DFI TK130 User manual

Multi-Face Fever Detection
User Manual for TK130
Image-F

- 2 -
Version information：
Version
Content
Date
Ver. 1.0
Version 1
2020/6

- 3 -
Table of Contents
1. TK-130 Thermal camera ................................................................................................. 4
2. Installation Requirements ................................................................................................ 4
3. Camera Settings
3.1 Log in to the web interface ..................................................................................... 5
3.2 IP Address settings ................................................................................................. 5
3.3 Global Parameters settings ...................................................................................... 6
4. Notification on EZ Pro
4.1 Install the setup tool ............................................................................................ 10
4.2 Setup tool ........................................................................................................... 12
4.3 EZ Setting ........................................................................................................... 13

- 4 -
1. TK-130 Thermal camera
Main feature
Temperature measurement range: 30-45°C
Working temperature: 10-35°C
Accuracy: ±0.5°C
Resolution:384 × 288
2. Installation Requirements
Mount the TK-130 to the recommended height, approx. 2.5 meters.
The best detect distance between human & camera is approx.2.5-9 meters.

- 5 -
3. Camera Settings
3-1. Log in to the web interface
Key in the camera’s IP with Internet Explorer to enter the web UI.
The default IP Address would be: 192.0.0.64
The default user credentials would be:
User: admin
Password: 12345
3-2. IP Address settings
The factory default IP Address would be: 192.0.0.64
Modifying IP using camera web interface
(1) Go to 【Configuration】>【Network】>【Basic Settings】>【TCP/IP】on
web interface
Set up IPv4 address, subnet mask and gateway here.
Press to save the change

- 6 -
3-3. Global Parameters settings
Before using TK-130 to detect human temperature, you should set up some
parameters
Go to 【Configuration】>【System】>【Maintenance】>【VCA Resource
Type】
Make sure you have choose the Temperature Screening
Live View Parameters
Go to 【Configuration】>【Local】
Enable and save the following settings:

- 7 -
Basic Settings
Go to 【Configuration】>【Temperature Screening】>【Basic Settings】>
【Basic Settings】
Choose Camera 01 , configure and save the following settings:
Please set the distance as the real situation.

- 8 -
Temperature Screening Configuration
Go to 【Configuration】>【Temperature Screening】>【Basic Settings】>
【Temperature Screening Configuration】
Configure Camera 01 (Optical) Settings.
(1) Make sure you have set the temperature to ensure alarm and
pre-alarm.
(2) Press Draw Area to adjust face detection region
(3) Set up Max. and Min. Pupil Distance
You can use the button below the image to set pupil distance. Max and
Min distance refer to camera detection distance.

- 9 -
Configure Camera 02 (Thermal) Settings.
Uncheck Enable Blackbody Correction If no blackbody is used.
Check.
Enable of Body Temperature Compensation and keep parameters as
default.
Manual Calibration can adjust some errors if needed.

- 10 -
4. Notification on EZ Pro
4-1. Install Temperature catcher
To post notification on EZ Pro, we need to install the setup tool first.
(1) Execute the installer.
(2) Follow the steps to finish the installer.

- 11 -

- 12 -
4-2. Temperature Catcher Setting
(1) Execute Temperature catcher.
(2) Set the Camera and EZ Pro server information.
Default camera port would be: 8000.
Press Connect can check the connect status.
Set the Alarm temperature.
Don’t forget to save setting before start service.
(3) Stop service before you need to modify settings.

- 13 -
4-3. EZ Pro Setting
【Camera recording setup】
To use EZ Pro’s push notification function, (including alarm triggering and event
recording etc.), the camera recording should be properly setup first.
(1) Right-click on the camera name and select Camera Settings .
(2) In the 【Recording】tab, turn on the recording and select 【all time
frames】on the “Recording Schedule”
(3) The small red dot next to the camera icon indicates that the camera is
currently recording.

- 14 -
【Adding a new alarm rule】
EZ Pro can receive alarm event from TK-130 and set actions.
(1) Add a new event rule 【Main Menu】> 【System Administration】>
【Event Rules】> 【Add Event Rules】
(2) Setting event rules
Select Generic Event .
Source contains: TK-130

- 15 -
(3) Setting an alarm action
Set an action to be executed by EZ Pro when alarm conditions are met.
(E.g. Play sound , insert bookmark etc.; but only ONE action can be
selected at a time. If the user wants EZ Pro to Play sound and insert
bookmark at the same time, then two event rules are required.)
(4) Click OK and Save to complete alarm settings.