DIADEMA IMK00001TFT Series Reference manual

1
Built in ice maker and water dispenser
[IMK00001TFT/2TFT series]
Manual for installation, use and maintenance

SAFETY INSTRUCTIONS AND WARNINGS…………………. P.03
PLACEMENT AND INSTALLATION………………………………P.04
AMBIENT TEMPERATURE AND AIR EXCHANGE…………… P.04
WATER CONNECTIONS…………………………………………...P.05
CONNECTING TO THE CO2 CYLINDER……………………………………………………………... P.06
DESCRIPTION AND OPERATION………………………………….. P.07
TFT and FUNCTIONS………………………………………..……….. P.09
EMPTY THE MACHINE………………………………………………..P.09
WATER DISPENSING and ICE PRODUCTION………….………………………………………….. .P.10
OPERATING ANOMALIES……………………………………………………………………………….P 10
DISPOSAL OF APPLIANCES…………………………………………P.11

3
The manufacturer
declines any responsibility towards
persons or objects,
as well as for the proper operation of the
machine, due to failure to follow the
instructions given.
This machine complies with the safety regulations currently in
farce. Incorrect use ofthe machine may lead to persona! injury and
damage to objects.
Please read all the instructions carefully before using the machine
as they contain important information on safety and the use and
maintenance of the machine. This will protect you and prevent
damage to the machine.
CORRECT USE
This machine is designed solely to produce ice cubes and dispense
water. Other types of use are not permitted and may prove
dangerous.
The manufacturer will not be held liable for any damage
caused by incorrect use ofthe machine.
TECHNICAL SAFETY
Before connecting the machine to the power mains, check
carefully to make sure that the voltage and frequency ratings shown
on the rating plate correspond to those of the electrical system.
These values must absolutely correspond in order to avoid damage
to the machine. In case of doubt, contact a qualified electrician.
The electrical safety of the machine is guaranteed only if it is
connected to a standard earth conductor. It is very important to
verify this information with the utmost attention, and in case of
doubt have the electrical system checked by a qualified electrician.
The manufacturer declines all responsibility for any damage
caused to people or things due to the lack or malfunction of the
earth conductor (for example: risk of electrocution).
• Put the machine into operation only after complete installation in
arder to avoid contact with the electrical components. Before
carrying out assembly, disassembly, or daily maintenance of the
machine, always make sure to disconnect the power cable from the
electrical outlet.
• The connection of the machine to the power mains must not be
made using extension cables, as they do not guarantee the
necessary safety of the machine (for example: risk of
overheating).
• Materiai: stainless steel 304
• Main colour: stainless steel
• Other colours available: on request
• Outside dimensions: H 455 x W 595 x D 397 mm
• Built in dimensions: H 450 x W 560 x D 560 mm
• Appliance weight: 29 Kg
• Package dimensions: H 550 x W 700 x D 455 mm
• Gross weight: 33 Kg
• Product volume: 0,18 mc
• Voltage: 220-240 V/ 50/60 Hz
• Noise Level: 40 dBA
• Ice production: 18 Kg/24h
• Rated electrical power: 0,06 kW
• Power supply required: 0,3 amps
• Refrigerant gas: R134A
• The machine can also be flush-mounted in a wall unit (special
accessory). It is not suitable for outdoor use. Considering the heavy
weight of the machine, it is essential for the unit to be adequately
secured to the adjacent wall.
• If the power cable is damaged, it must be replaced by the
manufacturer, its technical service, or by a qualified electrician, in
order to prevent any risk.
• AII installation, maintenance, and repair operations must be
carried out by qualified personnel only. Incorrect installation,
maintenance, and repairs may lead to serious dangers to the user,
for which the manufacturer declines ali responsibility.
• The machine is disconnected from the power mains only when:
-the main switch of the electrical system is switched off;
-the fuse of the home electrical system is completely
disconnected;
-the power plug of the machine is completely removed from the
electrical outlet.
• To disconnect the machine from the power mains, grasp the plug
and remove; do not pull on the powercable.
• Do not open the machine casing for any reason. Touching the
voltage cables or modifying the electrical or mechanical structure
may lead to electrocution. This could also cause disturbance in the
operation of the machine. The manufacturer declines all
responsibility towards persons or things due to failure to observe the
instructions above.
• In the event that the machine has to be installed in combination
with another appliance, it must be separate from the other appliance
by a solid intermediate shelf.
USAGE SAFETY
The appliance is not to be used by person (including children) with
reduced physical, sensoria! or mental capacities, or without
experience or knowledge, unless they benefit, through a person
responsible for their safety, or surveillance or insytructions
regarding the use of the appliance. Children must be overlooked to
ensure they do not play with the appliance.
The manufacturer declines all responsibility for any
damage caused by failure to follow the safety instructions
and precautions.

IMPORTANT NOTE
The installation of the appliance must be carried out exclusively by qualified personnel in compliance
with the regulations in farce.
Considering the heavy weight of the machine, it is essential that the
furniture unit be suitably secured to the wall.
Check to make sure that the opening for housing the machine has the correct dimensions (Fig.1).
Avoid installation near radiators, ovens or any heat source.
PLACEMENT AND INSTALLATION
The installation of the machine must be carried out exclusively by qualified personnel in accordance with current
regulations. Considering the heavy weight of the machine, it is essential that the cabinet is adequately fixed to
the wall.
Check the correspondence of the dimensions of the opening for the housing of the machine; installation in places
with little air exchange and with high temperatures is not recommended, as well as places in direct sunlight or
subject to atmospheric agents. Avoid installation near heat sources. For the correct functioning of the appliance
it is mandatory to guarantee an air chimney behind the appliance itself. It is advisable to provide a grid above
and below [example 1].
AMBIENT TEMPERATURE AND AIR EXCHANGE
The performance of the appliance is guaranteed up to an ambient temperature of 32°C on condition that
adequate air exchange is guaranteed as shown in figure 2.
ATTENTION: to allow the appliance to function correctly, the installation instructions must be strictly applied as
described and illustrated. If this does not happen and malfunctions occur, any necessary assistance will not be
covered by the guarantee.
.
Fig.2

5
IMPORTANT
The machine must only be
installed by qualified
personnel. Due to the weight
of the machine, it is
recommended that two people
carry out this operation.
1) Position the appliance
inside the niche with
the right and left sides
in contact with the side
panels and the sliding
guides fully extended
[fig. 3];
2) Fix the guides to the side walls;
Fig.3
3. Turn on the machine by pressing the main switch on the back;
4. Push the machine all the way down the guides, until it is completely positioned inside the cabinet;
WATER CONNECTIONS
The installation of the appliance must be carried out by qualified personnel. If the water system is new, make sure
it is perfectly free from deposits.
Prevent the risk of clogging or damage: if the water pipe is new or has been inactive for a long time, before
proceeding with the water connection, make sure that the water is clear and free from impurities to avoid damage
to the appliance.
For connection to the water mains [and any CO2 cylinder], use the silicone tubes for food found in the package;
old or used tubes must not be reused.
Note:
- before connecting the silicone tube to the water network, it is recommended that the first jet of water coming out
of the tap of your home water supply is discharged into a container (basin or other) until it is evident in the water
the absence of scale residues, rust or other sediments.
- The pressure of the water mains and therefore of the incoming water is NOT higher and lower than 1.5 BAR [if
higher, it is recommended to have a pressure reducer);

CONNECTION TO THE CO2 CYLINDER [for IMK00002 series models]
Turn the knob counterclockwise to the end (pressure gauge closed);
- screw the pressure gauge onto the cylinder all the way down and quickly so as to avoid slight gas leaks;
- connect the hose (from the machine to the pressure gauge connection);
- turn the knob clockwise (pressure gauge open);
- set the pressure to max 5 bar.
C02 BOTTLE ( optional)
Easily found online or at specialty stores.
- Capacity: 600 gr. (0.6 kg);
- Autonomy: can gassed about 70 liters of water (depending on the degree of carbonation);
- Carbon dioxide (CO2) Food E290;
- Size: 31 cm (h) x 7 (d);
- Full bottle weight: about 2 kg;
- Pressure: 36 bar to 0;
- Thread M11x1;
- Is not rechargeable;
The cylinder must be positioned vertically for a correct release of Co2. The machine is also designed for the use
of large cylinders to be positioned, for example, under the sink or in large compartments.

7
DESCRIPTION AND OPERATION
The machine is set up for domestic use and is designed to produce ice cubes and dispense still and sparkling water.
Other types of use are not intended and could be dangerous. The manufacturer cannot be held responsible for
damage caused by failure to observe the safety instructions and warnings.

activation of natural and sparkling
water
[when provided] – icon 1 - 2
ice production activation/deactivation
selector- icon 3
The machine is intended for domestic use.
The machine supplies ice cubes and glasses of natural and light sparkling water.
Other usage is not allowed and may result dangerous. The manufacturer declines any responsibility
coming from misuse.
FRONT VIEW
01. Ice drawer
02. Pull-out drawer
03. Water nozzle
04. Grill
05. Main switch
DISPLAY TFT - SCREEN FUNCTIONS
06
language choice selector –
icon 4
drawer full indicator –
icon 5
05

9
- The manufacturer declines all responsibility for damage caused by improper use, incorrect use and non-
compliance with the instruction booklet and the information set out below.
- After inserting the power cable, wait at least two hours to allow the oil to flow back into the
compressor. Then turn on the appliance with the general key on the back of the household [05]
- Before turning on the appliance, ask your plumber to connect the silicone hose set up for filling the water;
- For best performance, the ambient temperature should not exceed 32°C. With different temperatures the
machine cannot work correctly.
- Turn on the appliance: activate the main button located on the back of the appliance [fig. 05]
ATTENTION: when you turn it on for the first time, allow the appliance to cool down the water contained in
the internal tank and which will be dispensed. The appliance will then start the first ice making cycle.
NOTE: for the first three cycles, the ice cubes may be small and clear.
We recommend emptying the ice tray every 6-8 hours so that you always have fresh ice.
NATURAL and SPARKLING WATER DISPENSING:
- To dispense both still and sparkling water in the desired quantity, keep the corresponding icon (1 or 2)
pressed as indicated in fig.4;
ATTENTION: we recommend dispensing at least 3-4 glasses of sparkling water to allow the gas to enter
the internal tank. After the first dispensing, the performance of the machine will improve [cooling and
carbonation]. Remember that adding CO2 to carbonate water can change its flavor;
ICE PRODUCTION:
- When the drawer [01] is full, ice production stops automatically and resumes when it is necessary to
replenish the quantity;
- If you want to deactivate the ice making function, simply press the icon 3;
- EMPTY THE MACHINE
If the machine is left off for a long time, please empty it to prevent the formation of mold and bacteria.
Do not use cleaning agents that contain soda, acids, or chlorides! These substances can damage the surface
of the machine. Regular cleaning ensures smooth operation and a long life for your machine. Dry with a soft
cloth to avoid scratches.
To empty the appliance, pull out the lower drawer with grill completely and access the two silicone pipes with
tap. Open both and let the water flow out completely. Then close the taps.
__________________________________________________________________________________________
IMPORTANT:
Steam cleaners must not be used.
After cleaning and before using the machine, make sure that all parts have been put away correctly.

OPERATING ANOMALIES
After dispensing sparkling water a few drops of water could come out of the dispenser, this is due to the presence of Co2 in
the pipes, it is sufficient to let more water flow to stop the bubbles.
If the water is not sparkling enough:
- check that there are at least 4-5 atm on the pressure gauge;
- change the C02 cylinder as it is exhausted;
Malfunction symbols:
E1: lack of water entering the appliance (check that the house water faucet is open or that there are no blockages in
the pipe);
E2: empty the lower tank underneath the ice drawer (use the tap as described on page 8 paragraph EMPTYING THE
MACHINE)
E3: upper internal drawer, dedicated to ice production, does not rotate correctly;
E4: faulty refrigeration system;
E5: general problem with the electrical/hydraulic system;
The machine produces little ice and is transparent:
The temperature in the room and/or inside the cabinet is too high. The machine does not cool properly due to insufficient
ventilation of the cabinet or because it is installed near heat sources

11
European Directive 2002/96/CE on electrical waste and electronic equipment (WEEE) requires that electrical
appliances not be disposed of as unsorted municipal waste. Used appliances must be collected separately to optimize
the reclamation or recycling of the component materials and prevent potential harm to human health and to the
environment.The symbol ofthe cancelled garbage bin is displayed on ali these products to remind users ofthe
obligation of separate collection.
For further information on the correct disposal of electrical appliances, please contact your locaI authorities or the
retailer.
For the correct use of the ice maker, in order to prevent future malfunctions, we invite you to scrupulously follow the
instructions contained in the installation and use manual. Whenever this does not occur and it emerges, from a
subsequent recall intervention at the manufacturer of your appliance, that the malfunction is due precisely to the
incorrect application of the installation, use and maintenance procedures, the transport costs inherent in the
resolution of the problems will be entirely borne by the customer, also as regards the sending by the parent company
of the packaging - if not kept - necessary for the collection of the appliance.

We remind you that the appliance you have chosen is entirely made in Italy with an artisanal production.
Thank you for becoming our customers and for trusting us.
________________________________________________________________________________
Ricordiamo che l'apparecchio che avete scelto è interamente realizzato in Italia con una produzione
artigianale. Grazie per essere diventati nostri clienti e per la fiducia accordataci.