Bluegrass Playgrounds 551-510 User manual

551-510 Baseball Backstop without Hood
551-511 Baseball Backstop with Hood
Page 1
Rev 06/18/03
SportsPlay Equipment, Inc. 5642 Natural Bridge, St. Louis, MO 63120 [phone]
IMPORTANT
Please retain this instruction sheet in your files. It contains important maintenance instructions, as well as
replacement parts information.
551-510 WITHOUT HOOD
551-511 WITH HOOD
1
CTN
Hardware Bag
1
CTN
Hardware Bag
9
WF
553-351
Panels
4
PIPE
553-601
2 3/8” OD x 19’0”
4
PIPE
553-601
2 3/8” OD x 19’0”
2
PIPE
553-204
Hood Support
HARDWARE BAG
2
WF
553-352
Panel
4
105-017
2 3/8” Pipe Plug
10
WF
553-351
Panel
24 pr
551-511
1” x 1” Saddle Clamps
HARDWARE BAG
36 pr
555-512
1” x 2 3/8” Saddle
Clamps
4
105-017
2 3/8 OD Pipe Plugs
72
126-505
5/16” x 1 ¼” Carriage
Bolts
36 pr
555-511
1” x 1” Saddle Clamps
24
116-504
5/16” x 1” Hex Bolts
44 pr
555-512
1” x 2 3/8” Saddle Clamps
96
326-501
5/16” Lock Washers
88
126-505
5/16” x 1 ¼” Carriage Bolts
96
216-501
5/16” Hex Nuts
36
116-504
5/16” x 1” Hex Bolts
1
416-400
¼” Socket Key
124
326-501
5/16” Lock Washers
124
216-501
5/16” Hex Nuts
2
196-803
½” x ¾” Socket Set Screw
1
416-500
¼” Socket Key
1 CTN 9 PANEL 4 PIPE
14 Total Pcs. 730# Weight CLASS 70
1 CTN 12 PANEL 6 PIPE
19 Total Pcs. 850# Weight CLASS 70

551-510 Baseball Backstop without Hood
551-511 Baseball Backstop with Hood
Page 2
Rev 06/18/03
SportsPlay Equipment, Inc. 5642 Natural Bridge, St. Louis, MO 63120 [phone]
TOOLS NEEDED FOR THE JOB:
Post Hole Digger Crescent Wrench
Level 5/16” Socket Wrench
10 cu. ft. of Pre-Mix Concrete
GENERAL ASSEMBLY INSTRUCTIONS
1. Check each piece carefully and remove any sharp projections that may have been caused by
shipping.
2. DO NOT Tighten nuts more than hand-tight until the entire assembly is completed.
3. All threaded ends of bolts protruding beyond nuts should be cut off and peened over to
remove any sharp edges.
SPECIFIC ASSEMBLY INSTRUCTIONS:
1. Mark and dig footing holes as shown below.
2. Assemble one center section of backstop on ground with bottom of upright posts at the front
edge of the footing holes.
3. Hand-tighten all bolts securely.
4. Raise assembly into position in footing holes.
5. Assemble each additional section in a similar manner. Raise and attach to sections already in
place.
6. (for 551-511 model only) Add hood sections.
7. Plumb and level backstop. Tighten all bolts securely.
8. Pour footings. Place bricks or old cement chunks below the posts to allow wet cement under
the post.
9. Allow 48 hours for concrete to dry before using the equipment.
MAINTENANCE:
Check periodically for loose bolts and broken parts. Tighten and/or replace immediately.