DGA Mach 2 User manual

22 1/2"
29 1/2"
LOCKNUT
BOLT
26"
LOCKNUT BOLT
23"
27"
LOCKNUT
POLE CAP
PLUG
2
"
26 5/8
"
50 1/2"PORTABLE PIPE
SELF TAPPING HEX-HEAD
SCREW and WASHER
(on back of pipe,
in two places)
SELF TAPPING
SCREW and WASHER
(on back of pipe)
21"2"
grade
LOCK
LOCKING
COLLAR
DGA Mach 2™ Permanent Disc Golf Basket Specification Sheet
The Mach II Permanent Disc Pole Hole disc golf basket is an excellent portable target for home, schools, colleges or
any recreational setting. With the inground installation kit the Mach II is also perfect for entry level disc golf courses.
PORTABLE BASE - 3/8”steel rod, welded and hot-dipped galvanized.
6" Sleeve, bolt, nyloninsert locknut and hex head tec screw.
PORTABLE BASE ASSEMBLY INSTRUCTIONS- Place the base on level
ground and insert the short pole into the base with the swedged end
facing up. Line up the pole’s three bottom bolt holes with the three bolt
holes on the base.Push a long bolt through both the base and pole bolt
holes and tighten with a locking nut.
POLE (50 1/2”total length) - Two 1 1/2”I.D., 1 15/16”O.D. hot-dipped
galvanized pipe, drilled. One long pole with cap, one swedged short pole.
POLES - The short pole fits into the base with the swedged end facing up.
The longer pole with the cap side up fits onto the short pole’s swedged
end.The bolt holes on both poles line up and attach with the basket.
TRAPPER BASKET ASSEMBLY - 3/8”steel rod, welded and hot-dipped
galvanized. 6" Sleeve, bolt, hex head nut, nylon insert locknut and hex
head tec screw.
TRAPPER BASKET ASSEMBLY INSTRUCTIONS- Lift the trapper basket up
onto the top of the pole. Slide the trapper basket down past the middle
of the pole and line up the three trapper basket bolt holes with the holes
on the poles.Push a long bolt through the trapper basket and the pole’s
bolt holes.Tighten the long bolt with a locking nut.
CHAIN ASSEMBLY - Welded and hot-dipped galvanized. 12 outer sliding
links and chains, 6 inner pipe protectors and chains. All 18 chains
assembled with heavy duty "S" hooks to allow freer movement of chains.
6" Sleeve , bolt, hex head nut, nylon insert locknut and hex head tec screw.
Rod Assembly - 3/8”. steel rod.
pole. Align holes in collar with holes at top of pole. Fasten with bolt and
nylon insert locknut.
18 "
CONCRETE & RIVER ROCK
15”
grade
LOCK
GRAVEL
2
"
12 " 18 "
IN-GROUND INSTALLATION KIT (Sold Separately)
With the locking tab towards top of collar align
holes in locking collar with holes in pole and
fasten with bolt, head nut and nylon insert
locknut.
Once fastened, the pole can be placed and locked
in anchor.
Anchor
Collar
Basket pole bolted to Collar and locked
to in-ground anchor.
*Note: The LOCKING TAB should always be
pointing at the tee.
DGA | The Founding Company of Disc Golf
DiscGolf.com 831-722-6037

DGA Mach 2™ Permanent Disc Golf Basket Assembly Instructions
Box includes: 1 base, 1 trapper basket, 1 chain holder, 1 long pole with cap, 1 swedged short pole,
3 long bolts (11mm), 3 locking nuts (11mm), 3 short bolts (10mm) and 1 focal point sticker.
You will need 10mm and 11mm wrenches or ratchets to tighten the bolts.
1) Remove all parts from inside the box. Place the base on level ground and insert the short pole into the base with the
swedged end facing up. Line up the poles three bottom bolt holes with the three bolt holes on the base. Push a long
bolt through both the base and pole bolt holes and tighten with a locking nut.
2) Place the longer pole with the cap side up onto the short pole’s swedged end and line up the three bolt holes on
both poles. Lift the trapper basket up onto the top of the pole. Slide the trapper basket down past the middle of the
pole and line up the three trapper basket bolt holes with the holes on the poles. Push a long bolt through the trapper
basket and the pole’s bolt holes. Tighten the long bolt with a locking nut.
3) Lift the chain holder up onto the top of the pole by first feeding the two 4 inch rings that connect to the bottom of
the chain strands. Line up the three bolt holes on the chain holder and the poles top three bolt holes and push a long
bolt through the chain holder and pole bolt holes. Tighten the long bolt with a locking nut.
4) The base, trapper basket and chain holder each have one remaining hole for the 10mm short bolts. In each of the
remaining holes insert and tighten a short bolt to prevent the base, trapper basket and chain holder from wobbling on
the pole.
5) Attach the included focal point sticker so that the top of the sticker is about five inches from the top of the pole.
Start with lining up one end of the sticker so it is straight up and down in line with the pole and slowly wrap the focal
point sticker around the pole. The Mach Lite logo should be facing side ways on the pole.
Base
Trapper Basket
Chain Holder
Short Pole
Swedged
End
Long Pole
with Cap
at Top
Long BoltLocking
Nut
Long boltLocking
Nut
Long Bolt
Locking
Nut
4 Inch
Rings
Short Bolt
Short Bolt
Focal Point
Sticker
Short Bolt
Step 1 Step 2 Step 3 Step 4 Step 5
DGA | The Founding Company of Disc Golf
DiscGolf.com 831-722-6037