Denver DENVER IPO-1320 User manual

DENVER IP
O
-
1
32
0
DENVER IPC
-
1030

Packing list:
Note: Some models don’t have a separate antenna.
Installation procedure:
Note: For the first time use of IP Camera, please refer to the procedures above.
Connect the Hardware
Install the Search Tool
ogin the IP Camera into AN
ogin the IP Camera to the PC
Client
Access by Mobile
Wireless Settings
End
Start
IP camera Mounting bracket Antenna Power Adaptor
CD Lan cable Installation guide Screws

Connect the camera with Internet cable to the router, and with the power cord to the mains,
like shown above.
PC
Internet Cable
Internet
outer
Power
WAN LAN
IP Camera
PC
Internet
outer
Internet Cable Power
WAN
LAN

1. Installation of the Search Tool
Insert the CD and install the following software:
1. Open the File “IPO-1320 & IPC-1030”, click on “OCX setup” — “Next” — “Install” —
“Finish”
2. Open the File “Search Tool”, Copy the “Search Tool” to the desktop and launch it.
2. ogin of the IP Camera into the AN
After the hardware is connected properly, launch the search tool, and the IP address of the
camera will be displayed automatically.
Note: If the Search Tool issues the message "Subnet mask does not match, please click
N
ext

Double click the camera IP address in the search tool.
In your default browser a login screen like shown below will be displayed:
Note: Both the username and password are “admin”
(Please change the account user name and password for safety later)
After entering the correct user name and password, the ogin screen will be displayed.
(It supports 6 visitors watching online at the same time)
Note: If the OCX already has been installed you may login directly. If not, please install
OCX.
A. Click on “OCX” to download and Install it.
B. efresh the webpage and login again, the camera video will be displayed as below

ive video
3. Wireless Setting
1. Click on the button to access the “Wireless” settings.
2. Search for the WIFI signals and choose the desired SSID.
3. Make sure that all parameters are the same like in your router, enter the WIFI network
key.
4. After 30 seconds click on “Check”, the notification will show you if the WIFI settings are
successful.
5. If correct, just go back to select “Apply”, then disconnect the network cable.
Note: If the camera IP Address can not be found by the search tool, please connect the
internet cable again to check the WIFI settings.

Checking the WIFI signal connection status
4. Device information Setting
1) Click on the icon to access the “ Device information” settings
2) You will see all information for the IP camera

5. Time Settings
1) Click on the icon to access the “Time” settings
2) You may choose any NTP server, then click on “Apply”
3) Choose the desired time and click on “Apply” to activate it
6. Record settings
6.1.Recording in TF card
1) Click on the icon to access the “ ecord” settings
2) Choose “on”
3) Choose between ”First stream” or ”Second stream”
4) Choose the time schedule for recording
5) Click on “Apply”

6.2 Recording to computer disk
1) The main interface into the machine, as shown below;
2) Click on ,select the recording path;
3) Click on ,Start recording.
Note :If you can not change the recording path , please follow these steps:
First ， please open search tool,Find the camera's ip address and copy it :

Then, un IE browser as administrator :
Finally, Paste IP address of the camera in IE browser, Click “Enter”,then you can modify the
video path as below :

7. Alarm Settings & Motion Detection
Configuration
1) First, you should activate the “Motion detection” and choose the display detail that
should be monitored (you may alter the detail as require).
2) You may choose the “Alarm trigger ringtone” and time schedule, then click on ”Apply”,
If the motion detect detects a motion in the configured display detail the alarm bell will
ring (The model without audio function is not provided with this alarm ring tone
notification)

8. Alarm Notification Setting & Email, FTP
1) The email configuration screen serves for the preparation of the alarm function. If the
motion detect activates your camera is triggered, you will receive an email containing
photos. Precondition for this is the correct setup and test of the service. Here the
configuration of a Gmail account as example:
Note: This function only works if the IP camera is connected to the network. If you use Gmail,
you must configure the port as 465, SSL as TLS. But the most important is, that you check if
your email client has SMTP enabled.
After first test email,you will receive an email from google with an login attemt.
Option 2 :
Change your setting to allow less secure apps to access your account,follow these steps :

1.Go to the “Less secure apps ”section in my account.
2.Next to “Access for less secure apps”,select Turn on.(Note to Google Apps users :This
setting is hidden if your administrator has locked less secure app account access)
3.More details about allow less secure apps ,please refer to this link :
https://support.google.com/a/answer/6260879?hl=en.
2) FTP service is a precondition for the alarm function. If the motion detect activates your
camera an email with photos will be submitted to you. For this it is required that you
configure the email service correctly in check it for functionality. For example:
3) Alarm Service Settings, please enter the same settings like in the screenshot below:

9. System log & Net work setting
1). System log is intended for administrators to monitor the system operation
2). In "Network Settings" you may modify the IP address, gateway and port number
10. DDNS Setting
1) Click on the icon and the choose “DDNS Service Settings”.
2) Choose the DDNS server, enter the DDNS user name and password.
3) Submit, refresh, then the DDNS status will be shown as “DDNS Succeed”.

11. PTZ Setting & User Setting
1). Here you may configure some PTZ options

2). Modification of the user password
12. Multiple Settings
1) efresh the device in the LAN search, then you will find other cameras connected to the
same LAN
2) Click on the “2
nd
device”
3) Click on the desired the camera to add it as the 2
nd
device , enter the correct user name and
password
4) Click on “Apply”
5) You may add up to 9 cameras to the multiple settings

13. Maintainance & ONVIF
1) With this option you may restore the camera to its factory settings, and perform
firmware updates.
2) ONVIF Support

14. Auto Snap & Video Mark
1) Capturing of images to the SD card and FTP upload
2) Select the screen detail (you can change the size of the window), click on "Apply" and an
obscured screen area appears
15. Image setting
1) Click on apply to modify the brightness, saturation, sharpness, exposure, contrast
2) Click on the application to modify the exposure mode, infrared lamp,
3) Click on applications to change the value of the I -cut
4) If you click on “Default” all image settings will restored to the default value

FAQ:
A. Password forgotten
1) eset your camera. While the power is on, you must press the ESET button for 10
seconds. The button you will find at the bottom of the camera. With outdoor cameras
the white reset button is located at the end of the power cord.
2) After the reset is completed, the camera is reset to the factory settings, then the
username and the password is "admin".
B. No video, only a black screen, is displayed in the browser
Note: If there is still no live video after running OCX ActiveX, please try to enable the
ActiveX options in the IE security settings by performing the following steps:
1. Deactivate the firewall of your computer.
2. Change the ActiveX settings in “IE” browser > “Tool” > “Internet Options” > “Security” >
“Custom Level” > “ActiveX control and Plug-ins”, all ActiveX options should be
configured as “Enable”:
Especially:
Enable: Download unsigned ActiveX controls

Enable: Initialize and script ActiveX controls not marked as safe
Enable: un ActiveX controls and plug-ins
a.
b.