories.............................................. 31
Installing the Fireglass or Optional Glass Media...................................31
DelRay 36" Optional Log Kit Installation .................................................31
Propane Driftwood Layout.........................................................................31
Natural Gas Driftwood Layout...................................................................31
DelRay 48" Optional Log Kit Installation .................................................32
Propane Driftwood Layout.........................................................................32
Natural Gas Driftwood Layout...................................................................32
Section 10: Cleaning and Maintenance ........................................ 34
General............................................................................................................34
Cleaning ..........................................................................................................34
Pilot Burner Adjustment. ............................................................................34
POD - Pilot on Demand.................................................................... 35
What is POD mode?.....................................................................................35
Remote Continuous Pilot (CPI) Selection ...............................................35
Installing the POD Jumper Cable ..............................................................35
Troubleshooting............................................................................................36
Indoor fireplace in protected outdoor applications ................... 37
See through fireplace..................................................................................37
Notes ...............................................................................................................37
Single sided fireplace...................................................................................37
Appendix A: Venting Terminations................................................ 38
Appendix B: Warranty ..................................................................... 39
Appendix B: Warranty Continued .................................................. 40
Appendix C: Amendment ................................................................ 41
(GasFireplace/EquipmentsoldintheStateofMassachusetts)41
DRL3613*I BASIC Exploded Parts.................................................... 42
DRL3613*I-2 FULL LOAD Exploded Parts ....................................... 43
DRL4813*I BASIC Exploded Parts.................................................... 44
DRL4813*I-2 FULL LOAD Exploded Parts ....................................... 45
Thisappliancemaybeinstalledinanaftermarket,
permanently located, manufactured home (USA
only)ormobilehome,wherenotprohibitedby
local codes.
This appliance is only for use with the type of gas
indicatedontheratingplate.Aconversionkitis
availableforthisappliance.

4
General
XG0226 - 042220
IMPORTANT MESSAGE: SAVE THESE INSTRUCTIONS
The DelRay replaces must be installed in accordance with these
instructions. Carefully read all the instructions in this manual rst.
Consult the Local Gas Branch to determine the need for a permit prior
to starting the installation. It is the responsibility of the installer to
ensure this replace is installed in compliance with the manufacturers
instructions and all applicable codes.
InstallationChecklist
• Determine the desired install location of your replace.
• See Section 1, Dimensions on Page 6, and refer to the Framing
Section 2 for details.
• Select the location of your termination and resulting vent run.
• Should it be impossible to meet the venting requirements laid out
in Section 3: Venting, please contact your Montigo dealer regarding
the use of a Montigo Power Vent.
• Lay out the Vent run; calculating the required elbows and straight
runs of 4"/7" ex and/or rigid pipe.
• Layout Electrical Requirements refer to Section 4: Wiring, for Details.
• Refer to Section 5: Installing the Gas Line, for details on the gas
connection and access.
• Refer to local codes and guidelines for installation requirements.
• Installation and repairs should be done by a qualied contractor
and must conform to:
• Installations in Canada must conform to the local codes or in the
absence of local codes to the current version of Natural Gas and
Propane Installation Code, CSA B149. Electrical installations must
conform to the local codes or, in the absence of local codes, to the
current version of Canadian Electrical Code, CSA C22.1.1
• Installations in the USA must conform to the local codes or in the
absence of local codes to the current version of National Fuel Gas
Code, ANSI Z223.1/NFPA 54. Electrical installations must conform
to the local codes or, in the absence of local codes, to the current
version of the National Electrical Code, ANSI/NFPA 70. See Appendix
C for installation within the State of Massachusetts
Do not use this appliance if any part has been under water.
Immediately call a qualied service technician to inspect the appliance
and to replace any part of the control system and any gas control that
has been under water
Due to high temperatures, the appliance should be located out of
trac and away from furniture and draperies
Children and adults should be alerted to the hazards of high surface
temperature and should stay away to avoid burns or clothing ignition
A barrier designed to reduce the risk of burns from the hot viewing
glass is provided with this appliance and shall be installed for the
protection of children and other at-risk individuals
Clothing or other ammable material should not be placed on or near
the appliance
Installation and repair should be done by a qualied service person.
The appliance should be inspected before use and at least annually
by a professional service person. More frequent cleaning might be
required due to excessive lint from carpeting, bedding material, etc. It
is imperative that control compartments, burners, and circulating air
passageways of the appliance be kept clean
NOTICE
NOTICE
NOTICE
NOTICE NOTICE
NOTICE
ThisappliancemaybeinstalledasanOEMinstallationina
manufacturedhome(USAonly)ormobilehomeandmustbe
installed in accordance with the manufacturers instructions and
the Manufactured Home Construction and Safety Standard, Title 24
CFR, Part 3280, in the United States, or the Standard for Installation in
Mobile Homes, CAN/CSA Z240 MH, in Canada.
This appliance is only for use with the type(s) of gas indicated on
theratingplate.Aconversionkitisavailableforthisappliance.
Section A: Before You Begin

5
General
XG0226 - 042220
StandardInstallationChecklist
This standard installation checklist is to be used by the installer in conjunction with, not instead of, the instructions contained within this
installation manual.
Customer Date Installed:
Install Address: Location of Fireplace:
Installer:
Model (circle one): DRL3613NI, DRL3613NI-2, DRL4813NI, DRL4813NI-2
DRL3613LI, DRL3613LI-2, DRL4813LI, DRL4813LI-2, DRL6013LI,
DRL6013LI-2, DRL6013LI, DRL6013LI-2
Dealer Phone:
Serial #:
*Only applicable for Builders Series
YES NO IF NO, WHY NOT?
Appliance Install: Section 2
Framing complies with install manual.
Standos have been installed.
Proper clearances have been maintained.
Venting: Section 3
Venting conguration complies with vent diagrams.
Venting installed, fastened, and secured in place maintaining proper clearance.
Firestops installed.
Exterior wall/roof ashing installed and sealed in compliance with local building code.
Terminations installed and sealed in compliance with local building code.
Direct vent termination is highest point in vent assembly.
Wiring/Electrical:Section4
Unswitched power provided to the appliance PPO box.
Low voltage wire connected to dry contact wall switch (non-powered)*
Gas: Section 5
Proper appliance for fuel type.
Was a conversion performed?
Leak check performed & inlet pressure veried.
Finishing: Section 6
Only non-combustible materials installed in non-combustible areas.
Clearances meet installation manual requirements
Mantels and/or projections comply with install manual
Appliance Setup: Section 7 through 9
Media, door, and screen installed according to install manual
Manual given to home owner.
Started appliance and veried no gas leaks exist.
Comments:

6
General
XG0226 - 042220
Rating Plate Sample
Figure 1.1 Rating Plate for DelRay DRL3613NI Figure 1.2 Rating Plate for DelRay DRL4813NI
Serial No.:
N & H ( 0 - 4500 ft. / 0 - 1371 m.)
Max. Input Min. Input Output / Orifice Size / Taille D'Orifice Gas Manifold
Max. Entrée Min. Entrée
Rendement
Front/Avant Rear/Derrière Pressure / Pression
BTU/H BTU/H BTU/H
D'Admission Du Gaz
X16,000 16,000 N/A 49 DMS / N/A 3.5" W.C.
LBA ANSI Z21.88-2016 RV. 06-19-2019
Type: Vented Gas Fireplace Heater For Indoor Use Only *Clearance to Combustibles
Not for use with solid fuel. / Pas pour l'usage avec le combustible solide. *Degagements Aux Combustibles
Not for use with air filters. / Pas pour l'usage avec des filtres à air. Sides/Côtés: 1"
Model No. Modèle. DRL36NI Back/Derrière: 2" Distributed by / distribué par: Canadian Heating Products Inc., Langley BC, (www.montigo.com)
Floor/Plancher: 0"
Montigo DelRay Corp., Ferndale, WA. (www.montigo.com)
X-XXXXXX-XXXXXX Top-Top Vent/Du Haut-Évent Du Haut: 21"
Top-Rear Vent/Du Haut-Évent Arrière: N/A Mantel/Manteau: 6"
Tested To / Examiné À:
Recess Depth/ Profondeur D'Encadrement:
14.25"
Electrical Rating / Estimation Électrique:115V / 1Ph / 60Hz /less than 12A
Flue: 1"
Altitude Rating / Estimation D'Altitude:
CSA/ANSI Z21.88-2019 / CSA2.33-2019
Fuel Type / Type De Carburant:
Min. Gas Supply
Pressure/ Min. Pression
Do Not Remove
This Label
D'Alimentation Du Gaz
Natural Gas / Gaz Naturel 5.5" W.C.
Made in China
Fabriqué en Chine
16,000 16,000 N/A 1.15 mm / N/A 10" W.C. 13" W.C.
N'enlevez Pas Cette
Étiquette
Propane / Gaz Propane
FOR USE WITH GLASS DOORS AND SCREENS CERTIFIED WITH THE APPLIANCE ONLY Pour utilisation avec portes de verre and écrans de certifiés avec l'appareil seulement
*Refer to installation manual for more information. *Référez-vous au manuel d'installation pour plus d'information.
Serial No.:
N & H ( 0 - 4500 ft. / 0 - 1371 m.)
Max. Input Min. Input Output / Orifice Size / Taille D'Orifice Gas Manifold
Max. Entrée Min. Entrée
Rendement
Front/Avant Rear/Derrière Pressure / Pression
BTU/H BTU/H BTU/H
D'Admission Du Gaz
X21,000 21,000 N/A 2.15 mm / N/A 3.5" W.C.
LBA ANSI Z21.88-2016 RV. 06-19-2019
Type: Vented Gas Fireplace Heater For Indoor Use Only *Clearance to Combustibles
Not for use with solid fuel. / Pas pour l'usage avec le combustible solide. *Degagements Aux Combustibles
Not for use with air filters. / Pas pour l'usage avec des filtres à air. Sides/Côtés: 1"
Model No. Modèle. DRL48NI Back/Derrière: 2" Distributed by / distribué par: Canadian Heating Products Inc., Langley BC, (www.montigo.com)
Floor/Plancher: 0"
Montigo DelRay Corp., Ferndale, WA. (www.montigo.com)
X-XXXXXX-XXXXXX Top-Top Vent/Du Haut-Évent Du Haut: 21"
Top-Rear Vent/Du Haut-Évent Arrière: N/A Mantel/Manteau: 6"
Tested To / Examiné À:
Recess Depth/ Profondeur D'Encadrement:
14.25"
Electrical Rating / Estimation Électrique:115V / 1Ph / 60Hz /less than 12A
Flue: 1"
Altitude Rating / Estimation D'Altitude:
CSA/ANSI Z21.88-2019 / CSA2.33-2019
Fuel Type / Type De Carburant:
Min. Gas Supply
Pressure/ Min. Pression
Do Not Remove
This Label
D'Alimentation Du Gaz
Natural Gas / Gaz Naturel 5.5" W.C.
Made in China
Fabriqué en Chine
19,000 19,000 N/A 1.3 mm / N/A 10" W.C. 13" W.C.
N'enlevez Pas Cette
Étiquette
Propane / Gaz Propane
FOR USE WITH GLASS DOORS AND SCREENS CERTIFIED WITH THE APPLIANCE ONLY Pour utilisation avec portes de verre and écrans de certifiés avec l'appareil seulement
*Refer to installation manual for more information. *Référez-vous au manuel d'installation pour plus d'information.

7
Installation
XG0226 - 042220
DelRay Dimensions
Section 1: Dimensions
413/8”
383/8”
451/4”
31/8”
125/16” 123/4”
241/2” 263/4” 263/4” 165/8”
69/16”
1411/16”
361/2”
4”
5” 7”
Figure 2. DelRay Fireplace dimensions (Tolerance ± ⅛").
DRL*3613 DIMENSIONS
A B C D
41⁄ 38⁄ 36½ 45¼
DRL*4813 DIMENSIONS
A B C D
53⁄ 50⁄ 48½ 57¼
DRL*6013 DIMENSIONS
A B C D
65⁄ 62½ 60½ 69¼
A
TOP VIEW
FRONT
VIEW
LEFT SIDE RIGHT SIDE
B
C
D
GAS
ELECTRICAL
5⁄

8
Installation
XG0226 - 042220
Section 2: Framing
1). Frame in the enclosure for the unit with framing materials. The
framed opening for the assembled replace shown below in table
NOTE: When constructing the framed opening, please ensure there is
access to install the gas line when the unit is installed
* When sheetrock is used behind the replace, framing depth may be
increased by 1/2".
Clearances must be in accordance with local installation codes and
the requirements of the gas supplier
Figure 3.b Framing dimensions (Straight wall & Corner Installation).Figure 3.a Framing dimensions table
NOTICE
When this appliance is installed directly on ANY combustible other
than wood ooring (carpet, vinyl, etc.). It must be installed on an
equivalent wood or metal panel. This material must extend the full
width and depth of the appliance.
WARNING
In Wall and Corner Dimensions
362
14 1
4"
1101.100
43 3
8"
856
33 11
16 "
1:32
DWG. NO.
SHEET 1 OF 3
WEIGHT:
MNR36 Framing Assembly
Finish
MATERIAL
Revision / Date
Drawn by
DATE
NAME
31/07/2018
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\MNR36 Framing Assembly
March-14-19 11:00:17 AM
SCALE
DM
Description
MNR36 Framing Assembly
Revision
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
12.700
1
2"
12.700
1
2"
1206
47 1
2"
1705
67 1
8"
1101.100
43 3
8"
1:32
DWG. NO.
SHEET 3 OF 3
WEIGHT:
MNR36 Framing Assembly
Finish
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Revision / Date
Drawn by
DATE
NAME
15/08/2018
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\MNR36 Framing Corner Assembly
March-14-19 11:02:44 AM
SCALE
DM
Description
MNR36 Freaming Corner Assembly
Revision
Framing header must
beturnedonedgeto
meetventclearance
DRL*3613 DIMENSIONS
A B C D
43⁄ 67⁄ 47½ 33⁄
DRL*4813 DIMENSIONS
A B C D
55⁄ 79¼ 56⁄ 33⁄
DRL*6013 DIMENSIONS
A B C D
68⁄ 91⁄ 64½ 33⁄
A
D
A
B
C
DRL60 Framing
The DRL60 comes standard
with a non-combustible steel
stud and a heat deector. The
steel stud must be installed at
25" and the stud heat deector
is mounted 3" unerneath the
combustible stud.
26½" when
chase is
ventilated)
26½" when
chase is
ventilated)
25½" to non-
combustible
header
361.950
14 1
4"1751.076
68 15
16 "
856
33 11
16 "
779.780
30 11
16 "
647.700
25 1
2"
COMBUSTIBLE
STUD
NONCOMBUSTIBLE
STUD
HEAT DEFLECTOR
1:24
DWG. NO.
SHEET 1 OF 2
WEIGHT:
MNR60-Framing Assembly
Finish
MATERIAL
Revision / Date
Drawn by
DATE
NAME
03/09/2021
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\DelRay\DelRay Linear\MNR60\CAD Drawings\MNR60-Framing Assembly
Friday, May 13, 2022 1:26:09 PM
SCALE
DM
Description
MNR60-Framing Assembly
Revision
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.

9
Installation
XG0226 - 042220
Clearances
MODEL Top - Top vent† Rear Sides Floor Mantel Vent Pipe
DRL3613*I 21" 2" 1" 0" 6"
1'' all around
2" on the
horizontal
DRL4813*I 21" 2" 1" 0" 6"
1'' all around
2" on the
horizontal
DRL6013*I 21" 2" 1" 0" 6"
1'' all around
2" on the
horizontal
NOTES:
† Clearance from top of replace to a ceiling within the replace
enclosure.
Figure 4. Combustible Wall Clearances
When installing a shelf over the top of the replaces, the following
guidelines must be adhered to:
Recommended flooring considerations
Flooring such as Luxury Vinyl Plank (LVP) and other vinyl ooring can
be sensitive to radiant heat and changes in temperature. If using vinyl
ooring we recommend you install the replace in one of the ways
shown below.
The minimum width of the
hearth is equal to the width of
the replace.
Raise the replace 16” above the
oor to allow for vinyl ooring
to be installed ush to the wall.
(Measured from oor to the
bottom of the door opening)
24" Min.
hearth 16" Min.
rise
Flush
Vinyl
Flooring
Vinyl Flooring
Hearth
Floormountedreplace Raisedreplace
ClearancetoSprinkler
• Maintain 48" of clearance to openings from which heat is
discharged such as chase venting and Cool Wall Advantage.
• Please follow local building codes to determine what sprinkler
head sensor setting is relevant for your installation.
48"

10
Installation
XG0226 - 042220
Standard installation
IMPORTANT
Temperatures are based o of
the minimum enclosure size.
IMPORTANT
Temperatures are based o of
the minimum enclosure size.
NO RECESS
NON-COMBUSTIBLE FACING Enclosure top
Enclosure top
Combustible header
Venting
ports
closed
Combustible facing material not allowed with standard minimum
chase
WARNING
Cement board
Combustible header
TVoverfireplaceinstallation
WORKS FOR TV PLACEMENT ON CHASE
COMBUSTIBLE FACING
45"
MIN.
CHASE
No materials
other than
venting
components
are permitted
in this area

11
Installation
XG0226 - 042220
Vented installation
NO RECESS
COMBUSTIBLE FACING Enclosure top
IMPORTANT
Leaving the
venting ports
open requires
a minimum
chase height
of 6'
VENTED CHASE
See chart for
opening size
Combustible header
Any material protruding into
gray area must be non-
combustible
Combustible Facing material
(Cement board underneath
optional when using a vented
chase)
Venting
ports
open
back wall must be enclosed (no exposed insulation/vapor barrier)
IMPORTANT
Leaving the
venting ports
open requires
a minimum
chase height
of 6'
Venting ports (shown on a DRL3613)
Vented chase opening is mandatory when you open replace vent
ports (all ports must be open).
Vented chase height must be no less than 6'
WARNING
WARNING
1:12
DWG. NO.
SHEET 1 OF 4
WEIGHT:
DRL36
Finish
MATERIAL
Revision / Date
Drawn by
DATE
NAME
3/4/2022
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\DelRay\DelRay Linear\MNR36\CAD Drawings\zExample-MNR36 Framing Assembly
Monday, March 7, 2022 7:58:08 AM
SCALE
JL
Description
DRL36-Fireplace
A
Revision
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Vented installations require that the chase inner wall must be
enclosed (no exposed insulation/vapour barrier) Follow local codes
WARNING
DRL36
Min. chase
opening
70sq inch
DRL48
Min. chase
opening
100sq inch
DRL60
Min. chase
opening
100sq inch

12
Installation
XG0226 - 042220
Section 3: Venting
Montigo oers a variety of direct venting and termination options. The
direct vent termination location MUST be selected such that it is the
highest point in the venting assembly. It should also be selected such
that it provides the shortest vent run possible. Should it be impossible
to ensure that the termination is the highest point or to meet the
venting guidelines laid out below please contact your Montigo dealer
to discuss power venting options.
Notes For Planning Venting:
• Venting originates from the top of the unit
• Venting can terminate through the roof or through an exterior wall.
• Refer to Appendix A - Termination Locations to ensure the planned
termination location is acceptable.
• Once the termination location has been established, refer to the
appropriate section below for installation details
• All replaces shipped from the factory are top vent.
• Silicone application is NOT required when joining Montigo vent
pipes and components.
Under no circumstances can Montigo ex venting be cut to
accommodate an installation. Use an alternative length to complete
your vent run. (Excluding ex included in the MVK05 / MVK05F)
NOTICE
MVK05/MVK05F
MVK05 / MVK05F Flex Vent Kit is a standalone 5' vent kit that
cannot be combined with Montigo Flex or Montigo Rigid pipe to
extend beyond the 5ft of ex included in this kit. The Flex in this
kit can be cut down if shortening is required. Any other venting
conguration beyond the 5ft included in the MVK05 kit will
require going to either Montigo Rigid pipe or Montigo Flex pipe
referenced in the manual pages Venting section.
Figure 4.a MVK05 / MVK05F Flex Vent Kit

13
Installation
XG0226 - 042220
13"
MIN.
DELRAY
UNIT
MTO-4F
OUTDOOR
WALL
FLEX
PIPE
FLOOR
1:32
DWG. NO.
SHEET 1 OF 2
WEIGHT:
MNR36 Complete Assembly
Finish
MATERIAL
Revision / Date
Drawn by
DATE
NAME
26/09/2018
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\MNR36 Complete Assembly
December-18-18 1:38:11 PM
SCALE
DM
Description
DelRay - Venting Assembly.
Revision
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Figure 4.bb Minimum Horizontal vent run (Flex) Figure 4.bb Minimum Horizontal vent run (Rigid)
WallandRoofmountedventing
34'MAXIMUMVERTICALHEIGHT
20'MAXIMUMHORIZONTALOFFSETS
4 MAXIMUM 90° ELBOWS PERMITTED
Theminimum vent system forhorizontal terminationmust consistof:
13" to vent center, then straight out the wall (using ex kit)
The maximum vent system consists of:
34’ vertical length with 4 - 90° bends and a 20’ horizontal length
(measured to center of pipe)
Maximum Vertical vent run:
34’ vertical length with a roof termination,
restrictor recommended.
Maximum Horizontal vent run:
34’ vertical length with 4 elbows, and
the maximum 20 feet horizontal run.
min. 2' vertical.
min. height 6" + 90°
16 1
8"
MIN.
OUTDOOR
WALL
MTO-4F
DELRAY
UNIT
FLOOR
REVISIONS
REV. DESCRIPTION DATE CHANGED BY
- . - -
1:24
DWG. NO.
SHEET 2 OF 2
WEIGHT:
Finish
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Revision / Date
Drawn by
DATE
NAME
26/09/2018
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\MNR36 Complete Assembly
December-18-18 1:38:11 PM
SCALE
DM
Description
DelRay - Venting Assembly.
Revision
MNR36 Complete Assembly
H1
H1
H2
H3
H2
V2
V2
V3
V1
V1
37 1/2'' Min. 40.652'' Min.
HORIZONTAL TABLE
Horizontal
Maximum
H1+H2+H3
16"
2.5'
5'
7.5'
10'
12.5'
15'
17.5'
20'
Vertical
Minimum
V1+V2
13" to Center
1'
2'
3'
4'
5'
6'
7'
8'
VERTICAL TABLE
Horizontal
Maximum
H1+H2
5'
7.5'
10'
12.5'
15'
17.7'
20'
Vertical
Minimum
V1+V2+V3
2'
3'
4'
5'
6'
7'
8'
Section 3-3-1: Venting Layout

14
Installation
XG0226 - 042220
Co-linearventingintoexistingmasonrychimney
Figure 99.a Co-linear top vented conguration.
Hearth
10'
Min.
30'
Max.
Dual 3"
liners
• Maximum 30 feet vertical pipe
• Minimum 10 feet vertical
• Restrictor usage recommended for longer vertical runs
• Keep the exible liner as straight as possible, avoid unnecessary
bending
• A maximum of two certied couplers may be used per length of 3" liner
• DelRay co-linear installation requires reducing from Montigo 4/7
to Duravent 4x6⅝
The appliance can be adapted to co-linear applications using an existing
chimney. The appliance must not be connected to a chimney ue serving
a separate solidfuel burning appliance such as a wood burning replace.
The unit must be fully enclosed while maintaining clearances to
combustibles detailed elsewhere in this manual
NOTICE
46DVA-AD-M1
(Part converts Montigo 4/7 to Duravent 4/6⅝)
46DVA-CLAA
(Converts Duravent Direct vent to Co-Linear)
46DVA-CL33K
(High wind termination)
Co-linear
portion of
vent system
may only be
installed within
the replace
cavity and
chimney.

15
Installation
XG0226 - 042220
FramingwithCoolWallAdvantage
• Refer to the chart below to detemine the length of 5’’ diameter
ex pipe required for completion of installation (12' or 24').
Flex pipe is available from Montigo as part # HDKPDFK and
HDKPDFK-1.
• The installation of this replace must be done by a qualied
and certied gas appliance installer.
• Check local codes and read all instructions prior to
installation.
• Minimum clearance to exible ducting is 1"
UNIT COMPATIBILITY
Cool wall
system
DRL3613NI-* DRL4813NI-* DRL6013NI-*
HDKPD36 
HDKPD48 
HDKPD63 
HDKPD72
HDKSD 
HDKSVD 
HDKPDFK-1 
HDKPDFK  
Cool Wall Advantage Side Discharge Kit horizontal
HDKSD
[Includes 2 louvers , 2 plenums, requires flex kit]
[Includes 2 louvers , 2 plenums, requires flex kit]
Cool Wall Advantage Side Discharge Kit vertical
HDKSVD
[Includes louver , plenum, requires flex kit]
Cool Wall Advantage Kit
HDKPD**
[HDKPDFK-1 is 12’ of 5’’ Diameter flex pipe, HDKPDFK is 24’ of
5’’ Diameter flex pipe]
Cool Wall Flex Kit
HDKPDFK
HDKPDFK-1 An alternate 5-inch diameter duct may be used with this kit
providing it is metal and meet requirements of UL-181 Class 1 Air
Duct. Flexible aluminium duct is acceptable provided it meets the
UL-181 Class 1 requirements.
970
38
3
16 "
51
2"
OPENING
53
21
16 "
1653
65 1
16 "
OPENING
1678
66 1
16 "
76
3"
38
11
2"
533
21"
236
95
16 "
180
71
16 "
1:24
DWG. NO.
SHEET 3 OF 3
WEIGHT:
DL63-Heat distribution TV kit
Finish
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Revision / Date
Drawn by
DATE
NAME
31/03/2017
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\DL63\Cad Drawings\DL63-Heat distribution TV kit
August-23-18 2:12:43 PM
SCALE
DM
Description
DL63 Heat Distribution TV Kit
B
Revision
COOL WALL TV KIT DIMENSIONS
A B C D E F G H I
36" 39⁄"38⁄"3" 1½" N/A 2" 9⁄"N/A 7⁄"
48" 51⁄"50⁄"3" 1½" 30½" 2" 9⁄"21"7⁄"
63" 66⁄"65⁄"3" 1½" 38⁄"2" 9⁄"21"6⁄"
72" 75⁄"74⁄"3" 1½" 39⁄"2" 9⁄"21"7⁄"
A
B
C
D
E
F
2⁄"
970
38 3
16 "
51
2"
OPENING
53
21
16 "
1653
65 1
16 "
OPENING
1678
66 1
16 "
76
3"
38
11
2"
533
21"
236
95
16 "
180
71
16 "
1:24
DWG. NO.
SHEET 3 OF 3
WEIGHT:
DL63-Heat distribution TV kit
Finish
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Revision / Date
Drawn by
DATE
NAME
31/03/2017
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\DL63\Cad Drawings\DL63-Heat distribution TV kit
August-23-18 2:12:43 PM
SCALE
DM
Description
DL63 Heat Distribution TV Kit
B
Revision
G
H
I

16
Installation
XG0226 - 042220
HDKSD PLENUM DIMENSIONS
GRSDH HORIZONTAL AND VERTICAL LOUVER DIMENSIONS
7.943
8.014
.436.436
8.132
.436 .436
15.884
4.036
5.002
8.132
5.002
1:4
DWG. NO.
SHEET 2 OF 2
WEIGHT:
HDC16005-20
Finish
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Revision / Date
Drawn by
DATE
NAME
8/8/2018
20 GA Satin
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\Distinction Accessories\Heat Distribution Channel\HDC16005-20
Wednesday, June 17, 2020 10:26:08 AM
SCALE
DM
Description
Outside Shell
A
Revision
456
17.953
256
10.079
400
15.748
200
7.874
REVISIONS
REV. DESCRIPTION DATE CHANGED BY
- . - -
1:8
DWG. NO.
SHEET 1 OF 1
WEIGHT:
GR0004
Finish
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Revision / Date
Drawn by
DATE
NAME
05/05/2017
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\Distinction Accessories\Heat Distribution Channel\GR0004
October-11-18 6:36:47 AM
SCALE
DM
Description
GRSDV - Sidewall Cavity Venting Louver Vertical
A
Revision
400
15.748
456
17.953
256
10.079
200
7.874
REVISIONS
REV. DESCRIPTION DATE CHANGED BY
- . - -
1:8
DWG. NO.
SHEET 1 OF 1
WEIGHT:
GR0003
Finish
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Revision / Date
Drawn by
DATE
NAME
05/05/2017
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\Distinction Accessories\Heat Distribution Channel\GR0003
October-11-18 6:34:45 AM
SCALE
DM
Description
GRSDH - Sidewall Cavity Venting Louver Horizontal
A
Revision
400
15.748
456
17.953
256
10.079
200
7.874
REVISIONS
REV. DESCRIPTION DATE CHANGED BY
- . - -
1:8
DWG. NO.
SHEET 1 OF 1
WEIGHT:
GR0003
Finish
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Revision / Date
Drawn by
DATE
NAME
05/05/2017
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\Distinction Accessories\Heat Distribution Channel\GR0003
October-11-18 6:34:45 AM
SCALE
DM
Description
GRSDH - Sidewall Cavity Venting Louver Horizontal
A
Revision
400
15.748
456
17.953
256
10.079
200
7.874
REVISIONS
REV. DESCRIPTION DATE CHANGED BY
- . - -
1:8
DWG. NO.
SHEET 1 OF 1
WEIGHT:
GR0003
Finish
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Revision / Date
Drawn by
DATE
NAME
05/05/2017
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\Distinction Accessories\Heat Distribution Channel\GR0003
October-11-18 6:34:45 AM
SCALE
DM
Description
GRSDH - Sidewall Cavity Venting Louver Horizontal
A
Revision

17
Installation
XG0226 - 042220
XT0052 - 190706
Installation
TV Kit Framing
1:12
DWG. NO.
SHEET 3 OF 5
WEIGHT:
DRSQ34
Finish
MATERIAL
Revision / Date
Drawn by
DATE
NAME
2/25/2022
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\DelRay\DelRay Square\DelRay34\Cad Drawings\Example-DRSQ34-Full assembly with TVkits
Wednesday, March 2, 2022 7:08:36 AM
SCALE
JL
Description
DRSQ34-TV KITS WITH FRAME
A
Revision
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
38"
min.
3" min. to
ceiling
6⅝"
1:48
DWG. NO.
SHEET 3 OF 4
WEIGHT:
DRSQ46
Finish
MATERIAL
Revision / Date
Drawn by
DATE
NAME
3/4/2022
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\DelRay\DelRay Square\DelRay46\Cad Darawings\Example-DRSQ46-Full Assembly
Friday, March 4, 2022 2:20:19 PM
SCALE
JL
Description
DRSQ46-TV KITS WITH FRAME
A
Revision
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
HDKPD FRAMING
DIMENSIONS
1:12
DWG. NO.
SHEET 1 OF 4
WEIGHT:
DRL36
Finish
MATERIAL
Revision / Date
Drawn by
DATE
NAME
3/4/2022
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\DelRay\DelRay Linear\MNR36\CAD Drawings\zExample-MNR36 Framing Assembly
Monday, March 7, 2022 7:58:08 AM
SCALE
JL
Description
DRL36-Fireplace
A
Revision
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Unscrew Cap and replace with supplied
Crimp Collars using the same hardware.
REPLACE
REMOVE
WOOD
SCREWS
3 TEK SCREWS FOR
FACEPLATE
SEE DIMENSION
"E" IN TV KIT
DIMENSIONS
3" MIN. TO
CEILING
38" MIN.
FIREPLACE
TO VENT
OPENING
1:48
DWG. NO.
SHEET 2 OF 4
WEIGHT:
DRSQ46
Finish
MATERIAL
Revision / Date
Drawn by
DATE
NAME
3/4/2022
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\DelRay\DelRay Square\DelRay46\Cad Darawings\Example-DRSQ46-Full Assembly
Friday, March 4, 2022 2:20:19 PM
SCALE
JL
Description
DRSQ46-TV KITS
A
Revision
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CRIMP COLLAR
FLEXIBLE DUCTING
CRIMP COLLAR
Secure Heat Distribution kit to Framing at Desired
Height and use supplied crimp collars to secure ducting
with tek screws.
If using Montigo Flex Pipe Kit please ensure that the
pipe is fully extended before cutting to desired length.
Montigo flex pipe can be stretched 50% (e.g. 6’ pipe can
be stretched to 9’)
Maintain 1”
Clearance to
combustibles
from flex pipe.
1
5 6 7
2 3
48" 63" and 72" TV kits have stabilizing
feet that must be attached to the
framing. Refer to the TV Kit dimensional
chart for measurements COMBUSTIBLE
WALL
Leave ¼" gap
between heat
distribution kit
opening and the
wall. Gap will be
covered with the
faceplate
The opening should be a
minimum of 38” from the
top of the fireplace and a
minimum of 3” from the
ceiling.
Secure with 12 wood screws
(not provided)
4Install boards J and K first then secure the TV
kit with the lower screws. Boards L will be cut
to length depending on the height of the Heat
Distribution Kit.
Then install the upper board J to secure the Heat
Distribution Kit.
Faceplate can be painted with a high
temperature paint to match room decor
L L
K
J
see unit
framing
width
FACEPLATE
VENTING PORT COUNT
Fireplaces
D3615NI-2 D4815NI-2 D6315NI-2 D7215NI-2 DRL3613NI-* DRL4813NI-* DRSQ34NI-* DRSQ38NI-* DRSQ42NI-* DRSQ46NI-*
2 venting ports    
4 venting ports      
All venting ports must be connected to a plenum.
WARNING
Unscrew Cap and replace with supplied
Crimp Collars using the same hardware.
REPLACE
REMOVE
XT0052 - 190706
Installation
TV Kit Framing
1:12
DWG. NO.
SHEET 3 OF 5
WEIGHT:
DRSQ34
Finish
MATERIAL
Revision / Date
Drawn by
DATE
NAME
2/25/2022
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\DelRay\DelRay Square\DelRay34\Cad Drawings\Example-DRSQ34-Full assembly with TVkits
Wednesday, March 2, 2022 7:08:36 AM
SCALE
JL
Description
DRSQ34-TV KITS WITH FRAME
A
Revision
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
38"
min.
3" min. to
ceiling
6⅝"
1:48
DWG. NO.
SHEET 3 OF 4
WEIGHT:
DRSQ46
Finish
MATERIAL
Revision / Date
Drawn by
DATE
NAME
3/4/2022
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\DelRay\DelRay Square\DelRay46\Cad Darawings\Example-DRSQ46-Full Assembly
Friday, March 4, 2022 2:20:19 PM
SCALE
JL
Description
DRSQ46-TV KITS WITH FRAME
A
Revision
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
HDKPD FRAMING
DIMENSIONS
1:12
DWG. NO.
SHEET 1 OF 4
WEIGHT:
DRL36
Finish
MATERIAL
Revision / Date
Drawn by
DATE
NAME
3/4/2022
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\DelRay\DelRay Linear\MNR36\CAD Drawings\zExample-MNR36 Framing Assembly
Monday, March 7, 2022 7:58:08 AM
SCALE
JL
Description
DRL36-Fireplace
A
Revision
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Unscrew Cap and replace with supplied
Crimp Collars using the same hardware.
REPLACE
REMOVE
WOOD
SCREWS
3 TEK SCREWS FOR
FACEPLATE
SEE DIMENSION
"E" IN TV KIT
DIMENSIONS
3" MIN. TO
CEILING
38" MIN.
FIREPLACE
TO VENT
OPENING
1:48
DWG. NO.
SHEET 2 OF 4
WEIGHT:
DRSQ46
Finish
MATERIAL
Revision / Date
Drawn by
DATE
NAME
3/4/2022
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\DelRay\DelRay Square\DelRay46\Cad Darawings\Example-DRSQ46-Full Assembly
Friday, March 4, 2022 2:20:19 PM
SCALE
JL
Description
DRSQ46-TV KITS
A
Revision
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CRIMP COLLAR
FLEXIBLE DUCTING
CRIMP COLLAR
Secure Heat Distribution kit to Framing at Desired
Height and use supplied crimp collars to secure ducting
with tek screws.
If using Montigo Flex Pipe Kit please ensure that the
pipe is fully extended before cutting to desired length.
Montigo flex pipe can be stretched 50% (e.g. 6’ pipe can
be stretched to 9’)
Maintain 1”
Clearance to
combustibles
from flex pipe.
1
5 6 7
2 3
48" 63" and 72" TV kits have stabilizing
feet that must be attached to the
framing. Refer to the TV Kit dimensional
chart for measurements COMBUSTIBLE
WALL
Leave ¼" gap
between heat
distribution kit
opening and the
wall. Gap will be
covered with the
faceplate
The opening should be a
minimum of 38” from the
top of the fireplace and a
minimum of 3” from the
ceiling.
Secure with 12 wood screws
(not provided)
4Install boards J and K first then secure the TV
kit with the lower screws. Boards L will be cut
to length depending on the height of the Heat
Distribution Kit.
Then install the upper board J to secure the Heat
Distribution Kit.
Faceplate can be painted with a high
temperature paint to match room decor
L L
K
J
see unit
framing
width
FACEPLATE
VENTING PORT COUNT
Fireplaces
D3615NI-2 D4815NI-2 D6315NI-2 D7215NI-2 DRL3613NI-* DRL4813NI-* DRSQ34NI-* DRSQ38NI-* DRSQ42NI-* DRSQ46NI-*
2 venting ports    
4 venting ports      
All venting ports must be connected to a plenum.
WARNING
CRIMP COLLAR
FLEXIBLE DUCTING
CRIMP COLLAR
Secure Heat Distribution kit to Framing at Desired
Height and use supplied crimp collars to secure ducting
with tek screws.
If using Montigo Flex Pipe Kit please ensure that the
pipe is fully extended before cutting to desired length.
Montigo flex pipe can be stretched 50% (e.g. 6’ pipe can
be stretched to 9’)
Maintain 1”
Clearance to
combustibles
from flex pipe.
1 2
3
VENTING PORT
COUNT
Fireplaces
DRL3613NI-* DRL4813NI-* DRL6013NI-*
2 venting ports 
4 venting ports  
Framing dimensions apply for both horizontal and vertical kits
HDKSD FRAMING DIMENSIONS
Combustible framing
15¾
10¼
DL36090-10
DL36090-10
REVISIONS
REV. DESCRIPTION DATE CHANGED BY
- . - -
1:12
DWG. NO.
SHEET 2 OF 2
WEIGHT:
HDCV16-Cool Wall Discharge Kit Vertical
Finish
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Revision / Date
Drawn by
DATE
NAME
08/08/2018
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\Distinction Accessories\Heat Distribution Channel\HDCV16-Cool Wall Discharge Kit Vertical
June-07-19 12:05:29 PM
SCALE
DM
Description
HDCV16-Cool Wall Discharge Kit Vertical
Revision
Caps from top of
replace
(Onlyforheatkit
installs on units with
only2ventingports)
Attachwithtek
screws
Plenumhas6tabswithngerbendsto
attachtoeitherhorizontalorvertical
framing.Tabscanbesnappedoifnot
needed for screwing to the stud.
Sidewall Kit

18
Installation
XG0226 - 042220
XT0052 - 190706
Installation
TV Kit Framing
1:12
DWG. NO.
SHEET 3 OF 5
WEIGHT:
DRSQ34
Finish
MATERIAL
Revision / Date
Drawn by
DATE
NAME
2/25/2022
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\DelRay\DelRay Square\DelRay34\Cad Drawings\Example-DRSQ34-Full assembly with TVkits
Wednesday, March 2, 2022 7:08:36 AM
SCALE
JL
Description
DRSQ34-TV KITS WITH FRAME
A
Revision
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
38"
min.
3" min. to
ceiling
6
⅝"
1:48
DWG. NO.
SHEET 3 OF 4
WEIGHT:
DRSQ46
Finish
MATERIAL
Revision / Date
Drawn by
DATE
NAME
3/4/2022
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\DelRay\DelRay Square\DelRay46\Cad Darawings\Example-DRSQ46-Full Assembly
Friday, March 4, 2022 2:20:19 PM
SCALE
JL
Description
DRSQ46-TV KITS WITH FRAME
A
Revision
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
HDKPD FRAMING
DIMENSIONS
1:12
DWG. NO.
SHEET 1 OF 4
WEIGHT:
DRL36
Finish
MATERIAL
Revision / Date
Drawn by
DATE
NAME
3/4/2022
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\DelRay\DelRay Linear\MNR36\CAD Drawings\zExample-MNR36 Framing Assembly
Monday, March 7, 2022 7:58:08 AM
SCALE
JL
Description
DRL36-Fireplace
A
Revision
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Unscrew Cap and replace with supplied
Crimp Collars using the same hardware.
REPLACE
REMOVE
WOOD
SCREWS
3 TEK SCREWS FOR
FACEPLATE
SEE DIMENSION
"E" IN TV KIT
DIMENSIONS
3" MIN. TO
CEILING
38" MIN.
FIREPLACE
TO VENT
OPENING
1:48
DWG. NO.
SHEET 2 OF 4
WEIGHT:
DRSQ46
Finish
MATERIAL
Revision / Date
Drawn by
DATE
NAME
3/4/2022
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\DelRay\DelRay Square\DelRay46\Cad Darawings\Example-DRSQ46-Full Assembly
Friday, March 4, 2022 2:20:19 PM
SCALE
JL
Description
DRSQ46-TV KITS
A
Revision
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CRIMP COLLAR
FLEXIBLE DUCTING
CRIMP COLLAR
Secure Heat Distribution kit to Framing at Desired
Height and use supplied crimp collars to secure ducting
with tek screws.
If using Montigo Flex Pipe Kit please ensure that the
pipe is fully extended before cutting to desired length.
Montigo flex pipe can be stretched 50% (e.g. 6’ pipe can
be stretched to 9’)
Maintain 1”
Clearance to
combustibles
from flex pipe.
1
5 6 7
2 3
48" 63" and 72" TV kits have stabilizing
feet that must be attached to the
framing. Refer to the TV Kit dimensional
chart for measurements COMBUSTIBLE
WALL
Leave ¼" gap
between heat
distribution kit
opening and the
wall. Gap will be
covered with the
faceplate
The opening should be a
minimum of 38” from the
top of the fireplace and a
minimum of 3” from the
ceiling.
Secure with 12 wood screws
(not provided)
4Install boards J and K first then secure the TV
kit with the lower screws. Boards L will be cut
to length depending on the height of the Heat
Distribution Kit.
Then install the upper board J to secure the Heat
Distribution Kit.
Faceplate can be painted with a high
temperature paint to match room decor
L L
K
J
see unit
framing
width
FACEPLATE
VENTING PORT COUNT
Fireplaces
D3615NI-2 D4815NI-2 D6315NI-2 D7215NI-2 DRL3613NI-* DRL4813NI-* DRSQ34NI-* DRSQ38NI-* DRSQ42NI-* DRSQ46NI-*
2 venting ports    
4 venting ports      
All venting ports must be connected to a plenum.
WARNING
6⅝"
HDKPD FRAMING
DIMENSIONS
1:12
DWG. NO.
SHEET 1 OF 4
WEIGHT:
DRL36
Finish
MATERIAL
Revision / Date
Drawn by
DATE
NAME
3/4/2022
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\DelRay\DelRay Linear\MNR36\CAD Drawings\zExample-MNR36 Framing Assembly
Monday, March 7, 2022 7:58:08 AM
SCALE
JL
Description
DRL36-Fireplace
A
Revision
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Unscrew Cap and replace with supplied
Crimp Collars using the same hardware.
REPLACE
REMOVE
CRIMP COLLAR
FLEXIBLE DUCTING
CRIMP COLLAR
Secure Heat Distribution kit to Framing at Desired
Height and use supplied crimp collars to secure ducting
with tek screws.
If using Montigo Flex Pipe Kit please ensure that the
pipe is fully extended before cutting to desired length.
Montigo flex pipe can be stretched 50% (e.g. 6’ pipe can
be stretched to 9’)
Maintain 1”
Clearance to
combustibles
from flex pipe.
1 2
3
The opening should be a
minimum of 38” from the
top of the fireplace and a
minimum of 3” from the
ceiling.
Secure with 12 wood screws
(not provided)
4Install boards J and K first then secure the TV
kit with the lower screws. Boards L will be cut
to length depending on the height of the Heat
Distribution Kit.
Then install the upper board J to secure the Heat
Distribution Kit.
L L
K
J
see unit
f r a m i n g
width
TV Kit
38"
min.
3" min. to
ceiling

19
Installation
XG0226 - 042220
WOOD
SCREWS
3 TEK SCREWS FOR
FACEPLATE
SEE DIMENSION
"E" IN TV KIT
DIMENSIONS
3" MIN. TO
CEILING
38" MIN.
FIREPLACE
TO VENT
OPENING
5
6
7
48"63"and72"TVkitshavestabilizing
feetthatmustbeattachedtothe
framing. Refer to the TV Kit dimensional
chart for measurements
COMBUSTIBLE
WALL
Leave ¼" gap
between heat
distribution kit
opening and the
wall. Gap will be
covered with the
faceplate
Faceplate can be painted with a high
temperature paint to match room decor
FACEPLATE
VENTING PORT COUNT
Fireplaces
DRL3613NI-* DRL4813NI-* DRL6013NI-*
2 venting ports 
4 venting ports  
All venting ports must be connected to a plenum.
WARNING
XT0052 - 190706
Installation
TV Kit Framing
1:12
DWG. NO.
SHEET 3 OF 5
WEIGHT:
DRSQ34
Finish
MATERIAL
Revision / Date
Drawn by
DATE
NAME
2/25/2022
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\DelRay\DelRay Square\DelRay34\Cad Drawings\Example-DRSQ34-Full assembly with TVkits
Wednesday, March 2, 2022 7:08:36 AM
SCALE
JL
Description
DRSQ34-TV KITS WITH FRAME
A
Revision
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
38"
min.
3" min. to
ceiling
6⅝"
1:48
DWG. NO.
SHEET 3 OF 4
WEIGHT:
DRSQ46
Finish
MATERIAL
Revision / Date
Drawn by
DATE
NAME
3/4/2022
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\DelRay\DelRay Square\DelRay46\Cad Darawings\Example-DRSQ46-Full Assembly
Friday, March 4, 2022 2:20:19 PM
SCALE
JL
Description
DRSQ46-TV KITS WITH FRAME
A
Revision
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
HDKPD FRAMING
DIMENSIONS
1:12
DWG. NO.
SHEET 1 OF 4
WEIGHT:
DRL36
Finish
MATERIAL
Revision / Date
Drawn by
DATE
NAME
3/4/2022
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\DelRay\DelRay Linear\MNR36\CAD Drawings\zExample-MNR36 Framing Assembly
Monday, March 7, 2022 7:58:08 AM
SCALE
JL
Description
DRL36-Fireplace
A
Revision
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Unscrew Cap and replace with supplied
Crimp Collars using the same hardware.
REPLACE
REMOVE
WOOD
SCREWS
3 TEK SCREWS FOR
FACEPLATE
SEE DIMENSION
"E" IN TV KIT
DIMENSIONS
3" MIN. TO
CEILING
38" MIN.
FIREPLACE
TO VENT
OPENING
1:48
DWG. NO.
SHEET 2 OF 4
WEIGHT:
DRSQ46
Finish
MATERIAL
Revision / Date
Drawn by
DATE
NAME
3/4/2022
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\DelRay\DelRay Square\DelRay46\Cad Darawings\Example-DRSQ46-Full Assembly
Friday, March 4, 2022 2:20:19 PM
SCALE
JL
Description
DRSQ46-TV KITS
A
Revision
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CRIMP COLLAR
FLEXIBLE DUCTING
CRIMP COLLAR
Secure Heat Distribution kit to Framing at Desired
Height and use supplied crimp collars to secure ducting
with tek screws.
If using Montigo Flex Pipe Kit please ensure that the
pipe is fully extended before cutting to desired length.
Montigo flex pipe can be stretched 50% (e.g. 6’ pipe can
be stretched to 9’)
Maintain 1”
Clearance to
combustibles
from flex pipe.
1
5 6 7
2 3
48" 63" and 72" TV kits have stabilizing
feet that must be attached to the
framing. Refer to the TV Kit dimensional
chart for measurements COMBUSTIBLE
WALL
Leave ¼" gap
between heat
distribution kit
opening and the
wall. Gap will be
covered with the
faceplate
The opening should be a
minimum of 38” from the
top of the fireplace and a
minimum of 3” from the
ceiling.
Secure with 12 wood screws
(not provided)
4Install boards J and K first then secure the TV
kit with the lower screws. Boards L will be cut
to length depending on the height of the Heat
Distribution Kit.
Then install the upper board J to secure the Heat
Distribution Kit.
Faceplate can be painted with a high
temperature paint to match room decor
L L
K
J
see unit
framing
width
FACEPLATE
VENTING PORT COUNT
Fireplaces
D3615NI-2 D4815NI-2 D6315NI-2 D7215NI-2 DRL3613NI-* DRL4813NI-* DRSQ34NI-* DRSQ38NI-* DRSQ42NI-* DRSQ46NI-*
2 venting ports    
4 venting ports      
All venting ports must be connected to a plenum.
WARNING

20
Installation
XG0226 - 042220
Roof mounted terminations
The following details are some possible congurations for roof mounted
terminations. See below.
This section applies to installations where the direct vent termination
will be roof mounted.
Section 3-2-1: Venting Layout
Selection of components and details of venting lay out should adhere
to the following guidelines:
• The maximum termination point is 34’ above the replace (NOTE:
if the maximum termination height is used, the ame pattern may
be aected).
• The Vertical termination must be a minimum 2’ higher than where
the termination exits the roong materials, (asphalt shingles, cedar
shakes, etc). This distance should be measured from the high side of
the roof slope where the ue ashing intersects the roong materials.
• Terminationlocationmustbeaminimum6’froma mechanical air inlet.
• For a more detailed diagram of allowed termination locations, see
Appendix A.
• A maximum of two osets (each oset is made up of 2-90° bends) may
be made for vertical vent runs. (2 45° bends are equivalent to 1 90°)
• Firestops must be installed as required by National & local codes.
• Ensure all horizontal runs are supported with a minimum of 3
supports per 10’ of venting.
• Install all roof ashing and storm collars as shown.
Figure 6. Top vent, roof mounted termination with no oset in vent run.
Figure 6.b Top vent, roof mounted with 1 oset (1 oset= two 90° bends).
Section 3-2: Installing a Roof Mounted Direct Vent
Terminationfor4''/7''(MVTK-1)
MVTK1 Termination
MVTK1 Termination
MVTK1 Termination
Storm collar
Storm collar
Storm collar
2' min
2' min
2' min
Support ring
Support ring
Support straps OR
Support ring and
plates
Support ring and
plates
Support plate
Support plate
Firestop
Firestop
Obstacle
Obstacle
Firestop
34' max
34' max
Roof ashing
Roof ashing
Roof ashing
Figure 6.c Top vent, roof mounted with 2 osets (1 oset= two 90° bends).
Firestop
34' max
Firestop