digi-tech HYPERPHASE User manual

Warning
For your protection, please read the following:
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Do not use this apparatus near water.
5. Clean only with dry cloth.
6. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
7. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
8. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
9. Unplug this apparatus during lightning storms or when
unused for long periods of time.
10. No user serviceable parts inside. Refer all servicing to
qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
11.WARNING:To reduce the risk of fire or electric
shock, do not expose this apparatus to rain or
moisture.
12. Refer to labels on the unit, including bottom cover, or
other markings and pertinent information.
DECLARATION OF CONFORMITY
Manufacturer’s Name: DigiTech
Manufacturer’s Address: 8760 S. Sandy Parkway
Sandy, Utah 84070, USA
declares that the product:
Product name: Hyper Phase
Product option: all (requires Class II power
adapter that conforms to the
requirements of EN60065,
EN60742, or equivalent.)
conforms to the following Product Specifications:
Safety: IEC 60065 (1998)
EMC: EN 55013 (1990)
EN 55020 (1991)
Supplementary Information:
The product herewith complies with the requirements of the
Low Voltage Directive 72/23/EEC and the EMC Directive
89/336/EEC as amended by Directive 93/68/EEC.
Vice-President of Engineering
8760 S. Sandy Parkway
Sandy, Utah 84070, USA
Date: May 30, 2002
European Contact: Your local DigiTech Sales and
Service Office or
Harman Music Group
8760 South Sandy Parkway
Sandy, Utah
84070 USA
Ph: [phone]
Fax: [phone]

WARRANTY: We at DigiTech are proud of our products and back-up each one with the following warranty:
1.The warranty registration card must be mailed within ten days after purchase date to validate this war-
ranty.
2. DigiTech warrants this product, when used solely within the U.S., to be free from defects in materials
and workmanship under normal use and service.
3. DigiTech liability under this warranty is limited to repairing or replacing defective materials that show
evidence of defect, provided the product is returned to DigiTech WITH RETURN AUTHORIZATION,
where all parts and labor will be covered up to a period of one year (this warranty is extended to a
period of six years when the product has been properly registered by mail or through our website).
A Return Authorization number may be obtained from DigiTech by telephone.The company shall not
be liable for any consequential damage as a result of the product's use in any circuit or assembly.
4. Proof-of-purchase is considered to be the burden of the consumer.
5. DigiTech reserves the right to make changes in design, or make additions to, or improvements upon
this product without incurring any obligation to install the same on products previously manufactured.
6.The consumer forfeits the benefits of this warranty if the product's main assembly is opened and tam-
pered with by anyone other than a certified DigiTech technician or, if the product is used with AC volt-
ages outside of the range suggested by the manufacturer.
7.The foregoing is in lieu of all other warranties, expressed or implied, and DigiTech neither assumes nor
authorizes any person to assume any obligation or liability in connection with the sale of this product.
In no event shall DigiTech or its dealers be liable for special or consequential damages or from any
delay in the performance of this warranty due to causes beyond their control.
NOTE:The information contained in this manual is subject to change at any time without notification. Some
information contained in this manual may also be inaccurate due to undocumented changes in the product or
operating system since this version of the manual was completed.The information contained in this version
of the owner's manual supersedes all previous versions.

The Hyper Phase is a multi-function phaser pedal that offers seven
different types of phasing effects and CIT™ cabinet modeling. The
following sections outline how the knobs and pedal functions work.
1. Speed Knob
Controls the speed of the phase shift sweep. Turn this knob clockwise
to increase the speed, and counter-clockwise to decrease the speed.
2. Depth Knob
Controls the depth of the phase shift effect. Turn this knob clockwise to
increase the depth, and counter-clockwise to decrease the depth.
3.AC Adapter Jack
Connect a DigiTech PS200R (9VDC output) power supply to this jack.
Use the proper supply for your area’s Mains line voltage.
4. Regen Knob
Controls the amount of regeneration (feedback) in the phaser effect.
Turn this knob clockwise to increase the regeneration, and counter-
clockwise to decrease the regeneration. When
4-RISE/FALL is selected,
this knob creates a rising sweep when set between the minimum and 12
o’clock positions, and a falling sweep when set between the 12 o’clock
and maximum positions.

1
5
2 3 4
6
9
10
11
7
8

5.Type Knob
Selects 1 of the 7 different phaser effect types.
1-STAGE A - A 4 stage phase shifter.
2-STAGE B - An 8 stage phase shifter.
3-STAGE C - A 12 stage phase shifter.
4-RISE / FALL - Creates a constant rising phaser sound when the
REGEN knob is set between the minimum and 12 o’clock positions,
or a constant falling phaser sound when the
REGEN knob is set
between the 12 o’clock and maximum positions.
5-TRIG UP* - The phaser effect starts at the bottom of its sweep
when the trigger threshold is reached. Use the
REGEN knob to
adjust the trigger threshold sensitivity and
SPEED knob to adjust
sweep rate. Regeneration is fixed when Triggered Up is selected.
6-TRIG DOWN* - The phaser effect starts at the top of its sweep
when the trigger threshold is reached. Use the
REGEN knob to
adjust the trigger threshold sensitivity and
SPEED knob to adjust
sweep rate. Regeneration is fixed when Triggered Down is selected.
7-STEP - Creates a random square wave phase effect similar to a
sample and hold filter on a synthesizer.
* Using a distortion pedal before the Hyper Phase may cause
inconsistent triggering due to the non-dynamic nature of distorted
signals.

6. Input Jack
Connect your instrument to this jack. Connecting a guitar cable to this
jack supplies battery power even though the Indicator LED may not be
lit. To prolong battery life, disconnect all cables from the pedal when not
in use.
7. Pedal Release Pins
These two pins are spring-loaded hinges that hold the pedal in place.
Push these pins in to release the pedal from the pedal chassis exposing
the battery compartment. (See battery replacement diagram).
8. Pedal
Press the pedal to turn the effect on and off.
9. Out 1(Mono) Jack
Connect this output to a single guitar amplifier or mixer channel when
only one amp or mixer channel is being used.
10. Indicator LED
This LED indicates when the effect is turned on. If the LED becomes
dim or does not light when the cables are connected, the battery needs
to be replaced.

11. Out 2 Jack
Connect this output to a second amplifier or mixer channel for stereo
phasing. Stereo is the best way to get the most effective stereo phaser
experience from the Hyper Phase pedal.
Connections
The Hyper Phase has a single input and a pair of outputs. Out 1 is used
if the Hyper Phase is being connected to only one amplifier or mixer
channel panned center. Out 2 is used for stereo operation. Connect
Out 1 to the first amplifier or mixer channel panned left and Out 2 to
the second amplifier or mixer channel panned right.
The Hyper Phase also has built-in CIT™ cabinet modeling that can be
enabled. This is a useful tool when running a distortion pedal into the
Hyper Phase and then running direct into a mixer or recorder. CIT
creates a guitar-through-an-amplifier sound without having to use a
guitar amp.
To Enable CIT™ Cabinet Modeling:
Press the pedal down and apply power (connect a guitar cable to the
Hyper Phase input or connect the PS200R power supply to the AC
adapter jack). CIT™ cabinet modeling has to be turned on each time
you apply power to the Hyper Phase.

Battery Replacement
1. Using the tip of a 1/4” guitar cable, push one of the release pins in on
either side of the pedal, and remove the pedal from the pedal chassis.
2. Remove the battery from the battery compartment and disconnect
the battery cable.
3. Connect a new battery to the battery cable and put it back in the
battery compartment. Make sure the battery cable does not interfere
with the spring or pedal switch arm.
4. Place one hole of the pedal over its corresponding pin.
5. Push the opposite pin in and lower the other side of the pedal into
place over the depressed pin. Release the pin. When the pedal is
properly fastened, both release pins are flush with the outer side of
the pedal.

9V DC Battery
Pedal Release
Pin
Pedal Chassis
Pedal
Pedal Switch
Arm
Pedal Release
Pin
Battery
Compartment
Spring

DigiTech
8760 South Sandy Parkway
Sandy, Utah 84070
PH [phone]
FAX [phone]
DigiTech and X-Series are trademarks
of the Harman Music Group Inc.
Copyright - Harman Music Group
Hyper Phase Stereo Phaser
Owners Manual 18-1806V-A
Please visit DigiTech
on the World Wide Web at:
www.digitech.com
Printed in China
SPECIFICATIONS:
• Controls - Speed, Depth, Regen,Type,
On/Off Pedal
• Jacks - Input, Out 1 (Mono), Out 2
• Input Impedance - 1 MOhms
• Output Impedance - 100 Ohms
• Power Supply - 9V Alkaline Dry Battery
• Power Consumption - 4.8Watts
(w/optional PS200R power supply)
• Battery Life - Approximately 4 hours
(with continuous usage)
• Dimensions - 4 15/16”(L) x 3 1/8”(W)
x 2 1/8”(H)
• Weight - 1.38 lbs.
• Optional Power Supply
PS200R - 100 (100V ~ 50/60Hz)
PS200R - 120 (120V ~ 60Hz)
PS200R - 230 (230V ~ 50Hz)
PS200R - 240 (240V ~ 50Hz)