Diamond Vantage TS400 User manual

CAUTION: Read all safety and operating instructions before using this equipment.
This operator’s manual must accompany the equipment at all times.
DIAMOND VANTAGE®
TS400 TILE SAW
OWNER’S MANUAL
www.diamondvantage.com
Manual Part#: 983020075201
03.2020Revision 20001

• 2 • diamondvantage.com
TABLE OF CONTENTS
page
I. GENERAL SAFETY RULES FOR ALL POWER TOOLS 3
II. SYMBOLS 5
III. TECHNICAL SPECIFICATIONS 5
IV. GETTING TO KNOW YOUR SAW 6
V. ACCESSORIES/PARTS 7
VI. BLADE INSTALLATION 8
VII. SAFE OPERATING PRACTICES FOR TILE SAW 9-12
VIII. USING THE CUTTING TABLE 12
IX. ELECTRICAL MOTOR SPECIFICATION 13
X. TROUBLESHOOTING 14
XI. CUTTING DEPTH 15
XII. WARRANTY 15
XIII. REPLACEMENT PARTS LIST 16-20
DIAMOND VANTAGE®TS400 TILE SAW OWNER’S MANUAL
www.diamondvantage.com

• 3 • diamondvantage.com
I. GENERAL SAFETY RULES FOR ALL POWER TOOLS
1. KNOW YOUR POWER TOOL. Read the operator’s manual carefully. Learn the saw’s applications and limitations as well
as the specific potential hazards related to this tool.
2. KEEP GUARDS IN PLACE and in good working order.
3. GROUND ALL TOOLS. If tool is equipped with three-prong plug, it should be plugged into a three-hole electrical
receptacle. If an adapter is used to accommodate a two-prong receptacle, the adapter lug must be attached to a
known ground. Never remove the third prong. Check with a qualified electrician or service personnel if the grounding
instructions are not completely understood or if in doubt as to whether the tool is properly grounded.
4. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are
removed from tool before turning it on.
5. KEEP WORK AREA CLEAN. Cluttered workplace is bound to result in higher risk of injuries. Keep area around machine
clear. DO NOT leave tools or tile pieces on the saw machine while it is in operation.
6. DO NOT OPERATE EQUIPMENT IN DANGEROUS OR HAZARDOUS ENVIRONMENTS. Do not use power tools in damp or wet
locations or expose to rain. Keep the work area well lighted. Do not use tool in the presence of flammable liquids or gases.
7. KEEP CHILDREN AWAY. All visitors and children should be kept at a safe distance from the work area. Maintain a safe
operating distance to other personnel.
8. MAKE SURE WORKSHOP IS CHILDPROOF with padlocks, master switches, or by removing starter keys.
9. KNOW HOW TO STOP THE EQUIPMENT QUICKLY IN CASE OF EMERGENCY.
10. ROTATING PARTS. Keep hands, feet, hair, and clothing away from all moving parts to prevent injury. Never operate
when the motor covers, shrouds, and/or guards are removed.
11. HOT PARTS. Engine components can become extremely hot from operation. To prevent severe burns, do not touch these
areas while the engine is running, or immediately after it is turned off. Never operate the engine with heat shields removed.
12. DO NOT FORCE A TOOL OR AN ATTACHMENT to do a job that it was not designed to do. NEVER tamper with the
governor components or settings to increase the maximum speed. Severe personal injury and damage to the engine or
equipment can result if operated at speeds above maximum.
13. SECURE WORK. Always place a work piece flat on table assembly and securely against fence. Using a clamp or a vise
to hold work piece would be helpful.
14. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties or jewelry that may get caught in moving parts.
Non-slip footwear is recommended. Wear protective hair covering to contain long hair.
15. PERSONAL PROTECTIVE EQUIPMENT. Always wear approved respiratory, head, ear and eye protection when operating
this machine. Always use safety glasses. Wear safety glasses with side shields (must comply with ANSI Z87.1) at all
times. Everyday eyeglasses only have impact resistant lenses; they are NOT safety glasses. Use face or dust mask if
cutting operation is dusty, and ear protectors (plugs or muffs) during extended periods of operation.
WARNING!
READ AND FOLLOW ALL SAFETY, OPERATING AND MAINTENANCE INSTRUCTIONS BEFORE USING THE TOOL. Failure to read
and follow these instructions could result in injury or death to you or others as well as damage to the tool and/or reduced
equipment life. Safety warnings and guidelines do not by themselves eliminate danger. They are not substitutes for proper
accident prevention procedures and good judgment. It is the operator’s responsibility to use this machine under safe working
conditions and conform with federal, state and local codes or regulations pertaining to safety, air, pollution, noise etc.

• 4 • diamondvantage.com
16. DON’T OVERREACH. Keep proper footing and balance at all times.
17. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance.
18. DISCONNECT TOOL. When not in use, before servicing, or when changing attachments—wheels, bits, cutters, etc—all
tools should be disconnected.
19. AVOID ACCIDENTAL STARTING. Be sure switch is off when plugging in.
20. USE RECOMMENDED ACCESSORIES. Consult the operator’s manual for recommended accessories. The use of
improper accessories may risk injury.
21. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally
contacted.
22. CHECK THE TOOL FOR DAMAGED PARTS BEFORE A FURTHER USE. Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other
part that is damaged must be properly repaired or replaced by an authorized service center to avoid risk of personal
injury. Always check the machine for loose bolts before starting.
23. NEVER LEAVE TOOL RUNNING UNATTENDED. After machine is switched “off”, do not leave tool until it comes to a
complete stop.
24. USE THE CORRECT EXTENSION CORDS. When using an extension cord, be sure to use one heavy enough to carry the
current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and
overheating. Extension cord tables (refer to page 13) show the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage numbers the heavier the cord.
25. DO NOT ABUSE CORD. Never yank cord to disconnect from electrical outlet. Keep cord away from heat, oil, and sharp
edges.
26. ELECTRICAL SHOCK. Never touch electrical wires or components while the engine is running. Exposed, frayed or
worn electrical wires and plugs can be sources of electrical shock which could cause severe injury or burns. Do not
touch the plug with wet hands. Prevent contact with grounded surfaces, for example pipes, radiators, ranges and
refrigerator enclosures.
27. WHEN TOOL IS USED OUTDOORS, only use extension cords intended for outdoor usage.
28. NEVER operate this equipment when not feeling well due to fatigue, illness or taking medicine.
29. NEVER operate this equipment under the influence of drugs, alcohol or any medication.
30. ALWAYS make sure that the machine is on level ground before using
31. ALWAYS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out
of the reach of children.
WARNING!
Sawing and drilling generates dust. Excessive airborne particles may cause irritation to eyes, skin and respiratory
tract. To avoid breathing impairment always employ dust controls and protection suitable to the material being
saw or drilled in accordance with OSHA (29 CFR Part 1910.1). Diamond blades improperly used are dangerous.
Comply with ANSI Safety Code B7.1 and OSHA covering speed, safety guards, flanges, mounting procedures,
general operating rules, handling, storage and general machine condition.
CALIFORNIA PROPOSITION 65 WARNING!
This product can expose you to chemicals including lead from lead-based paints, crystalline silica from bricks,
cement and other masonry products, and arsenic & chromium from chemically treated lumber, which are known
to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.

• 5 • diamondvantage.com
II. TS400: SYMBOLS
Keep guard in place
Diamond blade
III. TS400: TECHNICAL SPECIFICATIONS
TS400
MOTOR DIRECTION OF
SHAFT ROTATION
MAX. BLADE
CAPACITY
WEIGHT DIMENSIONS
2HP
115V~120V, 60Hz,
Single phase
Counter-
Clockwise
10” Blade
5/8” Arbor
68.5 lbs
Width: 24-1/64”
Length: 37-51/64”
Blade cutting depth
Electric switch off
Electric switch on
Electric hazard
Remove tools
Pay extreme attention
Repairs to be done
Machine hazard
Flammable
Read instructions carefully
Warning
Fragile
Keep dry
Do not step on
Wear hearing protection
Wear eye protection
Wear breathing protection
Wear hard hat
Wear protective clothing
Wear safety shoes
Well ventilated
No non-working personnel
Away from all moving parts Do not touch hot parts

• 6 • diamondvantage.com
IV. TS400: GETTING TO KNOW YOUR SAW
Motor Assembly
Blade Guard
Assembly
Splash Guard
Rail Platform
Assembly
Water Tray
Vertical Arm
Assembly
Power Switch
Diamond
Blade
Cutting Head
Adjustment
Handle
Main Table
Assembly

• 7 • diamondvantage.com
V. TS400: ACCESSORIES/PARTS
NAME (Qty.)
Miter Block (1)
Part Number
000101802-AG
NAME (Qty.)
Side Extension Table (1)
Part Number
475010803I-AG
NAME (Qty.)
45º/90º Edge Guide (1)
Part Number
000101702-AG
NAME (Qty.)
Drain Plug (1)
Part Number
488125002-AG
NAME (Qty.)
Allen Wrench (1)
Part Number
000101414
NAME (Qty.)
Wrench (2)
Part Number
000101423K
NAME (Qty.)
ABS Water Tray (1)
Part Number
480190203
NAME (Qty.)
Universal Saw Stand (1)
Part Number
563101000A-AG
The following are parts included in the package.

• 8 • diamondvantage.com
VI. TS400: BLADE INSTALLATION
1. Unplug the tile saw before installing a blade.
2. Carefully raise the cutting head to its highest
position and secure it into place by tightening the
cutting head adjustment knob located to the right
of the power switch at the front of the saw. Use
the provided Allen wrench when tightening the
cutting head adjustment knob.
3. Raise the blade guard to the highest position and
tighten the blade guard adjustment knob.
4. Remove the blade shaft nut and outer flange.
5. Place the blade onto the shaft making sure the
directional arrow on the blade is pointing
counter-clockwise.
6. After making sure that the blade is firmly placed
against the inner flange, secure it into place
with the outer flange and blade shaft nut. Make
certain the nut is firmly tightened with the wrench
provided, but do not over tighten!
7. Lower the blade guard and tighten the adjustment
knob with the provided Allen wrench.
8. Slightly loosen the cutting head adjustment knob
and lower the cutting head to its lowest position,
and then tighten the adjustment knob firmly to
hold the cutting head in place.
9. If blade needs to be removed, please use two
wrenches provided and follow the next steps:
a. Make sure to disconnect the saw from
electrical outlet.
b. Gently raise the blade guard to the
highest point.
c. Hold the saw shaft with one wrench
d. Hold the shaft nut with other wrench
e. Hold the wrench on the shaft and gently
untighten the nut using other wrench.
f. Remove the nut and outer flange and blade.
If nut is overtightened, DO NOT FORCE TO
UNTIGHTEN. Use a mallet to gently tab the top
of the wrench holding the nut to untighten.
Please use two wrenches when you remove the blade.
Figure 1
WARNING!
Place the blade to cut completely through the
material. Failing to do so may allow the saw to
grab the material being cut and cause it to shoot
out leading to severe injuries.

• 9 • diamondvantage.com
VII. TS400: SAFE OPERATING PRACTICES FOR TILE SAW
WARNING!
For your own safety and the safety of others, do
not attempt to operate this saw until you have
read and understood the general safety rules
for all power tools and the following additional
safety precautions particular to this saw.
5. Establish a training program for all operations of
this machine.
6. Always provide a copy of this manual to
equipment user.
7. Always select a diamond blade according to the
manufacturer’s recommendation suitable for the
material to be cut. Never use a blade having a
maximum operating speed lower than the “No
load R.P.M.” marked on the tool nameplate. Do
not operate any saw without safety guards in
place or with a blade diameter larger than the
maximum saw blade capacity.
8. Before mounting a blade on the saw, clean and
inspect the arbor shaft, blade flanges and the
diamond blade for uneven wear or damage. Do
not operate the tool if it appears to be damaged.
Have it serviced by a qualified technician.
9. Before each use of the saw, inspect the diamond
blade for hairline fatigue cracks. If such a crack
or flaw is evident, discard the blade. Using a
damaged diamond blade may cause injury to the
operator or others.
10. Be sure that the blade arbor hole matches the
blade adapter flange supplied with the saw. Use
only blade adapter flanges that came on your
saw. Never use damaged or worn blade adapter
flanges.
11. Install the blade with the arrow pointing in the
same direction as the rotation of the arbor shaft
or the arrow on the blade guard. Be sure to
tighten the blade shaft arbor nut with the wrench
provided but be careful not to over tighten.
WARNING!
Do not perform any operation freehand, that
is without holding the tile in place against the
fence and guide.
WARNING!
Never reach in back of cutting wheel.
WARNING!
Never cross arms in front of cutting wheel.
WARNING!
Keep hand out of path of cutting wheel.
WARNING!
The dust generated by cutting of tile, marble,
stone, bricks etc. can be harmful to your health.
Always operate machinery in well ventilated
areas and provide proper dust removal. Always
wear a dust mask approved for respiratory
protection against these types of dusts and mists.
1. Always wear approved hearing, eye, head and
respirator safety protection.
2. Read and understand the symbol definitions
contained in this manual.
3. Read and understand all warnings and
instructions on the machine.
4. Read all safety materials and instructions that
accompany any blade or accessory used with this
machine.

• 10 • diamondvantage.com
12. Check that the blade tracks near the center of the
channel in the main table, and that the table
moves freely from the front to back.
13. Sometimes the material being cut is not abrasive
enough to expose new diamonds on the blade.
If the blade is not sharpened, it will rub against
the surface of the material resulting in heat-
build in the core. To prevent this, it is necessary
to dress the blade. To dress the blade, simply
cut something abrasive like a piece of a cement
block. Indications that the blade needs dressing
include:
• The diamonds in the matrix appear shiny
because those are worn flat.
• The blade stops cutting or noticeably slows
down.
14. Before using the saw, fill the water tub with clean
water enough to submerge the water pump.
Replenish as necessary and clean the water tub
frequently. Do not operate a wet cutting blade
without adequate water flow to both sides of the
blade. Never run pump dry.
15. Never cut or grind with the side of the blade, only
cut in a straight line.
• Keep all parts of your body away from the blade
and all other moving parts.
• Never touch or try to stop a moving blade with
your hand.
16. Always unplug the water pump before cutting dry.
Never run the pump dry.
• Do not use a wet cutting blade for dry cutting.
Select the proper wet or dry cutting blade for
your application.
• To avoid a blade from heating up, allow the
blade to cool down by removing the tile and to
run freely for a few minutes.
17. Make sure all adjusting knobs are tight and
engaged in their detents and that movable
parts not intended to move during operation are
securely locked before making a cut. Be careful
not to over tighten.
18. Before connecting the machine to a power source,
check to see that the “On/Off” switch is in the
“off” position.
• Make sure the blade is not in contact with
anything before connecting the saw to a power
source and starting the motor.
• Know how to stop the machine quickly in case
of an emergency.
19. GROUNDING INSTRUCTIONS
Do not modify the plug provided. If it does not
fit the outlet, have a proper outlet installed by a
qualified electrician.
• In the event of a malfunction or breakdown,
grounding provides a path of least resistance
for electric current to reduce the risk of electric
shock. This tool is equipped with an electric cord
having an equipment-grounding conductor and
grounding plug. The plug must be plugged into
a matching outlet that is properly installed and
grounded in accordance with all local codes and
ordinances.
• Do not modify the plug provided - if it will not fit
the outlet, have the proper outlet installed by a
qualified electrician.
• Improper connection of the equipment grounding
conductor can result in a risk of electric shock.
• Check with a qualified electrician or service
personnel if the grounding instructions are
not completely understood, or if in doubt as to
whether the tool is properly grounded.
• Use only 3 wire extension cords that have 3 prong
grounding plugs and 3 pole electrical outlet that
accept the tool’s plug.
WARNING!
Not dressing the blade frequently or setting
the blade too high will cause it to grab the tile,
possibly causing injury to the operator and
damage to the saw.
IMPORTANT - If there is any tendency for the
saw to move during certain operations, such as
when cutting large heavy tiles, the saw must be
securely fastened to a supporting table.
VII. TS400: SAFE OPERATING PRACTICES FOR TILE SAW

• 11 • diamondvantage.com
Repair or replace damaged or worn cord immediately.
This tool is intended for use on a circuit with an outlet
as illustrated in Figure 2. The tool’s grounding plug is
illustrated in Figure 2(A). A temporary adapter (Figure
2(B) and 2(C) may be used to connect this plug to a 2
pole receptacle as shown in Figure 2(B) if a properly
grounded outlet is not available. The temporary adapter
should be used only until a properly grounded outlet can
be installed by a qualified electrician. The lug extending
from the adapter must be connected to permanent
ground such as a properly grounded outlet box.
Additionally, water pump requires the use of a Ground
Fault Circuit Interrupter. Therefore, when using the water
pump receptacle, this tool must be plugged into a properly
installed Ground Fault Circuit Interrupter outlet. See
Figure 2(D). If a Ground Fault Circuit Interrupter outlet is
not available, Diamond Vantage®has it available as an
accessory item. A plug-in Ground Fault Circuit Interrupter
may be plugged into a properly installed and grounded
3-pole outlet. Refer to Figure 2(E).
20. POSITION OF THE TILE SAW
• To avoid the possibility of the appliance plug
or electrical outlet getting wet, position the tile
saw to the side of the wall mounted outlet box to
prevent water from dripping onto it or the plug.
The user should arrange a “drip loop” in the cord
connecting the saw to the electrical outlet. Create
a “drip loop” by placing part of the cord below
the level of the electrical outlet, or the connector
if an extension cord is used. This will prevent
water from traveling along the cord and coming in
contact with the electrical outlet.
• Do not unplug the cord if the electrical outlet
gets wet. Disconnect the fuse or circuit breaker
that supplies power to the tool. Then unplug and
examine for presence of water in the electrical
outlet.
NOTE - Use of a Temporary Adapter is not permitted
in Canada.
Figure 2: GROUNDING METHODS
Grounding Pin
Cover of grounded
outlet box
Metal
Screw
Grounding
Means
(Lug)
Grounding Pin
(A) (B) (C) (D) (E)
To reduce the risk of electrocution, keep
all connections dry and off the ground. Do
not touch plug with wet hands.

• 12 • diamondvantage.com
IX. TS400: USING THE CUTTING TABLE
21. EXTENSION CORDS
• Only use extension cords that are intended for
outdoor use and marked “Acceptable for use with
outdoor appliances; store indoors while not in use.”
Only use extension cords with the electric rating
of the machine or above. Do not use damaged
or repaired extension cords. Examine extension
cords before using and replace if damaged. Do
not abuse extension cords and do not yank on any
cord to disconnect. Keep cords away from heat and
sharp edges. Always disconnect the extension cord
from the electrical outlet before disconnecting the
product from the extension cord.
FEATURES:
• Cutting table marked in inches for precision cuts.
• 14” cutting table provides more support during larger
cutting jobs than the standard 11” cutting tables.
USING 90º EDGE GUIDE:
1. Set the edge guide positioning it on the desired
dimension and tighten the threaded knob. Make
sure that the edge guide is firmly tightened to avoid
slippage. The edge guide can be used for 90º edge
cuts from both the left and right side.
2. 14” cutting table provides more support during larger
cutting jobs than the standard 11” cutting tables.
3. Simply line-up the material being cut with the
appropriate pre-marked lines on the cutting table
surface.
4. Now you are ready to make your cut.
MAKING MITER CUTS:
1. For miter cuts, place the lip of the miter block on the
measurement rail, with the threaded knobs facing you.
2. Tighten the threaded knobs to secure the provided miter
block in place.
3. Place material onto miter block and you are ready to cut.
• Ground Fault Circuit Interrupter (GFCI) protection
should be provided on the circuit(s) or outlet(s)
to be used for the tile saw. Electrical outlet with
built-in GFCI protection may be used for this
measure of safety.
VIII. TS400: SAFE OPERATING PRACTICES FOR TILE SAW

• 13 • diamondvantage.com
X. TS400: ELECTRICAL MOTOR SPECIFICATION
TS400
Horse Power 2 HP
Voltage 115V~120V
Amps 15 amps
Cycle 60 Hz
Phase 1
Class F
No Load Blade Shaft 3300 rpm
RECOMMENDATIONS:
• It is recommended that a minimum 15 amp circuit be used
while operating this saw. This will prevent possible power
interruption or loss.
• Always plug saw as close as possible to the power source
while operating. This will allow you to receive optimum
electricity.
TS400
LENGTH OF CORD
Wire
Gauge
2 HP
115V~120V
No. 12 25’
No. 10 50’
No. 8 75’
GreenGreen
Motor
Green
Green
Circuit
Breaker
Black Black Black
Black WhiteWhite
Switch
Black
Water
Pump
White
WARNING!
To avoid permanent motor damage, always use
the correct extension cord.

• 14 • diamondvantage.com
XI. TS400: TROUBLESHOOTING
WARNING!
For your safety and the safety of others, turn the power switch off and always remove the plug from the power
source before troubleshooting. Repairs performed by unauthorized personnel could cause serious hazard. We
recommend that service to this tool be performed by a qualified service technician with original equipment
replacement parts.
EXCESSIVE NOISE. If excessive noise is emanating from
the gearbox, have the tool serviced.
BLADE WILL NOT CUT. Check for worn out diamond edge.
Be sure that the arrow on the blade is rotating in the
same direction as the motor arbor and/or the arrow on
the blade guard. Make sure the blade is suitable for the
material to be cut. The blade might have become dull if
it has been used to cut a hard material. Dress the blade
by cutting a lightweight abrasive block to expose fresh
diamonds.
MOTOR WILL NOT START. Check power supply. If the
water pump turns on when the power switch is in the
“on” position, but the motor does not, have the motor
serviced.
MOTOR WILL NOT STOP. The contacts in the switch may
have become arched together in the “on” position – have
the tool serviced.
MOTOR SHUTS OFF DURING OPERATION. Check to see
that the circuit you are using is not overloaded with
lights or other equipment. The fuse or circuit breaker
may not have sufficient capacity – use 20-amp power.
If you are using an extension cord, check the extension
cord table to make sure it is heavy enough to carry the
current this product will draw. See Page 13 for electric
cord reference.
EXCESSIVE VIBRATION. Check to see that the blade is
mounted properly according to safe operating practices
section. Try a different blade as the blade might be out of
balance. The arbor shaft bearings might be worn and, in
that case, have the tool serviced.
NOT CUTTING SQUARE. Check the main table and
carriage adjustment as well as the blade alignment
procedure.
MAIN TABLE DOES NOT MOVE FREELY. Inspect the guide
rails and rollers for build up of tile chips or dry slurry
deposits. Clean and check guide roll or adjustments.
NO WATER FLOW TO BLADE. Check the water feed
tube for kinks or obstructions. Check the inlet screen
to ensure it is not clogged. Remove the pump inlet and
turn the impeller to ensure it is not damaged or jammed.
Clean the impeller if necessary and apply a drop of light
oil to the shaft - be sure the impeller spins freely.
POOR MACHINE PERFORMANCE WITH LITTLE POWER.
Check cord/extension cable for appropriate length and
gage. Check power network for sufficient power and
circuit breaker capacity.
CENTER HOLE IN BLADE OVERSIZE OR WORN. Saw blade
has slipped on shaft while running. Check shaft for
damage and replace blade.

• 15 • diamondvantage.com
XII. TS400: CUTTING DEPTH
The recommended cutting depth is 1/4” below the cutting table
surface. To adjust the cutting depth, loosen the cutting head
adjustment handle and set it to the lowest position, so that the blade is
1/4” below the top of the table surface.
BLADE DIAMETER MAX. CUTTING DEPTH
10 inch 2-1/4 inch
WARNING!
Place the blade to cut completely through the material. Failing to set up as instructed may result in the saw to grab
and shoot out the tile, causing severe injuries.
XII. WARRANTY
Diamond Vantage®warranties this product to be free from defects in material or workmanship for a period of either 6-month or 1-year
following the date of purchase. As long as the product has been used under normal working conditions, Diamond Vantage®will provide
replacement parts free of charge if motor, water pump or power switch fails within the first 6 months or any mechanical part, which
does not require electrical current to operate, fails within the first year. This warranty does not cover costs for labor or transportation in
connection with the replacement or repair of defective parts. Likewise, it does not apply to any unit which has been subjected to misuse,
neglect or accident, nor to any machine which has been repaired or altered by any person other than Diamond Vantage® authorized
personnel.
SERIAL NUMBER
ITEM CODE ITEM NAME
EQP-GF-0001010102 Y Connection 08f
EQP-GF-000103053 Water Pump
EQP-GF-33G108102B-AG Cutting Head Assembly F108
EQP-GF-381086009 8.5 x 14 x 0.2t Washer
EQP-GF-382019002 Countersunk Socket Hex Bolt 1/4 X 1 1/2
EQP-GF-452202003 Power Switch
EQP-GF-465903203-AG Roller Assembly
EQP-GF-471207003 Carbon Brush 7 X 17
EQP-GF-480190203 ABS Water Tray
EQP-GF-BEVFVX200265 R0151 Brush Motor

• 16 • diamondvantage.com
XIII. TS400: REPLACEMENT PARTS LIST - 1
Part Name Part No
1. Rail Platform Assembly 563210802A-AG
2. Table Assembly 675010804R-AG
3. Vertical Arm Assembly 5631108041B-AG
4. Cutting Head Assembly 33G108102B-AG
5. Blade Guard Assembly 373310802W-AG
6. Dia. 5/8” (15.88mm) Outer Flange 381166006
7. 10” x 5/8” (15.88mm) Diamond Blade 000102000
8. D30 x 120L Handle 373401801-AG
9. Spring 38112C025
11. Interlock Washer 565328008I
A. M8 x 16 x 1.5 Washer (qty.3) 3810860032
B. M8 Spring Washer 3810860012
Part Name Part No
12. Water Pump 000103053
13. M6 x 1.0 x 30L Socket Head Hex Bolt 3810690301
14. M8 x 22 x 2 Narrow Washer 381086012
15. Male 5/16 x 1” Knob 382059003
16. M8 x 1.25 Acorn Nut 3810800001
17. M8 Narrow Washer 381086101
18. M8 x 1.25 x 35L Cross Screw 3810810351
19. 5/8”-11 Hex Nut 3820500001
20. Dia. 5/8” (15.88mm) Inner Flange 381166005
21. Power Switch 452202003
MAIN ASSEMBLY
2
12
21
22
818 17
11
9
3
13
4
16
20 7
6
19
5
15
14
1
A
B

• 17 • diamondvantage.com
CUTTING HEAD ASSEMBLY
Part Name Part No
1. Cutting Head 33G108102B
2. Gear Cap 373206201
3. Blade Guard Shaft 70XZ017001I
4. Blade Shaft 70SS024002
5. Helical Gear 70HG682001
6. R0151 Brush Motor BEVFVX200265
7. Fan Cover 26E1440011
8. Spring Tension Plate 381166101I
9. Torsional Spring 38124C0261
10. Spring Spacer 565802101I
11. Spring Housing Cover 465514001B
12. 17mm x 7mm Carbon Brush (Set of 2) 471207003
13. Carbon Brush Cap (Set of 2) 471307002
14. D40 d24 Oil Seal 442440070
15. M5 x 0.8 x 25L Cross Screw 3810520253
Part Name Part No
16. M4 Narrow Washer 381046101
17. M4 Spring Washer 3810460041
18. M4 x 0.7 x 20L Cross Screw 3810420202
19. 5 x 5 x 12mm Woodruff Key 4642050541
20. M20 External C-Clip 474302000
21. M5 x 0.8 x 15L Cross Screw 3810520153
22. M4 x 0.7 x 10L Countersunk Cross Screw 381049010
23. M8 Spring Washer 3810860011
24. M8 x 1.25 x 20L Hex Bolt 3810810201
25. M10 x 1.5 Nut 3811000011
26. M10 Narrow Washer 381106261
27. D22 d8 608ZZ Radial Bearing 420608100
28. D47 d20 6204ZZ Radial Bearing 426204100
29. 13.5 x 32 x 2.3 Regular Washer 3811363211
E. 10 x 25 x 2 Washer 381106261
F. M5 x 8 Flat Head Set Screw 381058080
XIII. TS400: REPLACEMENT PARTS LIST - 2
16
17
18
7
15
19
61
21
2
4
14
28
5
27 20
F12
13
10
24
23
29
8
9
E
11 22
26
25
3

• 18 • diamondvantage.com
9
5
6
7
8
5
4
J
I
G
14
13
15
16
12
10 11
1
2
3
TABLE ASSEMBLY
Part Name Part No
1. Main Table 675010804F
2. Roller Mounting Plate 465722801
3. Nut Plate, Table 565716501
4. Upper Roller Spacer 565314003I
5. Water Shield 3810660061
6. Bypass Spacer 565801101I
7. Roller 465903201-AG
8. Lower Roller Spacer 565311003I
G. M6 Nylon Washer 381066101
H. 1/4 Nut 382010001
Part Name Part No
9. 1/4” - 20 x 1-1/4”L x 3/4” Hex Bolt 382011032
10. 1/4”- 20 x 1-1/4”L Flat Head Set Screw 3820180021
11. 1/4” - 20 Nut 382010001
12. 1/4” - 20 x 1 1/2 Countersunk Socket Hex Bolt 382019002
13. Adjustment Plate 465395001
14. 1/4 x 5/8 Sus Hex Socket Head Bolt 382019001
15. 1/4 x 20 UNC x 2” Flat Head Set Screw 3820180031
16. 1/4 Nut 382010001
I. 6 x 12 x 1 Washer 3810660074
J. M6 Spring Washer 3810660102
XIII. TS400: REPLACEMENT PARTS LIST - 3
H

• 19 • diamondvantage.com
BLADE GUARD ASSEMBLY
Part Name Part No
1. 10” Blade Guard 373310802W
2. Splash Guard 483514603
C. M6 x 15L Combination Screws 3810610153
D. 8 x 23 x 2 Washer 381086006
5. M4 x 0.7 x 20L Cross Screw 3810420202
6. 12cm Pipe 000101253
Part Name Part No
7. 120cm Pipe 000101255
8. 39cm Pipe 000101254
9. Y Connection 0001010102
10. M4 Narrow Washer 381046101
11. 1/4” Pipe 000101281
XIII. TS400: REPLACEMENT PARTS LIST - 4
2
C
D
5
10
7
11
6
1
9
8

• 20 • diamondvantage.com
RAIL PLATFORM ASSEMBLY
Part Name Part No
1. Rail Platform 563210801A
2. Front Platform Anchor 465624401A
3. Rear Platform Anchor 465624402A
4. Rail 574910802-1K
5. Skid Plate 565667601A
6. Rubber Feet 483505001
7. M5 x 0.8 x 10L Cross Screw 3810520102
8. Chain 4971R6033
K. M5 x 20 Cross Screw 3810520201
L. 6 x 19 x 2 Washer 3810660073
M. Roller Plate 465405201K
Part Name Part No
9. D21 Ring 38122C001I
10. D8 x 90L Quick Release Pin 38108A090K
11. 1/4” - 20 x 5/8”L Socket Head Hex Bolt 382019001
12. M5 Narrow Washer 381056102
13. M5 Spring Washer 3810560082
14. Combination Screw M6 x 10L 3810610103
15. Combination Screw M6 × 15L 3810610153
N. 6 x 12 x 1 Washer 3810660074
O. M5 Spring Washer 3810560082
P. M5 Nut 3810500002
XIII. TS400: REPLACEMENT PARTS LIST - 5
M
LK
PO
N
5
6
7
3
1
4
2
8
910
11
4
7
13
12 12
13
7
15
15
14
15
15
14