Denver Electronics BTB-410NR User manual

BLUETOOTH SPEAKER WITH LED LIGHTS
Model No.: BTB-410NR
Read this booklet thoroughly before using and save it for future reference
Unit must be fully charged before use
Guide o he Appliance
1

1. TWEETER X 2
2. FUNCT ON/STANDBY
BUTTON
3. P-MODE/M./ECHO BUTTON
4. 10/M./FOLD.- BUTTON
5. /TUN.- BUTTON
6. VOL.- BUTTON
7. /TUN.+ BUTTON
8. VOL.+ BUTTON
9. /PA R/SCAN BUTTON
10. 10/M./FOLD.+ BUTTON
11. EQ/L GHT BUTTON
12. PAR ND CATOR
13. CHARGE ND CATOR
14. LCD D SPLAY
15. SPEAKER X 2
16. HANDLE
17. M C VOL. KNOB
18. 6.3mm M C JACK 1
19. 6.3mm M C JACK 2
20. L GHT BAR
21. 3.5mm AUX N JACK
22. USB PORT
23. POWER ON/OFF BUTTON
24. VENT LAT ON HOLES
25. AC SOCKET
26. Antenna
Ge ing S ar ed
POWER SOURCE
This unit works with rechargeable lead-acid battery (the battery capacity 4000mAh). Fully charge the unit (around 7 hours) before using the product for the
first time. The playback time has about 2 hours after full charging. Unplug the AC Power cord from the AC socket to work on the battery pack after fully
charged. Plugging the AC Power cord while the battery pack is attached initiates the charging of this battery, the charge LED indicator lights red during
charging, when the battery is fully charged the indicator will turn to green. When the unit is with low battery, the LED indicator will flash in red.
Warning: Do not change the battery, only high-qualified personnel can perform this operation.
OPERATION INSTRUCTION
BASIC FUNCTION
TURNING THE UNIT ON/OFF
Press the power ON/OFF button on the rear cabinet to switch the unit on or off.
NOTE: n USB/Bluetooth/AUX mode, when the unit is not providing the main function for around 15 minutes, the unit will automatically switch into standby
mode. Press the FUNCTION/ button to turn on the unit again.
Please note that low volume setting in the audio source may be recognized as “no audio signal”, this will affect the capability of signal detection from the
device and can also originate an automatic switch into standby mode. f this happens please reactivate the audio signal transmission or increase the
volume setting on the audio source player in order to resume playback.
Elec ros a ic Discharge hin s – The unit may reset or may not reset to normal operation mode due to electrostatic discharge, just switch it off and
reconnect again.
SETTING THE FUNCTION MODE
To change the function modes, press the FUNCTION/ button repeatedly to choose USB/AUX/BLUETOOTH/RAD O function.
ADJUSTING THE VOLUME
1. Press the VOL.+ or VOL.- button to increase or decrease the music volume.
2. Rotate the MIC VOL. knob on the unit to increase or decrease the microphone volume.
EQUALIZER (EQ) FUNCTION
This unit has a built-in equalizer system, press the EQ/LIGHT button on unit to select a setting that best matches the music style: FLAT, POP, CLASS C,
JAZZ, and ROCK.
MICROPHONE ECHO ADJUSTMENT
Press and hold the P-MODE/M./ECHO button on unit to turn on or turn off the microphone echo effect. When the echo effect is on, the display will show
“ECHO”.
FLASHING LIGHT
There are 5 modes for the D SCO LED lighting above the speakers. Press and hold the EQ/LIGHT button to choose the desired light mode. To turn off the
light effect, press and hold the EQ/LIGHT button until OFF shows on the display.
L-1: Blue LED will be on constantly when it is selected.
L-2: Blue LED will be on flashing mode.
L-3: Red LED will be on constantly.
L-4: Red LED will be on flashing mode.
L-5: 7 colors LED will be on flashing mode.
There’s a light bar above the handle, the white light on when the Blue/Red LED on constantly, the bar will keep flashing when LED in flashing mode. Press
and hold the EQ/LIGHT button until OFF shows on the display to turn it off together with the disco light.
2

USB OPERATION
1. Press the FUNCTION/ button on unit to select USB mode.
2. Plug the USB memory stick to the USB port on top of the unit. Playback will start automatically.
3. To pause playback, press the PLAY/PAUSE/PAIR/SCAN button on unit. The playing time will flash on the display.
4. To resume playback, press the PLAY/PAUSE/PAIR/SCAN button again.
5. To select a desired track, press the /TUN.+ or /TUN.- button respectively during playing until the desired track appears on the display. The unit
will start play automatically.
6. To search for a particular passage during playback, press and hold the /TUN.+ or /TUN.- button to scan the current playing track at high speed
until desired point (passage) appears, then release the button for normal playback mode.
7. To select a song which track number exceeds 10, press the 10/M./FOLD.+ or 10/M./FOLD.- button each time to skip forward/backward 10 tracks, then
press the /TUN.+ or /TUN.- button to select desired track.
8. To select a desired folder (if the USB contains more than one folder), press and hold the 10/M./FOLD.+ or 10/M./FOLD.- button each time to skip
forward/backward a folder, then press the /TUN.+ or /TUN.- button to select desired track.
Impor an : The USB por is in ended for da a ransfer only, o her devices canno be used wi h his USB connec ion. The use of USB ex ension
cords is no recommended. Don’ plug he USB from he uni when playing or reading he USB device.
REPEAT PLAY
You can play one track or all tracks on the USB repeatedly.
To repea a single rack
1. Press P-MODE/M./ECHO button on unit during play, the display will show “ ” and the current track will be played over an over again.
2. To cancel repeat play, press P-MODE/M./ECHO button on unit until “ ” disappears from the display.
To repea all he racks
1. Press P-MODE/M./ECHO button on unit until the “ ” shows steadily on the display, all tracks on the USB will be played over and over again.
2. To cancel repeat play, press the P-MODE/M./ECHO button on unit until “ ” disappears from the display.
To repea he folder (only for USB which con ains more han one folder)
1. Press the P-MODE/M./ECHO button on unit until “ FOLDER” shows steadily on the display, the current folder will be repeated over and over again.
2. To cancel repeat play, press the P-MODE/M./ECHO button on unit until “ FOLDER” disappears from the display.
RANDOM PLAY
Press the P-MODE/M./ECHO button on unit in play mode till the “RAND” shows steadily on the display, the random play will start from next track
automatically. Press the P-MODE/M./ECHO button on unit again until the “RAND” disappears from the display to cancel.
BLUETOOTH OPERAT ON
1. Press the FUNCTION/ button on unit to switch to BLUETOOTH function, the LCD will display “bt” and the pair indicator will flash at high speed.
2. Turn on the Bluetooth function on the device, scan the unit “BTB-410” and connect, then input the password 0000 if required, the pair indicator keep
light up to indicate connection done, and the display will show “bt”. Press Play to start playback.
3. Adjust the VOLUME on the unit or on the external device to increase or decrease the music volume to your desired level.
4. Press and hold the PLAY/PAUSE/PAIR/SCAN button to disconnect Bluetooth.
Note: The Bluetooth works best within 10 meters in open air.
AUX-IN OPERATION
1. Press the FUNCTION/ button on unit to select the “AUX” mode.
2. Connect your audio device to the AUX N jack on the top panel of the unit with an AUX N cable.(audio cable is not included)
3. Adjust the VOLUME on the unit or on the external device to increase or decrease the music volume to your desired level.
4. Control the playback with your audio device.
MIC JACK OPERATION
Microphone input is available in all modes.
1. Connect your microphone to the two 6.3mm MIC JACK on the unit.
2. Rotate the MIC VOL. knob on the unit to increase or decrease the microphone volume.
3. Press and hold the P-MODE/M./ECHO button to turn on or turn off the microphone echo effect.
Technical Specifica ions
GENERAL
Power Requirements AC100-240V~60/50Hz
Power consumption 33W
Power output MAX 20W X 2
AUX in jack 3.5mm
Microphone jack 6.3mm
Work temperature 5°C - + 40°C
Blue oo h
Communication system Bluetooth Standard version 2.1+EDR
Reception Range 10 meter (line-of-sight distance)
Compatible Bluetooth profiles Advanced Audio Distribution Profile (A2DP)
ACCESSORIES
nstruction Manual x 1pc
3

AC Cord x 1pc
No e: Specifications are subject to change for continuous improvement without prior notice.
4

ALL R GHTS RESERVED, COPYR GHT DENVER ELECTRON CS A/S
Electric and electronic equipment and included batteries contains materials, components and substances that can be hazardous to your health and the
environment, if the waste material (discarded electric and electronic equipment and batteries) is not handled correctly.
Electric and electronic equipment and batteries is marked with the crossed out trash can symbol, seen below. This symbol signifies that electric and
electronic equipment and batteries should not be disposed of with other household waste, but should be disposed of separately.
As the end user it is important that you submit your used batteries to the appropriate and designated facility. n this manner you make sure that the batteries
are recycled in accordance with legislature and will not harm the environment.
All cities have established collection points, where electric and electronic equipment and batteries can either be submitted free of charge at recycling
stations and other collection sites, or be collected from the households. Additional information is available at the technical department of your city.
Hereby, nter Sales A/S declares that the radio equipment type BTB-410NR is in compliance with Directive 2014/53/EU. The full text of the EU declaration
of conformity is available at the following internet address: http://www.denver-electronics.com/denver-btb-410NR/
Operating Frequency Range:2402-2480MHz
Max Output Power:20W×2
mported by:
DENVER ELECTRON CS A/S
Omega 5A, Soeften
DK-8382 Hinnerup
Denmark
www.facebook.com/denverelectronics
5
Table of contents
Other Denver Electronics Speakers manuals