DesignHouse Ashland 545731 User manual

Your new Design House faucet will give you years of trouble free performance. Thank you for
choosing our product for your home. Please read all of these instructions carefully before
installing your new faucet.
When installing your new faucet, hand tighten the connector nuts, then use one wrench to
anchor the fitting and a second wrench to tighten the nut one additional turn. Connections that
are too tight will reduce the integrity of the system.
Wrap threaded connections (except aerator thread in spout or where o-ring or rubber sealant
are present) with Teflon tape available from your local hardware or plumbing supply store.
Always wrap in a clockwise direction.
IMPORTANT POINTS
SAFETY TIPS
ALWAYS protect your eyes with safety glasses.
Helpful tools to install this faucet:
Teflon tape
(2) crescent wrenches
basin wrench flashlight
faucet supply tubes
silicon sealer
1. Shut off water supplies. Remove the
old faucet. Place the gasket (1A) onto
the bottom of the new faucet assembly.
Place the faucet assembly through the
mounting holes in sink. Secure the
faucet assembly to sink using the
mounting nuts (1B) provided.
Note: If the sink is uneven, use silicone
under the gasket (1A).
2. Making the waterline connections:
Use 1/2 in. I.P.S. faucet connections
(2B, not included), or use the supplied
coupling nuts (2C) with a 3/8 in. O.D.
ball-nose riser (2A, not included). Use
wrenches when tightening. Do not
overtighten.
3. IMPORTANT: After installation is
complete, remove the aerator to flush the
water lines. Do not lose the gasket (3A) in
the aerator. Turn on the water supply and
allow both hot and cold water to run for at
least one minute each. This flushes away
any debris that could cause damage to
internal parts. While the water is running,
check for leaks. Turn off the water and
replace the aerator.
Brass finishes are polished, then protected with a lacquer coating to help prevent tarnishing. Clean these
surfaces only with a damp, soft cloth.
Your new Design House faucet is designed to give you years of trouble free performance. Avoid abrasive
cleaners, steel wool and harsh chemicals that will dull the finish and void your warranty.
CONSUMER PROTECTION WARNING
To reduce the amount of lead in your drinking water, allow the water to run for a moment before
filling your glass and remember to always use cold water for drinking purposes.
Under the Safe Drinking Water Act, the U.S. Environmental Protection Agency restricts the
amount of lead used in brass and solder. Your new faucet is made in strict compliance with
all government standards. The materials used in the manufacture of this faucet are of industry
standard quality and are similar to other plumbing products having brass fittings.
Keep it looking like new by cleaning it periodically with a mild solution of soapy water. Rinse thoroughly and
then dry with a soft cloth.
2C
2A
2B
1B
1A
3A

o 545731 - Polished Chrome
Problem: Faucet leaks from under handle.
Cause: Bonnet is loose or o-ring on cartridge is
dirty or twisted.
Action:
1. Move handle to OFF position. Remove the index
and unscrew the screw on handle, then remove
the handle.
2.Tighten the bonnet by turning it clockwise. Move
the cartridge stem to the ON position. The leak
should stop around the cartridge stem.
3. If the leak does not stop, shut off the water supply.
Remove the bonnet by turning it counter-clockwise.
Lift cartridge off body and remove cartridge seal.
Clean cartridge ports and cartridge seal. Place
cartridge seal into cartridge ports or replace if
necessary.
4. Replace the cartridge making sure the wings fit
well into the cuts in the faucet body. Tightly screw
the bonnet onto the faucet body.
5. Reinstall the handle.
Problem: Faucet leaks around aerator or an improper
flow pattern.
Cause: Aerator is incorrectly fitted or is dirty.
Action:
1. Unscrew the aerator. Make sure all internal parts
are laying flat.
2. If there is debris, gently flush all parts inside.
3. Reinstall the aerator.
Many of these parts come preassembled.
This exploded diagram is to assist in trouble
shooting.
Handle
Bonnet
Coupling nut
Mounting nut
Aerator
(Optional)
Screw
Index
Washer
Disc spring
Disc
Cartridge
Gasket
Connector
(Optional)