DesignHouse 523332 User manual

4C
4B
4A
5A
5B
5C OR
1.Shut off water supply. Remove old faucet, taking care not to damage existing water lines. Clean surface in
preparation for newfaucet.
4.Align tabs (4A) and tabs (4B) on quick
connects (4C). Push quick connects firmly
upward and snap onto receiving tube tab.
Pull down moderately to ensure each
connection has been made.
5.Make connectionsto water lines. Use 1/2"
IPS faucet connections (5A) or use coupling
nuts (5C) (notincluded) with
3/8"O.D.ball-nose risers (5B). Use wrenches
to tighten connections. Do not overtighten.
6
45
6.Important: After installation is completed,
remove aerator. Turn on water supply and
allow both hot and cold water to run for at
least one minute each. While water is
running, check for leaks. Replace aerator.
3.Slide hot and cold end valves through sink
mounting holes. Make sure long tubes are
installed away from the spout. Handles
should point out when in off position. The
hot side handle is indicated by a tag with red
printing. Hot side handle should be on the
left. Secure end valves with metal washers
and threaded brackets. Hand tighten
brackets onto shank. Lock brackets into
position by tightening screws.
2.Place flange on bottom of spout body.
Place spout through mounting hole in sink.
Secure spout with washer and nut.
3
2
1-800-558-8700
Mequon, WI 53092
Design House is a registered
brand of DHI Corp.
TWO HANDLE
LAVATORY FAUCET
Models 523332, 523316,523324
silicon sealer
flashlight
faucet supply tubes
basin wrench
Teflon tape
(2) crescent wrenches
Your new Design House faucet will give you years of trouble free performance. Thank you for
choosing our product for your home.
Please read all of these instructions carefully before installing your new faucet.
Helpful tools to install this faucet:
IMPORTANTPOINTS
When installing your new faucet, handtighten the connector nuts, then use one wrench to
anchor the fitting and a second wrench to tighten the nut one additionalturn. Connectionsthat
are too tight will reduce the integrity of the system.
Wrap threaded connections (except aerator thread in spout or where o-ring or rubber sealant
are present) with Teflon tape available from your local hardware or plumbing supply store.
Always wrap in a clockwise direction.
SAFETY TIPS
ALWAYSprotect your eyes with safety glasses.
CONSUMER PROTECTION WARNING
Under the Safe Drinking Water Act, the U.S. Environmental Protection Agency restricts the
amount of lead used in brass and solder. Your new faucet is made in strict compliance with
all government standards. The materials used in the manufacture of this faucet are of industry
standard quality and are similar to other plumbing products having brass fittings.
To reduce the amount of lead in your drinking water, allow the water to run for amoment before
filling your glass andrememberto always use cold water for drinking purposes.
Your new Design House faucet is designedto give you years of trouble free performance. Keep it looking
new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, steel wool and harsh chemicals
that will dull the finish and void your warranty
Brass finishes are polished,then protected with a lacquer coating to help preventtarnishing. Cleanthese
surfaces only with a damp, soft cloth.
INSTALLATION PROCEDURE
MAINTENANCE

3
4
5
2
1
3
2
1
3
4
2
1
Stopper
Flange
Washer
Gasket
Nut
Washer
Tailpiece
Pivot Rod
& Ball
Pivot nut
Washer
Clip
Strap
Screw
1
2
5
4
7
6
3
Problem: Faucet leaks from under handle.
Cause: Bonnet is loose or o-ring on cartridge is
dirty or twisted. Cause: Aerator is incorrectly fitted or is dirty
Problem: Faucet leaks around aerator or an improper
flow pattern.
Action:
1. Unscrew the aerator. Make sure all internal
parts are laying flat.
2. If there is debris, gently flush all parts inside.
3. Reinstall aerator.
Many of these parts come
preassembled. This exploded
diagram is to assist in trouble
shooting.
4
3
3. Remove pivot nut (1). Install horizontal
rod (2) through hole in stopper (3). Hand
tighten pivot nut (1).
4. Attach horizontal rod (1) to strap (2)
using clip (3). Insert lift rod (4) into strap
and tighten screw (5). Pull the lift rod
knob up and down and move the strap
along the horizontal rod to the optimal
location.
2. Apply a small bead of Plumber's putty to
underside of flange (1). Insert body (2) into sink.
Screw flange (1) into body (2). Pivot (3) must
face faucet. Pull assembly down firmly and hold
in place. DO NOT TWIST. Tighten nut,
washer & gasket (4), clean off excess Plumber's
putty .
12
1. Remove stopper (1) and flange (2). Screw
nut (3) all the way down. Push washer (4) and
gasket (5) down. Remove tailpiece (6) from
body (7), add Teflon tape, replace tailpiece.
TROUBLE SHOOTING POP-UP (OPTIONAL) INSTALLATION PROCEDURE
Body
Action:
1. Move handle to OFF position. Remove index
and unscrew the screw on Connector. Then
remove the handle and handle seat.
2.Tighten the bonnet by turning it clockwise. Move
the cartridge stem tothe ON position. The leak
should stop around the cartridge stem.
3. If the leak does not stop, shut off the water supply.
Remove the bonnet by turning it counter clockwise.
Lift cartridge off body and remove cartridge seal.
Clean cartridge ports and cartridge seal. Place
cartridge seal into cartridge ports or replace if
necessary.
4. Replace the cartridge making sure the wingsfit
well into the cuts in the faucet body. Tightly screw
the bonnet onto the faucet body.
5. Reinstall the handle.
Index
Cartridge
Bonnet
Handle Seat
Handle
Connector
screw
Aerator