DELTA BREEZ PRO Series User manual

READ AND SAVE THESE INSTRUCTIONS
Address: 46101 Fremont Boulevard, Fremont, CA 94538
US Toll Free Number: 1-888-979-9889
www.deltabreez.com
TABLE OF CONTENTS
Package Contents 2
General Safety Information 3
Preparation and Wiring Diagrams 4
Assembly Instructions 5
Grille Installation 6
Operation 6
Care and Maintenance 7
Troubleshooting 8
Dimensions 9
9
Warranty 10
VENTILATION FAN
MODEL Pro200/Pro300

2
Model:Pro200/ Pro300
PACKAGE CONTENTS
1
2
Grille 1
Part Appearance Quantity
No.
1
2
3
3
Fan body 1
Duct
connector
(6’’)
1
HARDWARE CONTENTS
(Images are to scale)
Long Wood Screw (∅4 x 25)
X 6
X 8
Tapping Screw (∅4 x 10)
Machine Screw (M4 x 6)
Suspension Bracket
X 1
X 4
Rubber
X 4

3Model:Pro200/ Pro300
READ AND SAVE THESE INSTRUCTIONS
GENERAL SAFETY INFORMATION
1. Make sure that the electric service supply voltage is AC
120V, 60Hz.
2. Follow all local electrical and safety codes, as well as
the National Electrical Code (NEC) and the Occupational
Safety and Health Act (OSH Act).
3. Always disconnect the power source before working on or
near the ventilating fan, motor or junction box.
4. Protect the power cord from sharp edges, oil, grease, hot
surfaces, chemicals or other objects.
5. Do not kink the power cord.
6.
shown in Fig. A.
7. Provide suction parts with proper ventilation.
8. This unit is UL listed for use over a bathtub or shower
when installed in a GFCI-protected branch circuit.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
2. Before servicing or cleaning unit, switch power off at
service panel and lock the service disconnecting means
to prevent power from being switched on accidentally.
When the service disconnecting means cannot be
locked, securely fasten a prominent warning device,
such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by
4.
burning equipment to prevent back drafting. Follow the
heating equipment manufacturer’s guideline and safety
standards such as those published by the National
Fire Protection Association (NFPA), and the American
Society of Heating , Refrigerating and Air-Conditioning
Engineers (ASHRAE), and the local code authorities.
5. When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. If this unit is to be installed over a tub or shower, it must
GENERAL SAFETY INFORMATION
be marked as appropriate for the application and be
connected to a GFCI (Ground Fault Circuit Interrupter) –
protected branch circuit.
8. Do not use this unit with any other solid-state control
device. Solid-state controls may cause harmonic
distortion, which can cause a motor humming noise.
(Avertissement: ne convient pas à des régulateurs
de vitesse à semi-conducteurs).
9. NEVER place a switch where it can be reached from a
tub or shower.
10. Not to be installed in a ceiling thermally insulated to a
value greater than R50. (This is required for installation
in Canada only).
CAUTION
1. For General Ventilating Use Only. Do Not Use To Exhaust
Hazardous Or Explosive Materials And Vapors.
2. Not for use in cooking areas. (Fig. B)
3. This product must properly connect to the grounding
conductor of the supply circuit.
4. To reduce the risk of injury to persons, install the fan at
Turning angle too large Duct shrink
ydobehtraenwoblEswobleynamooT
Body
45°
Cooking area
45°
Do not install above or
inside this area
Cooking
Equipment floor
Fig. A
Fig. B

4
Model:Pro200/ Pro300
1. Follow all local electrical and safety codes,
ANSI/NFPA70.
2. NEVER place a switch where it can be reached
from a tub or shower.
3. Connect wires as shown in wiring diagrams.
4. Using wire nuts (not provided), connect the house
power cable to the ventilating fan wires.
5. 14 AWG (2.1 mm²) is the smallest conductor that
shall be used for branch-circuit wiring.
OFF
ON
L
N
POWER SWITCH
JUNCTION BOX SWITCH BOX
WHITE
BLACK
GREEN
GRD
BLACK
ON/OFF SWITCH
(purchase separately) SWITCH BOX
120 VAC
LINE IN
WHITE
GROUND
(bare)
POWER
SWITCH
WIRING
PLATE
PERPARATION AND WIRING DIAGRAMS
Proper insulation around the fan to minimize building
heat loss and gain. The ducting from this fan to the
outside of the building has a strong effect on the air
straightest duct routing possible for best performance,
and avoid installing the fan with smaller ducts than
recommended. Insulation around the ducts can reduce
energy loss and inhibit mold growth. Fans installed with
Roof cap
(with built-in
damper)
Seal gap
around
housing
Caulk termination
to duct
Fan housing
Short piece of flexible
duct helps alignment
and absorbs
sound
or
Wall cap
(with built-in
damper)
Wall cap
(with built-in
damper)
Connect wiring

5Model:Pro200/ Pro300
ASSEMBLY INSTRUCTIONS
Hardware
MOUNT HOUSING WITH SUSPENSION BRACKETS
ATTACH DUCT CONNECTOR
2
1
Tapping screw
Suspension bracket
Rubber
3
WOODEN HEADER
4.
A.Install wooden header between ceiling joists by
using nails or screws.
B.Install the fan body to the wooden header with
long wood screws (Ø 4x25).
A B
16 1/2” 12 1/2”
4
5
DUCT CONNECTION
Ceiling
Fan Body
Tape
Duct
Outside
Gradient
1°~2°
Inside
Duct connector
5. A.Insert the 6” duct (not provided) into the duct
connector and tape all ductwork connections
to make them secure and airtight.
B.Install the duct with a gradient 1°~2° to the
outside.
BEFORE INSTALLATION
Turn off power source. Review all safety precautions.
Machine Screw (M4x6)
3. Suspend fan body with anchor bolts (not provided).
1.Attach the duct connector from outside, and secure it
to fan body by using machine screw (M4x6) .
2. Assemble suspension bracket and rubbers to
fan body, secure them to fan body by using
tapping screws ( Ø4 x 10)
Machine screw
(M4 x 6)
Long wood screw

6
Model:Pro200/ Pro300
GRILLE INSTALLATION
Insert the mounting springs into the slots and
mount the grille to the fan body.
1
Slots
OPERATION
Turn the power switch on , the LED indicator will
be green.

7Model:Pro200/ Pro300
TALLATION
CARE AND MAINTENANCE
TURN OFF POWER SOURCE. REVIEW ALL SAFETY PRECAUTION
See safety information before proceeding. Routine maintenance should be done at least once a year.
1. 1
To remove grille, squeeze springs and pull down.
2. 2
Clean the grille with a cloth.
3
3
3.
Remove dust and dirt from the fan body with a
vacuum cleaner.
Vacuum
cleaner
4
4.
Dampen cloth with dust detergent and wipe the
fan body .Then wipe dry with a clean cloth.
5
5.
Replace grille back onto fan body. Turn on
power source to operate fan again.
• Never use solvents, thinner or harsh chemicals
when cleaning the fan.
• Do not allow water to enter the motor.
• Do not immerse metal parts in water.
• Do not immerse resin parts in water over 140º F.

8
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
The fan is not turning on 1. Power off
2. Faulty switch
3. Faulty wire connection
1. Make sure power supply is on.
2. Test or replace switch.
3. Check wire in switch box.
The fan seems louder
than it should
1. CFM too great
2. Damper not working
properly or damaged
3. Bend in duct too close
to fan discharge
4. Fan discharge
duct
5. Fan body not securely
attached
1. Be sure the CFM rating on the fan matches the
size of your room.
2. Check damper to ensure it is opening and closing
properly. If the damper has become damaged,
please call Customer Service.
3. Be sure you do not have any sharp bends in duct
closer than 18 in. to the fan discharge.
4. Use recommended size ducting to reduce fan
noise.
5. Be sure the fan is securely attached to your ceiling
joists.
The fan is not clearing
the room
1.
airflow within room
2.
1. Be sure a door or window is slightly ajar or opened
2. Be sure the CFM rating on the fan matches the
requirements for your room size.
Model:Pro200/ Pro300

9
DIMENSIONS
PRODUCT SPECIFICATIONS
SPECIFICATIONS
Model No. Voltage
(V)
Frequency
(Hz)
Power @
0.1”SP (W)
Air Flow @
0.1”SP (CFM) Weight (lb.) Max.Current
(amps)
Pro200 120 60 17.5 200 12.6 0.52
Pro300 120 60 41.0 300 12.6 0.72
Model:Pro200/ Pro300
7 5/8"
12
1/4
"
12
1/4
"
15"
15"
6"

10
WARRANTY
DELTA ELECTRONICS THREE YEAR LIMITED WARRANTY
Delta Electronics Inc. (“Delta Electronics”) warrants to the original consumer purchaser in the USA and Canada that
the Breez ventilation fan products will be free from defects in material or workmanship. This warranty is limited to
three (3) years from the original date of purchase.
Limitations and Exclusions
1. During the warranty period, a replacement for any defective product will be supplied free of charge for installation
by the consumer. The warranty provided herein does not cover charges for labor or other costs incurred in the
troubleshooting, repair, removal, and installation service.
2. All returns of defective parts or products must include the product model number, and must be made through an
authorized Delta Electronics distributor. Authorized returns must be shipped prepaid. Repaired or replacement
products will be shipped by Delta Electronics F.O.B. shipping point.
3. Delta Electronics shall not be liable for any indirect, incidental, consequential, punitive, or special damages
arising out of or in connection with products use or performance, regardless of the form of action whether in
contract, tort (including negligence), strict product liability or otherwise.
4.
5. The warranty does not cover if user does not comply with manufacturer’s installation manual.
6. To qualify for warranty service, you must notify Delta Electronics at the address or telephone number below.
7. Delta Electronics shall have no liability to the original owner-user with respect to any defect caused by abuse,
misuse, neglect, improper transportation or storage, improper testing, improper installation, improper operation,
accident of products or parts thereof, or unusual deterioration or degradation of products or parts thereof due to
Address: 46101 Fremont Boulevard, Fremont, CA 94538
US Toll Free Number: 1-888-979-9889
www.deltabreez.com
Model:Pro200/ Pro300