Kraus KGW-1700 User manual

INSTALLATION MANUAL
www.kraususa.com I toll free: 1.800.775.0703 I © 2013-2014 Kraus USA Inc.
Single Lever Vessel Glass Waterfall
Bathroom Faucet
KGW-1700

Thank you for your purchase
We would like to take this opportunity to thank you for choosing Kraus.
We hope that you are completely satised with your purchase, and enjoy it for years
to come. If you have any questions, or require technical assistance, please contact
us at 800.775.0703 and one of our representatives will be happy to help.
For more information about Kraus products, please visit:
www.kraususa.com
In order to activate your warranty and get faster access to customer support, please
register your new Kraus product at:
www.kraususa.com/registration
Sincerely,
Kraus USA Customer Service

For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [e-mail]
Prior to Installation:
• Make sure you have all necessary parts by checking the diagram and parts list. If
any part is missing or damaged, please contact Kraus Customer Service at 800-
775-0703 for a replacement
• Turn o the hot and cold water supply at the angle stops and turn on the old
faucet to release any built up pressure. Remove existing faucet. Clean sink or
countertop to remove any debris, plumber’s putty, or silicone
• Place bucket under angle stops. Turn on angle stops to ush any debris prior to
installing new plumbing. Shut o angle stops
• Pre-drilled hole size requirement: 1 3/8” (min)
• Max countertop thickness: 1 3/8”

Diagram and Parts List
1
2
3
4
5
8
96A
6B
6C
6D
7

Diagram and Parts List Tools you will need:
1
10
279
10 31/32”
Minimum distance 90mm
Less than 90mm
Cold Water
32 3/32”
Ø35~Ø38
1
23
10
9
11
12 13
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 13
2
3
4
5
6
7
8
Adjustable Wrench
Phillips Screwdriver
Pipe Tape
1. Decorative Ring
2. Glass Disc
3. Lever
4. Seal for Glass Disc
5. Faucet Body
6. Mounting Hardware
(A) Rubber Washer
(B) Metal Washer
(C) Mounting Nut
(D) Mounting Screws
7. Hot & Cold Waterlines (2)
8. Hex Wrench
9. Manual

Dimensions
7 1/8"
(181mm)
1 1/4"-18UNEF-2A
2 5/16"
(59mm)
1/16"~1 3/4" (1mm~44mm)
2 1/8"
(54mm)
Ø 2 5/8"
(Ø67mm)
5/16"~3/8"
(7.2mm~8.8mm
58.2°
6 1/8"
(155mm)
12.5°
12.5°
11 1/4"
(286mm)
10 7/16"
(265mm)
12 11/16"
(322mm)
3 9/16"
(90mm)
7 11/16"
(195mm)
9/16"-24UNEF-2B
22 1/16"
(560mm)
12.5° 12.5°

Dimensions
7 1/8"
(181mm)
1 1/4"-18UNEF-2A
2 5/16"
(59mm)
1/16"~1 3/4" (1mm~44mm)
2 1/8"
(54mm)
Ø 2 5/8"
(Ø67mm)
5/16"~3/8"
(7.2mm~8.8mm
58.2°
6 1/8"
(155mm)
12.5°
12.5°
11 1/4"
(286mm)
10 7/16"
(265mm)
12 11/16"
(322mm)
3 9/16"
(90mm)
7 11/16"
(195mm)
9/16"-24UNEF-2B
22 1/16"
(560mm)
12.5° 12.5°

Step 1: Remove Mounting Hardware
Remove mounting hardware
(6A, B, C, & D) from the
mounting pipe
Step 2: Remove Decorative Ring
Remove decorative ring (1)
from faucet body (5)
6A
6B
6C
6D
6A
6B
6C
6D
5
5
1
1
2
5
blue Line
Cold
red Line
Hot
Open
Hot Cold
6A
6B
6C
6D
6A
6B
6C
6D
5
5
1
1
2
5
blue Line
Cold
red Line
Hot
Open
Hot Cold

Install glass disc (2) on faucet
body (5). Secure it using
decorative ring (1)
Step 4: Install Faucet
Insert faucet body (1) into
the hole on the countertop.
Attach rubber washer (6A),
metal washer (6B), mounting
nut (6C), and mounting screws
(6D) from underneath the sink
Step 3: Install Glass Disc
6A
6B
6C
6D
6A
6B
6C
6D
5
5
1
1
2
5
blue Line
Cold
red Line
Hot
Open
Hot Cold
6A
6B
6C
6D
6A
6B
6C
6D
5
5
1
1
2
5
blue Line
Cold
red Line
Hot
Open
Hot Cold
NOTE: Hand-tighten only
(decorative ring)

Step 5: Secure Mounting Hardware
Step 6: Connect Waterlines to Main Valve
Adjust direction of faucet body
(5). Tighten mounting nut (6C)
until snug. Tighten mounting
screws (6D) to nut with a
Phillips head screwdriver until
snug
Connect hot and cold waterlines
(7) to the angle stops. Tighten
with a wrench until snug. Turn
on hot and cold angle stops and
check for leaks
6A
6B
6C
6D
6A
6B
6C
6D
5
5
1
1
2
5
blue Line
Cold
red Line
Hot
Open
Hot Cold
6A
6B
6C
6D
6A
6B
6C
6D
5
5
1
1
2
5
blue Line
Cold
red Line
Hot
Open
Hot Cold
6A
6B
6C
6D
6A
6B
6C
6D
5
5
1
1
2
5
blue Line
Cold
red Line
Hot
Open
Hot Cold
NOTE: Make sure O-rings
are installed on both
ends of the hot & cold
waterlines