DEVA SENSOR 6BT Product manual

Back Page
Please retain this document
for future reference.
This product should be fitted
in compliance with Water
Regulations, by a qualified
plumber.
Use only a clean damp cloth
to maintain the surface finish,
use of abrasive cleaning
materials will invalidate your
guarantee.
Customer Care ine
0800 1951602
Website
www.deva.org.uk
SENSOR 6BT
SENSOR ACTIVATED TAP - BATTERY POWER
Installation and Maintenance uide
Brooklands Mill
English Street
ancashire
WN73EH
DTC INST190 - 23.9.11

Page 1 Page 6
Installation
InstallationInstallation
Installation
Prior to installation you should fully flush the system to ensure there is no debris in the system
that could cause damage to the product.
Installation should be carried out by a competent installer who after installation should check for
leaks on both the product and the pipe work.
The product must be installed and used in a way as to not cause water damage. Therefore water
from the product must be suitably directed and/or contained.
Sensor Adjustment
Sensor AdjustmentSensor Adjustment
Sensor AdjustmentSensor Adjustment
Sensor AdjustmentSensor Adjustment
Sensor Adjustment
The sensor beam length can be adjusted.
To do this the sensor light panel must be removed from the mixer body.
Once removed a screw is located on the rear of the sensor panel, this can be turned to adjust the
sensor beam length.
Turn the screw clockwise to shorten the beam length.
Replace the sensor panel and ensure correclty located.
Operation
OperationOperation
Operation
Place hand in front of sensor panel to operate, this will allow water to flow.
To mix temperature turn handle on side of mixer to increase or decrease water temeprature.
DTC INST190 - 23.9.11

Page 5 Page 2
Box contents
Box contentsBox contents
Box contents
1. SENSOR 6
2. Rubber washer
3. Back nut
5. ½” x ½” flexi tail
Product features
Product features Product features
Product features
Product is battery operated
Vandal and scratch resistant sensor window
Moisture and water resistant control unit
Battery operation requires 4 x AA batteries
Technical specification
Technical specificationTechnical specification
Technical specification
This product is powered using 4 x AA batteries
The sensing distance for this product is 7 – 23cm
The recommended water pressure range is 0.5 bar – 7.0 bar
The recommended temperature range is 1 oC – 45 oC
Water saving
Water savingWater saving
Water saving
This product is a water saving product by using an infra red sensor to detect when your
hands are in front of the product and turning on the water flow, once your hands are moved
away from the product the sensor will realise this and shut off the water flow.
If the sensor gets blocked by an object then the water will shut off after 70 seconds, to reset
the product remove the obstruction and leave the mixer for 4 seconds. After 4 seconds the product
will have reset and the water should flow again.
DTC INST190 - 23.9.11

Page 3 Page 4
Fitting instructions
Fitting instructionsFitting instructions
Fitting instructions
Step 1
Step 1Step 1
Step 1
Ensure that base o ring is fitted
into the groove in the base plate.
Screw tails into connections in base
of mixer until tight.
Once fitted, then place the tail
through the hole in the basin.
Step 2
Step 2Step 2
Step 2
Once the mixer has been pushed through the hole,
from the underside, push the rubber washer over
tail, follwed by the metal washer.
The connect the back nut onto the tail and screw this
to the underside of the basin.
Position the mixer correctly then tighten the back nut
until the mixer is secure, to provide additional
stability, tighten the two screws fitted in the back
nut.
Step 3
Step 3Step 3
Step 3
Remove the mixer cap, by removing the grub
screw in the rear of the mixer, inside is located
the battery pack.
Remove the top of the pack by removing the
screw, the insert the batteries.
Once fitted replace the pack cap and tighten
screw, then repalce the mixer cap and re-fit
grub screw.
Step 6
Step 6Step 6
Step 6
Connect tails to water supply, hot to
left, cold to right.
Your mixer is now ready to use,
check the sensor by placing
your hand in front of the
sensor, if this does not work,
check that the batteries have
been fitted correctly
DTC INST190 - 23.9.11