dewert okin FP2 User manual
I n s t a l l a t i o n I n s t r u c t i o n s
Issue
03/2020
FOOT SWITCH
FP2 - FP4 - FP6
Installation Instructions
(Translation of the original
Installation instructions)
FOOT SWITCH FP
03/2020
ID 49396 4.0
03/2020
ID 49396 4.0
2
1. Designated Use
The FOOT SWITCH FP is designed for connecting to a DewertOkin drive system (see
Installation Instructions supplied with the DewertOkin drive system) to allow motorized
adjustment of ...
Ÿpower-operated beds (range of application EN1970)
Ÿpower-operated beds (range of application EN 60601-2-38)
Ÿpower-operated furniture applications
The FOOT SWITCH FP is not intended for use …
Ÿin the proximity high-frequency surgical equipment and defibrillators,
Ÿin operating theatres (for this purpose IPX8 is required)
Ÿin an environment where inflammable or explosive gases or vapours
(e.g. anaesthetics) are likely to occur,
Ÿin a damp environment, i.e. outdoors
Ÿin beds intended for cleaning in wash tunnels
Ÿand applications in which inadvertent movements are not prevented by appropriate
technical measures.
3
General Information
In the following Installation Instructions the FOOT SWITCH FP2/FP4/FP6 are described
under the code designation FOOT SWITCH.
These instructions are intended for the manufacturer of the end product and are not
designed for passing on to the operator of the end product. With regard to the specialist
information contained herein, these instructions can serve as a basis for drawing up the
instructions for the end products.
It is essential to note the information contained in these instructions! In doing so, you
can prevent mistakes being made on installing or connecting the system which could result
in…
ŸInjury and accidents as well as
Ÿdamage to the drive system or the end product,
Ÿdon't use silicone materials in the proximity of the micro switches.
Only use DewertOkin drive control units!
The DewertOkin drive control units contain an earth-free electric circuit which is insulated
from the supply voltage via double or reinforced insulation.
DewertOkin accepts no liability for damage caused as a result of …
Ÿnon-observance of these instructions,
Ÿ alterations to the product not approved by DewertOkin or …
Ÿ the use of spare parts not manufactured or approved by DewertOkin - these may
not ensure adequate safety!
Due to the policy of ongoing product improvement, DewertOkin reserves the right to carry
out technical changes at any time without prior notification!
2. Prerequisites
The installation steps described in these instructions must be performed by a fully trained
electrical engineer.
ŸThis being the case, you should never carry out this work yourself unless you are a
qualified electrical engineer or
Ÿyou should entrust this work to suitably qualified persons only.
Conformity according to EC Directives
The DewertOkin component, FOOT SWITCH FP, together with controls and drive, is a
machine not ready for use in accordance with the EC Machinery Directive. In other words,
you may not put this drive system into operation until you have met the safety objectives of
the Machinery Directive and issued a corresponding Declaration of Conformity!
The FOOT SWITCH FP together with the DewertOKin drive system meets the safety
objectives of the EC Directives concerning "Low Voltage" and "Electromagnetic
Compatibility (EMC)".
Caution!
When used in the hospital or care sector, only the standards expressly stated in the
additional information (see page 17) have been correspondingly applied. In as far as
standards/requirements to the end product must take additional measures to ensure that
these are met.
Contents page
General Information....................................................................................................... 2
Designated use.............................................................................................................. 3
Prerequisites.................................................................................................................. 3
Getting to Know the System.......................................................................................... 5
Fitting............................................................................................................................. 7
Operation..................... ................................................................................................. 9
Maintenance and Repairs.............................................................................................. 10
Type Label..................................................................................................................... 11
Design of the System..................................................................................................... 12
Troubleshooting............................................................................................................. 13
Cleaning and care.......................................................................................................... 14
EU Declarations of Conformity, Additional Information.................................................. 15
FOOT SWITCH FP
03/2020
ID 49396 4.0
03/2020
ID 49396 4.0
2
1. Designated Use
The FOOT SWITCH FP is designed for connecting to a DewertOkin drive system (see
Installation Instructions supplied with the DewertOkin drive system) to allow motorized
adjustment of ...
Ÿpower-operated beds (range of application EN1970)
Ÿpower-operated beds (range of application EN 60601-2-38)
Ÿpower-operated furniture applications
The FOOT SWITCH FP is not intended for use …
Ÿin the proximity high-frequency surgical equipment and defibrillators,
Ÿin operating theatres (for this purpose IPX8 is required)
Ÿin an environment where inflammable or explosive gases or vapours
(e.g. anaesthetics) are likely to occur,
Ÿin a damp environment, i.e. outdoors
Ÿin beds intended for cleaning in wash tunnels
Ÿand applications in which inadvertent movements are not prevented by appropriate
technical measures.
3
General Information
In the following Installation Instructions the FOOT SWITCH FP2/FP4/FP6 are described
under the code designation FOOT SWITCH.
These instructions are intended for the manufacturer of the end product and are not
designed for passing on to the operator of the end product. With regard to the specialist
information contained herein, these instructions can serve as a basis for drawing up the
instructions for the end products.
It is essential to note the information contained in these instructions! In doing so, you
can prevent mistakes being made on installing or connecting the system which could result
in…
ŸInjury and accidents as well as
Ÿdamage to the drive system or the end product,
Ÿdon't use silicone materials in the proximity of the micro switches.
Only use DewertOkin drive control units!
The DewertOkin drive control units contain an earth-free electric circuit which is insulated
from the supply voltage via double or reinforced insulation.
DewertOkin accepts no liability for damage caused as a result of …
Ÿnon-observance of these instructions,
Ÿ alterations to the product not approved by DewertOkin or …
Ÿ the use of spare parts not manufactured or approved by DewertOkin - these may
not ensure adequate safety!
Due to the policy of ongoing product improvement, DewertOkin reserves the right to carry
out technical changes at any time without prior notification!
2. Prerequisites
The installation steps described in these instructions must be performed by a fully trained
electrical engineer.
ŸThis being the case, you should never carry out this work yourself unless you are a
qualified electrical engineer or
Ÿyou should entrust this work to suitably qualified persons only.
Conformity according to EC Directives
The DewertOkin component, FOOT SWITCH FP, together with controls and drive, is a
machine not ready for use in accordance with the EC Machinery Directive. In other words,
you may not put this drive system into operation until you have met the safety objectives of
the Machinery Directive and issued a corresponding Declaration of Conformity!
The FOOT SWITCH FP together with the DewertOKin drive system meets the safety
objectives of the EC Directives concerning "Low Voltage" and "Electromagnetic
Compatibility (EMC)".
Caution!
When used in the hospital or care sector, only the standards expressly stated in the
additional information (see page 17) have been correspondingly applied. In as far as
standards/requirements to the end product must take additional measures to ensure that
these are met.
Contents page
General Information....................................................................................................... 2
Designated use.............................................................................................................. 3
Prerequisites.................................................................................................................. 3
Getting to Know the System.......................................................................................... 5
Fitting............................................................................................................................. 7
Operation..................... ................................................................................................. 9
Maintenance and Repairs.............................................................................................. 10
Type Label..................................................................................................................... 11
Design of the System..................................................................................................... 12
Troubleshooting............................................................................................................. 13
Cleaning and care.......................................................................................................... 14
EU Declarations of Conformity, Additional Information.................................................. 15
FOOT SWITCH FP
03/2020
ID 49396 4.0
03/2020
ID 49396 4.0
45
The FOOT SWITCH FP is not a medical product - for installing into same, manufacture in
conformity with the EC Directive for "Medical Products" or other regulations is the
responsibility of the manufacturer of the end product. For this purpose, in the case of the
HOSP and CARE versions, DEWERT has additionally applied, fully or partially, a number of
standards from the medical products sector, in order to facilitate use in medical products, e.g.
EN 60601-1 Safety of Electro medical Equipment
EN 60601-1-2 Electromagnetic Compatibility of Electro medical Equipment
EN 60601-2-38 Safety of Hospital Beds
EN 1970 Adjustable Beds for the Disabled
Caution!
For your own safety!
Please ensure when designing your applications that any inadvertent actuation cannot
prove harmful or hazardous. If necessary, appropriate technical measures must be
introduced to prevent any functions which, as a result of inadvertent actuation, could prove
harmful or hazardous.
Avoid subjecting the connection lead to mechanical loads. Regular visual checks of the
connection lead should be carried out at short-term intervals and in particular each time it
has been subjected to a mechanical load.
In the Operating Instructions to be drawn up by yourselves, it is essential that you draw
the operator’s attention to the points mentioned here.
3. Getting to Know the System
The FOOT SWITCH FP is intended for the German market and complies with the Law
applicable in Germany in implementation of relevant EC Directives.
a) Product versions
To put the FOOT SWITCH FP into operation, further components, e.g. drive controls,
main drive (e.g. DUOMAT...) Are required.
b) Standard construction
ŸProtection category: IPX4 (optional IPX6)
ŸColour: housing grey; pedal black
ŸPedals with pimpled, non-slip surface
ŸSection for symbols on the pedal
ŸFunction LED
ŸRidge as foot rest
ŸSection for an individual customer label
1) FOOT SWITCH with 2 pedals
2) FOOT SWITCH with 4 pedals
3) FOOT SWITCH with 6 pedals
Version Possible components in Further DewertOkin
CARE(L)/HOSP(L) versions relay controls
1) 2) 3)
FP2 ; FP4 FP4 SG/S-AG/SGAG MBL
MCL MBK
MBXL CU155
DUOMAT 7
.......
.......
FOOT SWITCH FP
03/2020
ID 49396 4.0
03/2020
ID 49396 4.0
45
The FOOT SWITCH FP is not a medical product - for installing into same, manufacture in
conformity with the EC Directive for "Medical Products" or other regulations is the
responsibility of the manufacturer of the end product. For this purpose, in the case of the
HOSP and CARE versions, DEWERT has additionally applied, fully or partially, a number of
standards from the medical products sector, in order to facilitate use in medical products, e.g.
EN 60601-1 Safety of Electro medical Equipment
EN 60601-1-2 Electromagnetic Compatibility of Electro medical Equipment
EN 60601-2-38 Safety of Hospital Beds
EN 1970 Adjustable Beds for the Disabled
Caution!
For your own safety!
Please ensure when designing your applications that any inadvertent actuation cannot
prove harmful or hazardous. If necessary, appropriate technical measures must be
introduced to prevent any functions which, as a result of inadvertent actuation, could prove
harmful or hazardous.
Avoid subjecting the connection lead to mechanical loads. Regular visual checks of the
connection lead should be carried out at short-term intervals and in particular each time it
has been subjected to a mechanical load.
In the Operating Instructions to be drawn up by yourselves, it is essential that you draw
the operator’s attention to the points mentioned here.
3. Getting to Know the System
The FOOT SWITCH FP is intended for the German market and complies with the Law
applicable in Germany in implementation of relevant EC Directives.
a) Product versions
To put the FOOT SWITCH FP into operation, further components, e.g. drive controls,
main drive (e.g. DUOMAT...) Are required.
b) Standard construction
ŸProtection category: IPX4 (optional IPX6)
ŸColour: housing grey; pedal black
ŸPedals with pimpled, non-slip surface
ŸSection for symbols on the pedal
ŸFunction LED
ŸRidge as foot rest
ŸSection for an individual customer label
1) FOOT SWITCH with 2 pedals
2) FOOT SWITCH with 4 pedals
3) FOOT SWITCH with 6 pedals
Version Possible components in Further DewertOkin
CARE(L)/HOSP(L) versions relay controls
1) 2) 3)
FP2 ; FP4 FP4 SG/S-AG/SGAG MBL
MCL MBK
MBXL CU155
DUOMAT 7
.......
.......
FOOT SWITCH FP
03/2020
ID 49396 4.0
03/2020
ID 49396 4.0
67
4. Fitting
The supply package includes the FOOT SWITCH which, depending on the version ordered,
comes with 2, 4 or 6 adjustment buttons.
a) Fixing and connection
The FOOT SWITCH FP can be fastened to an object with screws (M5, screw length =
thickness of the application + min. 7mm to max. 9mm). Corresponding counternuts (M5) can
already be found in the housing. Insert the connection lead into the corresponding socket in
the control unit or the drive system (see Installation Instructions supplied with the drive
controls). Dimensions of the fixing points (1) according to sketch.
Example: FOOT SWITCH FP2
Example: FOOT SWITCH FP4
c) Technical data (standard)
Rated voltage................................................... : 24 - 29 V DC
Contact rating................................................... : max. 0.2A
Protection classification.................................... : III
Variations.... .......................................... : FP2/FP4/FP6............
Protection category........................................... : IPX4; (optional IPX6)
Colours............................................................. : housing grey; pedal black
Dimensions and weights of the
FOOT SWITCH FP2
Length x width x height..................................... : 220 x 118 x 44 mm
Weight.............................................................. : approx. 0.4 Kg
FOOT SWITCH FP4
Length x width x height..................................... : 802 x 144 x 44 mm
Weight.............................................................. : approx. 0.85 Kg
FOOT SWITCH FP6
Length x width x height..................................... : 511 x 170 x 44 mm
Weight.............................................................. : approx. 1.25 Kg
Ambient conditions for operation, storage and transport
Transport / storage temperature....................... : from -20 °C to +50 °C
from -4 °F to +122 °F
Operating temperature..................................... : from +10 °C to +40 °C+
from +50 °F to +104 °F
Relative humidity.............................................. : from 30% to 75%
Air pressure...................................................... : from 800 hPa to 1060 hPa
Altitude..............................................................: < 2000 m
144
118
8°
511
220
142
16°
142
86
86
130,6
4x M5
4x M5
(1) (1) (1)
(1) (1)
(1)
(1) (1)
118
220 142
86
4xM5
(1)
(1)
(1)
(1)
FOOT SWITCH FP
03/2020
ID 49396 4.0
03/2020
ID 49396 4.0
67
4. Fitting
The supply package includes the FOOT SWITCH which, depending on the version ordered,
comes with 2, 4 or 6 adjustment buttons.
a) Fixing and connection
The FOOT SWITCH FP can be fastened to an object with screws (M5, screw length =
thickness of the application + min. 7mm to max. 9mm). Corresponding counternuts (M5) can
already be found in the housing. Insert the connection lead into the corresponding socket in
the control unit or the drive system (see Installation Instructions supplied with the drive
controls). Dimensions of the fixing points (1) according to sketch.
Example: FOOT SWITCH FP2
Example: FOOT SWITCH FP4
c) Technical data (standard)
Rated voltage................................................... : 24 - 29 V DC
Contact rating................................................... : max. 0.2A
Protection classification.................................... : III
Variations.... .......................................... : FP2/FP4/FP6............
Protection category........................................... : IPX4; (optional IPX6)
Colours............................................................. : housing grey; pedal black
Dimensions and weights of the
FOOT SWITCH FP2
Length x width x height..................................... : 220 x 118 x 44 mm
Weight.............................................................. : approx. 0.4 Kg
FOOT SWITCH FP4
Length x width x height..................................... : 802 x 144 x 44 mm
Weight.............................................................. : approx. 0.85 Kg
FOOT SWITCH FP6
Length x width x height..................................... : 511 x 170 x 44 mm
Weight.............................................................. : approx. 1.25 Kg
Ambient conditions for operation, storage and transport
Transport / storage temperature....................... : from -20 °C to +50 °C
from -4 °F to +122 °F
Operating temperature..................................... : from +10 °C to +40 °C+
from +50 °F to +104 °F
Relative humidity.............................................. : from 30% to 75%
Air pressure...................................................... : from 800 hPa to 1060 hPa
Altitude..............................................................: < 2000 m
144
118
8°
511
220
142
16°
142
86
86
130,6
4x M5
4x M5
(1) (1) (1)
(1) (1)
(1)
(1) (1)
118
220 142
86
4xM5
(1)
(1)
(1)
(1)
FOOT SWITCH FP
03/2020
ID 49396 4.0
03/2020
ID 49396 4.0
8
b) Electrical connection
In the Operating Instructions to be issued by you, point out to the operator that if leads, in
particular the connection lead, are driven over they could sustain damage. Mechanical
loads should also be avoided.
When routing the cables make sure that they
Ÿcannot get entangled or trapped,
Ÿare not subjected to mechanical loads (i.e. do not pull, apply pressure or bend),
Ÿcannot get damaged in any other way.
Make sure that the cables, in particular the connection lead, are fastened to the bed with
adequate strain relief and kink protection and that suitable constructional measures prevent
the mains connection lead from trailing on the floor when the bed is being moved.
9
c) Dismantling
Remove the connection lead from the respective plug socket of the controls or drive system.
Loosen the fastening screws, the FOOT SWITCH FP can be removed.
5. Operation
For drawing up the Operating Instructions for the end product, you can use the specialist
information described herein. Please bear in mind that these instructions are intended for
you as a specialist and not for the possibly non-professional operator of the end product.
Notice: Be sure that your foot is firmly positioned and properly centered over the foot
switch. Pressing the switch with your hand or with the tip of your shoe is incorrect
and not permitted.
a) Prerequisites
The functions of the adjustment buttons are only available provided these are not
inhibited on a locking device or supervisor possibly being used in conjunction with the
equipment. In certain circumstances it may be advisable to block functions in order to
prevent specific movements being carried out.
On the FOOT SWITCH FP …
Ÿthe function LED indicates that a button is pressed. With the CARE L/CARE/
HOSP control unit an error signalling function is supported in addition.
An error (first error) has occurred if
Ÿthe LED does not light up when a key is pressed,
Ÿthe LED glows permanently or
Ÿno signal is emitted from the controls (only CARE/HOSP) or
Ÿa constant signal is emitted from the controls (only CARE/HOSP).
The drive system must then be replaced immediately!
Adjustment buttons
Function LED
FOOT SWITCH FP
03/2020
ID 49396 4.0
03/2020
ID 49396 4.0
8
b) Electrical connection
In the Operating Instructions to be issued by you, point out to the operator that if leads, in
particular the connection lead, are driven over they could sustain damage. Mechanical
loads should also be avoided.
When routing the cables make sure that they
Ÿcannot get entangled or trapped,
Ÿare not subjected to mechanical loads (i.e. do not pull, apply pressure or bend),
Ÿcannot get damaged in any other way.
Make sure that the cables, in particular the connection lead, are fastened to the bed with
adequate strain relief and kink protection and that suitable constructional measures prevent
the mains connection lead from trailing on the floor when the bed is being moved.
9
c) Dismantling
Remove the connection lead from the respective plug socket of the controls or drive system.
Loosen the fastening screws, the FOOT SWITCH FP can be removed.
5. Operation
For drawing up the Operating Instructions for the end product, you can use the specialist
information described herein. Please bear in mind that these instructions are intended for
you as a specialist and not for the possibly non-professional operator of the end product.
Notice: Be sure that your foot is firmly positioned and properly centered over the foot
switch. Pressing the switch with your hand or with the tip of your shoe is incorrect
and not permitted.
a) Prerequisites
The functions of the adjustment buttons are only available provided these are not
inhibited on a locking device or supervisor possibly being used in conjunction with the
equipment. In certain circumstances it may be advisable to block functions in order to
prevent specific movements being carried out.
On the FOOT SWITCH FP …
Ÿthe function LED indicates that a button is pressed. With the CARE L/CARE/
HOSP control unit an error signalling function is supported in addition.
An error (first error) has occurred if
Ÿthe LED does not light up when a key is pressed,
Ÿthe LED glows permanently or
Ÿno signal is emitted from the controls (only CARE/HOSP) or
Ÿa constant signal is emitted from the controls (only CARE/HOSP).
The drive system must then be replaced immediately!
Adjustment buttons
Function LED
FOOT SWITCH FP
03/2020
ID 49396 4.0
03/2020
ID 49396 4.0
10 11
6. Maintenance and Repairs
At regular intervals carry out the inspections. The recommended inspection period is: 6
months
In addition to the above, the following checks should be carried out at shorter intervals:
Ÿ Regular visual checks for damage of all kinds
Check the housing for cracks and fractures and the connection lead for signs
of pinching and shearing-off. Also check the strain relief with kink protection, in
particular after each case of mechanical loading.
Ÿ See also the Installation Instructions supplied with the drive controls and drive
systems.
7. Type Label (Example)
Each drive component carries a type plate giving the exact designation, item number and
technical specifications (for explanation see following figure as an example).
Fußschalter / Footswitch Article type designation
xxxxx Article number
24-29V Input voltage
Prod.Date Week / Year
Serial-No. Serial number
IPX6 Protection category
Use in dry rooms only!
Follow all special disposal instructions!
Mark of CE conformity
FOOT SWITCH FP
03/2020
ID 49396 4.0
03/2020
ID 49396 4.0
10 11
6. Maintenance and Repairs
At regular intervals carry out the inspections. The recommended inspection period is: 6
months
In addition to the above, the following checks should be carried out at shorter intervals:
Ÿ Regular visual checks for damage of all kinds
Check the housing for cracks and fractures and the connection lead for signs
of pinching and shearing-off. Also check the strain relief with kink protection, in
particular after each case of mechanical loading.
Ÿ See also the Installation Instructions supplied with the drive controls and drive
systems.
7. Type Label (Example)
Each drive component carries a type plate giving the exact designation, item number and
technical specifications (for explanation see following figure as an example).
Fußschalter / Footswitch Article type designation
xxxxx Article number
24-29V Input voltage
Prod.Date Week / Year
Serial-No. Serial number
IPX6 Protection category
Use in dry rooms only!
Follow all special disposal instructions!
Mark of CE conformity
FOOT SWITCH FP
03/2020
ID 49396 4.0
03/2020
ID 49396 4.0
12 13
8. Design of the Drive Control System with FOOT SWITCH FP (example)
Example: (Figure: MCL with all additional equipment)
1) Components cannot be used on one and the same controls
Only connect the components as shown !
This can otherwise result in damage to the drive controls!
Pos. Part designation Description
1)
1 DewertOkin locking device Blocking function
or
DewertOkin supervisor Blocking function
2 DewertOkin handset Version depends on application
®
range (e.g.: IPROXX )
3 - 6 DewertOkin slave drive e.g. MEGAMAT, MEGAMAT 2 ...
7 DewertOkin foot switch e.g. FP2, FP4 …
8 DewertOkin control system Drive control unit
1 2 346
57
2 3 4 5 6
17
optional
8
9. Troubleshooting
The following table has been developed to help you detect and eliminate common faults and
errors. If you come across a fault/error that is not listed here, please contact your supplier.
All of these faults/errors may only be inspected and rectified by specialists holding the
qualifications as described on page 3.
Drives suddenly no
longer respond, no
movement takes place
- Fault in the handset
®
IPROXX SE/SE+:
Mode LED lights up in
the blocked state
Mode LED does not
light up in the released
state
No movements can
be carried out, by using
a handset with blocking
function
- Use the magnet to release
The handset
- Handset is blocked. (after a power
®
failure, the IPROXX SE/SE+
handset automatically switches to the
blocked state )
- Locking device or supervisor is blocked
(If being used)
Problem RemedyPossible Cause
- Contact your supplier/dealer
- Contact your supplier/dealer
- Operate drive to move from
the end-of-travel position
- Release the blocking switch
- Relieve the drives
- Connect the system to the
mains to charge the batteries
- Fault in the control system
- End-of-travel position reached
- Blocking switch on control box/
®
Supervisor or IPROXX SE/SE+ set at
“blocked”
- Drive load exceeded
- Battery backup system has reached
total discharge
Function LED in the
handset does not light
up when keys pressed
or glows constantly
(CARE L/CARE/HOSP)
- Contact your supplier/dealer- Contol unit is defectivePermanent or longer-
sounding warning signal
(CARE/HOSP only)
- Leave the drive system in rest
position for approx.
20-30 minutes
- Contact your supplier/dealer
- Check the feeder cable, if
necessary restoring contact
- Thermoswitch on the transformer or in
the control unit has been triggered
- Temperature fuse in transformer
defective
- Miniature fuse has been triggered
- Feeder cable (mains and/or handset/
slave drive) interrupted
FOOT SWITCH or
drive system without
function
- Contact your supplier/dealer
- Connect to the mains
- FOOT SWITCH or drive system
defective
- No supply voltage
FOOT SWITCH FP
03/2020
ID 49396 4.0
03/2020
ID 49396 4.0
12 13
8. Design of the Drive Control System with FOOT SWITCH FP (example)
Example: (Figure: MCL with all additional equipment)
1) Components cannot be used on one and the same controls
Only connect the components as shown !
This can otherwise result in damage to the drive controls!
Pos. Part designation Description
1)
1 DewertOkin locking device Blocking function
or
DewertOkin supervisor Blocking function
2 DewertOkin handset Version depends on application
®
range (e.g.: IPROXX )
3 - 6 DewertOkin slave drive e.g. MEGAMAT, MEGAMAT 2 ...
7 DewertOkin foot switch e.g. FP2, FP4 …
8 DewertOkin control system Drive control unit
1 2 346
57
2 3 4 5 6
17
optional
8
9. Troubleshooting
The following table has been developed to help you detect and eliminate common faults and
errors. If you come across a fault/error that is not listed here, please contact your supplier.
All of these faults/errors may only be inspected and rectified by specialists holding the
qualifications as described on page 3.
Drives suddenly no
longer respond, no
movement takes place
- Fault in the handset
®
IPROXX SE/SE+:
Mode LED lights up in
the blocked state
Mode LED does not
light up in the released
state
No movements can
be carried out, by using
a handset with blocking
function
- Use the magnet to release
The handset
- Handset is blocked. (after a power
®
failure, the IPROXX SE/SE+
handset automatically switches to the
blocked state )
- Locking device or supervisor is blocked
(If being used)
Problem RemedyPossible Cause
- Contact your supplier/dealer
- Contact your supplier/dealer
- Operate drive to move from
the end-of-travel position
- Release the blocking switch
- Relieve the drives
- Connect the system to the
mains to charge the batteries
- Fault in the control system
- End-of-travel position reached
- Blocking switch on control box/
®
Supervisor or IPROXX SE/SE+ set at
“blocked”
- Drive load exceeded
- Battery backup system has reached
total discharge
Function LED in the
handset does not light
up when keys pressed
or glows constantly
(CARE L/CARE/HOSP)
- Contact your supplier/dealer- Contol unit is defectivePermanent or longer-
sounding warning signal
(CARE/HOSP only)
- Leave the drive system in rest
position for approx.
20-30 minutes
- Contact your supplier/dealer
- Check the feeder cable, if
necessary restoring contact
- Thermoswitch on the transformer or in
the control unit has been triggered
- Temperature fuse in transformer
defective
- Miniature fuse has been triggered
- Feeder cable (mains and/or handset/
slave drive) interrupted
FOOT SWITCH or
drive system without
function
- Contact your supplier/dealer
- Connect to the mains
- FOOT SWITCH or drive system
defective
- No supply voltage
FOOT SWITCH FP
03/2020
ID 49396 4.0
03/2020
ID 49396 4.0
14 15
9. Cleaning
The FOOT SWITCH FP has been designed to facilitate cleaning for the user, and this has
been made even easier thanks to the large number of flat surfaces.
The FOOT SWITCH FP should be cleaned with a proprietary cleaning agent suitable for
ABS using a damp cloth. Always note the instructions provided by the manufacturer of the
respective cleaning agent used.
Before cleaning, always pull out the mains plug from the drive system!
Never clean the in a wash tunnel, use a high-pressure cleaner on the FOOT SWITCH FP
controls or spray fluids directly onto them using jets. You risk damaging the equipment!
When cleaning take care not to damage the drive system´s connection lead!
Do not use any solvents such as benzene, alcohol or similar substances.
10. Disposal
The FOOT SWITCH FP consists of electronic components, cables and metal and plastic
parts. You should observe all corresponding national and regional environmental regulations
when disposing of the FOOT SWITCH FP.
The disposal of the product is regulated in Germany by Elektro-G, internationally by the EU
Directive 2012/19/EC (WEEE), or by any applicable national laws and regulations.
The FOOT SWITCH FP should not be disposed of with normal household waste!
EU Declaration of Conformity
In compliance with Appendix IV of the EMC-Directive 2014/30/EU
In compliance with Appendix IV of the LVD-Directive 2014/35/EU
In compliance with Appendix VI of the EU RoHS Directive 2011/65/EU (incl. Commission
delegated Directive (EU) 2015/863)
The manufacturer:
DewertOkin GmbH
Weststraße 1
32278 Kirchlengern
Deutschland - Germany
declares that the following product
FOOT SWITCH FP2/FP4/FP6 with DewertOkin-drive system
meets the requirements of the following EU directives:
Electromagnetic Compatibility Directive 2014/30/EU
Low Voltage Directive 2014/35/EU
COMMISSION DELEGATED DIRECTIVE (EU) 2015/863 of 31 March 2015 amending
Annex II to Directive 2011/65/EU of the European Parliament and of the Council as
regards the list of restricted substances.
Applied standards:
EN 60335-1:2012/A11:2014
EN 55014-1:2006/A1:2009/A2:2011
EN 55014-2:1997/A1:2001/A2:2008
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 62233:2008
This declaration of conformity is no longer valid if constructional changes are made which
significantly change the drive system (i.e., which influence the technical specifications found
in the instructions or the intended use)!
Kirchlengern, Germany 26 March 2020 Dr.-Ing. Josef G. Groß
Managing Director
FOOT SWITCH FP
03/2020
ID 49396 4.0
03/2020
ID 49396 4.0
14 15
9. Cleaning
The FOOT SWITCH FP has been designed to facilitate cleaning for the user, and this has
been made even easier thanks to the large number of flat surfaces.
The FOOT SWITCH FP should be cleaned with a proprietary cleaning agent suitable for
ABS using a damp cloth. Always note the instructions provided by the manufacturer of the
respective cleaning agent used.
Before cleaning, always pull out the mains plug from the drive system!
Never clean the in a wash tunnel, use a high-pressure cleaner on the FOOT SWITCH FP
controls or spray fluids directly onto them using jets. You risk damaging the equipment!
When cleaning take care not to damage the drive system´s connection lead!
Do not use any solvents such as benzene, alcohol or similar substances.
10. Disposal
The FOOT SWITCH FP consists of electronic components, cables and metal and plastic
parts. You should observe all corresponding national and regional environmental regulations
when disposing of the FOOT SWITCH FP.
The disposal of the product is regulated in Germany by Elektro-G, internationally by the EU
Directive 2012/19/EC (WEEE), or by any applicable national laws and regulations.
The FOOT SWITCH FP should not be disposed of with normal household waste!
EU Declaration of Conformity
In compliance with Appendix IV of the EMC-Directive 2014/30/EU
In compliance with Appendix IV of the LVD-Directive 2014/35/EU
In compliance with Appendix VI of the EU RoHS Directive 2011/65/EU (incl. Commission
delegated Directive (EU) 2015/863)
The manufacturer:
DewertOkin GmbH
Weststraße 1
32278 Kirchlengern
Deutschland - Germany
declares that the following product
FOOT SWITCH FP2/FP4/FP6 with DewertOkin-drive system
meets the requirements of the following EU directives:
Electromagnetic Compatibility Directive 2014/30/EU
Low Voltage Directive 2014/35/EU
COMMISSION DELEGATED DIRECTIVE (EU) 2015/863 of 31 March 2015 amending
Annex II to Directive 2011/65/EU of the European Parliament and of the Council as
regards the list of restricted substances.
Applied standards:
EN 60335-1:2012/A11:2014
EN 55014-1:2006/A1:2009/A2:2011
EN 55014-2:1997/A1:2001/A2:2008
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 62233:2008
This declaration of conformity is no longer valid if constructional changes are made which
significantly change the drive system (i.e., which influence the technical specifications found
in the instructions or the intended use)!
Kirchlengern, Germany 26 March 2020 Dr.-Ing. Josef G. Groß
Managing Director
FOOT SWITCH FP
03/2020
ID 49396 4.0
03/2020
ID 49396 4.0
16 17
Additional Information
FOOT SWITCH FP2/FP4/FP6
Based on EN 60601-1:1990 +A1:1993 +A2:1995,
Electro medical Equipment
EN60601-1, section 56.11 Hand-held and foot-operated adjustment devices
Based on EN 60601-1:2006
Electro medical Equipment
EN60601-1, section 15.4.7 Hand-held and foot-operated adjustment devices
Based on EN 60601-2-52:2010
Electro medical Equipment-part 2-52: Particular requirements for basic safety and essential
performance of medical beds
EN60601-2-52, section 201.11.6.5.101 Only in the versions, Protection category min. IPX4
EN60601-2-52, section 201.9.2.2.5 Continuous Activation (Control unit with keypad)
Based on EN1970:2000
Beds for the Disabled
EN1970, in part section 4 Operator’s control with keypad
En1970 section 5.11 Electro technical requirements
Only in the versions, Protection category min. IPX4
Based on EN60601-2-38:1996 +A1:2000,
Power-operated Hospital Beds
EN60601-2-38, section 5.3 Only in the versions, Protection category min. IPX4
EN60601-2-38, section 22.4.101 Control unit with keypad
Notes
FOOT SWITCH FP
03/2020
ID 49396 4.0
03/2020
ID 49396 4.0
16 17
Additional Information
FOOT SWITCH FP2/FP4/FP6
Based on EN 60601-1:1990 +A1:1993 +A2:1995,
Electro medical Equipment
EN60601-1, section 56.11 Hand-held and foot-operated adjustment devices
Based on EN 60601-1:2006
Electro medical Equipment
EN60601-1, section 15.4.7 Hand-held and foot-operated adjustment devices
Based on EN 60601-2-52:2010
Electro medical Equipment-part 2-52: Particular requirements for basic safety and essential
performance of medical beds
EN60601-2-52, section 201.11.6.5.101 Only in the versions, Protection category min. IPX4
EN60601-2-52, section 201.9.2.2.5 Continuous Activation (Control unit with keypad)
Based on EN1970:2000
Beds for the Disabled
EN1970, in part section 4 Operator’s control with keypad
En1970 section 5.11 Electro technical requirements
Only in the versions, Protection category min. IPX4
Based on EN60601-2-38:1996 +A1:2000,
Power-operated Hospital Beds
EN60601-2-38, section 5.3 Only in the versions, Protection category min. IPX4
EN60601-2-38, section 22.4.101 Control unit with keypad
Notes
FOOT SWITCH FP
03/2020
ID 49396 4.0
03/2020
ID 49396 4.0
18
Notes
19
Notes
FOOT SWITCH FP
03/2020
ID 49396 4.0
03/2020
ID 49396 4.0
18
Notes
19
Notes
FOOT SWITCH FP
03/2020
ID 49396 4.0
03/2020
ID 49396 4.0
DewertOkin GmbH
Weststraße 1
32278 Kirchlengern, Germany
Phone: +49 (0)5223/979-0
Fax: +49 (0)5223/75182
http://www.dewertokin.de
FOOT SWITCH FP
03/2020
ID 49396 4.0
03/2020
ID 49396 4.0
This manual suits for next models
2
Table of contents
