DesignHouse 523308 User manual

3.Important: After installation is
completed, remove aerator. Turn
on water supply and allow both
hot and cold water to run for at
least one minute each. While
water is running, check for leaks.
Replace aerator.
2.Make connections to water
lines. Use 1/2" IPS faucet
connections (2A) or use coupling
nuts (2C) (not included) with
3/8"O.D.ball-nose risers (2B).
Use wrenches to tighten
connections. Do not overtighten.
1.Shut off water supplies.
Remove old faucet. Place
gasket (1A) on bottom of new
faucet. Place faucet through
mounting holes in sink. Secure
faucet to sink using mounting
nuts (1B) provided.
3
2
1
1-800-558-8700
Mequon, WI 53092
Design House is a registered
brand of DHI Corp.
TWO HANDLE
LAVATORY FAUCET
Models 523308, 523290,523282
silicon sealer
flashlight
faucet supply tubes
basin wrench
Teflon tape
(2) crescent wrenches
Your new Design House faucet will give you years of trouble free performance. Thank you for
choosing our product for your home.
Please read all of these instructions carefully before installing your new faucet.
Helpful tools to install this faucet:
IMPORTANT POINTS
When installing your new faucet, hand tighten the connector nuts, then use one wrench to
anchor the fitting and a second wrench to tighten the nut one additional turn. Connections that
are too tight will reduce the integrity of the system.
Wrap threaded connections (except aerator thread in spout or where o-ring or rubber sealant
are present) with Teflon tape available from your local hardware or plumbing supply store.
Always wrap in a clockwise direction.
SAFETY TIPS
ALWAYS protect your eyes with safety glasses.
CONSUMER PROTECTION WARNING
Under the Safe Drinking Water Act, the U.S. Environmental Protection Agency restricts the
amount of lead used in brass and solder. Your new faucet is made in strict compliance with
all government standards. The materials used in the manufacture of this faucet are of industry
standard quality and are similar to other plumbing products having brass fittings.
To reduce the amount of lead in your drinking water, allow the water to run for a moment before
filling your glass and remember to always use cold water for drinking purposes.
Your new Design House faucet is designed to give you years of trouble free performance. Keep it looking
new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, steel wool and harsh chemicals
that will dull the finish and void your warranty
Brass finishes are polished, then protected with a lacquer coating to help prevent tarnishing. Clean these
surfaces only with a damp, soft cloth.
INSTALLATION PROCEDURE
MAINTENANCE
1B
1A
2A
2B
2C

4
3
5
2
1
3
2
1
43
2
1
3
6
7
45
2
1
4. Attach horizontal rod (1) to strap (2)
using clip (3). Insert lift rod (4) into strap
and tighten screw (5). Pull the lift rod
knob up and down and move the strap
along the horizontal rod to the optimal
location.
3. Remove pivot nut (1). Install horizontal
rod (2) through hole in stopper (3). Hand
tighten pivot nut (1).
1. Remove stopper (1) and flange (2). Screw
nut (3) all the way down. Push washer (4) and
gasket (5) down. Remove tailpiece (6) from
body (7), add Teflon tape, replace tailpiece.
2. Apply a small bead of Plumber's puttyto
underside of flange (1). Insert body (2) into sink.
Screw flange (1) into body (2). Pivot (3) must
face faucet. Pull assembly down firmly and hold
in place. DO NOT TWIST. Tighten nut,
washer & gasket (4), clean off excess Plumber's
putty .
Stopper
Flange
Washer
Gasket
Nut
Washer
Pivot Rod
& Ball
Pivot nut
Washer
Clip
Strap
Screw
Action:
1. Unscrew the aerator. Make sure all internal
parts are laying flat.
2. If there is debris, gently flush all parts inside.
3. Reinstall aerator.
Problem: Faucet leaks around aerator or an improper
flow pattern.
Cause: Aerator is incorrectly fitted or is dirty
Many of these parts come
preassembled. This exploded
diagram is to assist in trouble
shooting.
4
3
Action:
1. Move handle to OFF position. Remove index
and unscrew the screw on Connector. Then
remove the handle and handle seat.
2.Tighten the bonnet by turning it clockwise. Move
the cartridge stem to the ON position. The leak
should stop around the cartridge stem.
3. If the leak does not stop, shut off the water supply.
Remove the bonnet by turning it counter clockwise.
Lift cartridge off body and remove cartridge seal.
Clean cartridge ports and cartridge seal. Place
cartridge seal into cartridge ports or replace if
necessary.
4. Replace the cartridge making sure the wings fit
well into the cuts in the faucet body. Tightly screw
the bonnet onto the faucet body.
5. Reinstall the handle.
Cause: Bonnet is loose or o-ring on cartridge is
dirty or twisted.
Problem: Faucet leaks from under handle.
12
TROUBLE SHOOTING POP-UP (OPTIONAL) INSTALLATION PROCEDURE
Index
Screw
Connector
Handle
Handle Seat
Bonnet
Cartridge
Washer
Gasket
Mounting Nut
Aerator
Body
Tailpiece