diBar 2D Series User manual
diBar™ 2D Series Quick start guide
www.dibar-corp.com
1
Please this manual thoroughly prior to ensure full use of the product’s functionality and
sore safety in a convenient location for quick reference even after reading.
SAFETY PRECAUTIONS
Meaning of symbols
WARNING
Alters you to those conditions which could cause serious bodily
injury or death if the instructions are not followed correctly.
CAUTION
Alters you to those conditions which could cause minor bodily injury
or substantial property damage if the instructions are not followed
correctly.
Be sure to observe all these safety precautions.
WARNING
Never disassemble or modify the device; doing so could result in an accident and such as fire or malfunction.
Never put the device into a microwave oven or high pressure container.
If smoke, abnormal odors or noises come from the device, immediately unplug the
power from the device.
Failure to do so could cause fire or electrical shock.
Never use the device on the line voltage other than the specified level. Doing so could cause the device
to break or burn.
Do not scratch, modify, bend, twist, pull or heat the AC adapter cable.
Do not place heavy material on
the cable or allow the cable to get pressed under heavy material. Doing so could break cable, resulting
in a fire.
If the power
cord of the AC adapter is damaged, stop using it and contact your nearest dealer. Failure
to do so could result in a fire or electric shock.
Do not plug in or unplug the power cord with wet hands.
If the device shows signs of abnormality, immediately unplug the AC adapter or interface cable from the
device.
If foreign material or water gets into the device, immediately unplug the AC
adapter or interface cable
from the device. Failure to do so could result in a fire or electric shock.
If you drop the device so as to damage its housing, immediately unplug the AC adapter or interface cable
from the device. Failure to do so could result in a fire or electric shock.
Use the recommended AC adapter only. Failure to do so could result in a fire.
For rechargeable battery, charger, and charging process
Never use a rechargeable battery other than that specified in the device user guide.
Never charge a dry cell battery or a recharge battery other than that specified in the device user guide.
Doing so could cause heat generation, breakage, or fluid leakage.
Do not touch directly charge terminals and battery with wet hands.
CAUTION
Never put the device in places where there are exclusively high temperatures such as inside closed-
up
automobiles or in places exposed to direct sunlight. Doing so could affect the housing or parts, resulting
in a fire.
Avoid using the device in extremely humid or dusty areas or where there are drastic temperature changes.
Moisture or dust will get into the device, resulting in malfunction, fire or electric shock.
Never cover or wrap up the device or AC adapter in a cloth or blanket. Doing so coul
d cause the device
to heat up inside, deforming its housing, resulting in a fire.
Always use the device and AC adapter in a well-ventilated area.
Do not place the device anyplace where it may be subjected to oily smoke or steam, e.g., near a cooking
range or humidifier. Doing so could cause result in a fire or electric shock.
Keep the power cord away from any heating equipment
. Failure to do so could melt the sheathing, result
in a fire or electric shock.
Do not insert or drop foreign materials such as metals or anything inflammable
through the openings or
vents into the device. Doing so could cause result in a fire or electric shock.
For safety reason, unplug the AC adapter and disconnect interface cable when not using for long periods
of time.
Regulations
The device complies with FCC Class B, CE Class B and RoHS.
1. Due to continued product development this information may change without notice.
2. All brand, product and service, and trademark names are the property of their registered
owners.
Copyright © 2016 WELCOM DESIGN KK., All rights reserved
diBar™ 2D Series Quick start guide
www.dibar-corp.com
2
Thanks for using diBar brand 2D reader(Call as just reader from now on in
this guide).
Manual/Driver/Utility software
Please visit our WEB site below to get necessary documents and software.
http://dibar-corp.com/en/
Contents of reader package
Please check your package. If you find missing or broken materials, please contact to your
dealer.
Reader with specified I/F cable 1pc
(*) If you purchase accessories, you can find them such AC adapter, Holder, Stand.
Please keep the package box to send back the reader for repairing to prevent damage during
transportation.
Shapes and name of parts
Good read LED
Reading window
Trigger key
Good read LED
Trigger key
Reading window
Hollow which indicates
trigger position
Out your thumb here, then you
can find
trigger position
easily.
diBar™ 2D Series Quick start guide
www.dibar-corp.com
3
RS232C interface connection
Please refer to figure below and connect your reader to PC properly.
Note; please use only recommended AC adapter.
USB interface connection
Please refer to figure below and connect your reader to PC properly.
How to read a code
Reader adopts red LED aimer. In case of reading code, operator must put the red aimer on
center of target code, see figures below. Since reader is able to read any direction of
code, operator doesn’t need to care about it.
1
次元ｺｰﾄﾞ
ﾏﾄﾘｸｽｺｰﾄﾞ
123456
123456
diBar™ 2D Series Quick start guide
www.dibar-corp.com
4
Reset to factory default
Read command barcode below. Reader resets all parameter to factory defaults.
RS232C Interface
Read command barcode below. Reader adopts RS232 interface with its default settings.
Here are default parameters of RS232 interface.
Parameter
Setting value
Baud rate
115,200bps
Data format
8 data bits, None parity, 1 stop bit
Suffix
CR/LF
Trigger mode
Manual trigger
If you want to set baud rate to 9600bps, read command barcode below.
USB keyboard interface(USA)
Read command barcode below. Reader adopts USB keyboard interface(USA).
Keyboard country layout
Read command barcode below to set appropriate keyboard layout for your country.
Here showed major country layouts, but you can find other layouts in user guide which is
able to download from our WEB site.
USA
Belgium
Brazil
Dutch
Denmark
France
Germany
Greek
Italy
Poland
~ D E F A L T .
~ P AP232.
~ 2 3 2 B A D 5 .
~P A P 1 2 4 .
~ K B D C T Y 0 .
~ K B D C T Y 1 .
~ K B D C T Y 1 6 .
~ K B D C T Y 1 1 .
~ K B D C T Y 8 .
~ K B D C T Y 3 .
~ K B D C T Y 4 .
~ K B D C T Y 1 7 .
~ K B D C T Y 5 .
~ K B D C T Y 2 0 .
diBar™ 2D Series Quick start guide
www.dibar-corp.com
5
USB HID-POS interface
Read command barcode below. Reader adopts USB HID-POS interface.
USB serial port emulation(USB-COM)
Read command barcode below. Reader adopts USB serial port emulation(USB-COM) interface.
In this interface mode, you need to install its driver. The driver is able to download
from our WEB site.
As for the MAC, since MAC will recognize reader as CDC class device, driver will be installed
automatically.
You can select ACK/NAK handshake option below.
｢
ACK/NAK handshake enable
｣
｢
ACK/NAK handshake disable
｣
｢Note｣
There is no baud rate option for USB serial port emulation interface.
Suffix Enter
Read command barcode below. Reader adopts Enter as suffix for all symbologies.
Suffix Enter(All symbologies)
(*) In case of RS232C/USB serial port emulation interface, reader uses CR(0Dhex) as suffix.
~PAP 1 31 .
~T E R M I D 1 3 0 .
~ P A P 1 2 4 .
~ P A P 1 2 5 .
~ V S U F C R .
diBar™ 2D Series Quick start guide
www.dibar-corp.com
6
Sample code
Code 39
JAN-13
PDF417
Data Matrix
QR(MODEL 2)
Negative QR(MODEL 2)
* C O D E 3 O F 9 *
3456789012340
PDF417 Sample
DataMatrix
QR CODE MODEL 2
QRNega
Table of contents
