Digitalview Hd-3000v2 User manual

Specifications subject to change without notice

HD/SD-SDI to HDMI adaptor board

HD-3000v2

Manual

Specifications subject to change without notice

Table of Contents

1. Introduction

3

2. Connectors, Pin outs & Jumpers

5

3. LED status and Source switching

9

4. Board Dimensions

10

5. Signal Support Mode Table

11

6. Specification

12

7. Appendix I - RS-232 control protocols

13

8. Appendix II - System Connection with

Digital View LCD controllers

14

9. Warranty, Caution & Limitation of Liability, Trademarks

15

10. Contact details

16

11. Revision History

17

1. Introduction

Specifications subject to change without notice

The HD-3000v2 provides a SD/HD-SDI signal front end to Digital View LCD controller boards.

HD-3000v2 Key Features

a. Converts SD/HD-SDI (SD, HD and 3G) video input to HDMI output, up to Full-HD resolution.

b. Re-clocked loop through outputs for “daisy chaining” multiple monitors or other equipment to the same HD-SDI source, includes

embedded audio.

c. Fully compliant with the SMPTE 259M-C, SMPTE 292M, SMPTE 424M, 425M standards.

d. Supports 1.5Gbits & 3Gbits bit rate input signal support. The mode support is listed in page 10.

e. Two SDI input port switching with One HDMI out supported.

HD-3000v2 supports Path A (HD-SDI input from J1 port convert to output HDMI at HDMI1/HDMI1A port) or Path B (HD-SDI input

from J2 port convert to output HDMI at HDMI1/HDMI1A port). See Figure below :

f. HD-SDI re-clock loop through output. J1 HD-SDI input and re-clock loop through to J3 HD-SDI output. J2 HD-SDI input and re-clock

loop through to J4 HD-SDI output.

g. HDMI (v1.3) x 1 output port. One HDMI output ports are HDMI1/HDMI1A outputting 1920x1080p60 mode.

h. Stereo embedded audio support .

i. Input interlaced SDI video is de-interlaced to HDMI output for non-frame buffered DV controller.

g. Provide fast input port switching between the dual SDI inputs if the two SDI inputs are in the same video format. (HDMI output is

always ON).

h. PIP support option (custom firmware required).

Specifications subject to change without notice

2. CONNECTORS, PINOUTS & JUMPERS

The various connectors are:

Summary: Connectors

Ref

Description

Type / Use

J1

SD/HD-SDI 1 Input

BNC connector

J2

SD/HD-SDI 2 Input

BNC connector

J3

SD/HD-SDI 1 re-clock loop through output

BNC connector

J4

SD/HD-SDI 2 re-clock loop through output

BNC connector

CN1

RS-232 & I2C control connector

JST 6-way, B6B-XH-A or compatible (Matching type : XHP-6)

> (Matching power & I2C cable P/N 426090700-3 for connection

with Digital View LCD controller)

> (Matching cable with DB9 female connector P/N 426090200-3

for RS-232 command communication)

> (Matching cable with DB9 male connector P/N 426090400-3 for

RS-232 command communication)

CN4

External I/O connector

Hirose DF13-8P-1.25DSA or compatible.

(Matching type : Hirose DF13-8S-1.25C)

(Matching extend cable with Hirose DF13-8S-1.25C

connector : P/N 426894500-3)

HDMI1

HDMI 1 Output

HDMI connector

Specifications subject to change without notice

Ref

Description

Type / Use

HDMI1A

Alternate HDMI 1 Output

JST BM20B-SRDS (Matching type : JST SHDR-20V-S-B)

(Matching extend cable with female HDMI connector :

P/N 426301800-3)

(Matching extend cable with male HDMI connector :

P/N 426006600-3)

PP1

Power Input (Alternate)

Molex 43650-0200 compatible

(Matching connector type : Molex 43645-0200 compatible)

(Matching power cable : P/N 426013800-3)

SW2

Manual SDI 1 / SDI 2 Input port selection

(work for standalone application only)

Tact Switch

Summary: Jumper settings :

Ref

Purpose

Note

LED1A

External LED connection

Refer to pin assignment in page 7

LED2A

External LED connection

Refer to pin assignment in page 7

LED3A

External LED connection

Refer to pin assignment in page 7

JP1

Reserved for programming use

Reserved

Specifications subject to change without notice

Summary : PinOuts :

CN1 – RS-232 & I2C control : JST B6B-XH-A (Matching type : XHP-6)

SYMBOL

DESCRIPTION

1

SCLK

I2C_SCLK

2

SDATA

I2C_SDATA

3

VCC

+5V (optional input power)

4

TXD

RS-232 Tx data

5

GND

Ground

6

RXD

RS-232 Rx data

CN4 – External I/O connector : Hirose DF13-8P-1.25DSA (Matching type : Hirose DF13-8S-1.25C)

SYMBOL

DESCRIPTION

1

3V3

3.3V output

2

LED3

LED3 Anode

3

N/A

4

N/A

5

EXT_IP_1

Reserved

6

LED1

LED1 Anode

7

LED2

LED2 Anode

8

GND

LED Cathode

LED1A, LED2A, LED3A – External LED connection

SYMBOL

DESCRIPTION

1

+

LED Anode

2

-

LED Cathode

HDMI1A – Alternate HDMI connector: JST BM20B-SRDS (Matching type : JST SHDR-20V-S-B)

SYMBOL

DESCRIPTION

1

GND

Ground

2

GND

Ground

3

RXC+

TMDS Data C+

4

RXC-

TMDS Data C-

5

RX0+

TMDS Data 0+

Specifications subject to change without notice

SYMBOL

DESCRIPTION

6

RX0-

TMDS Data 0-

7

RX1+

TMDS Data 1+

8

RX1-

TMDS Data 1-

9

RX2+

TMDS Data 2+

10

RX2-

TMDS Data 2-

11

GND

Ground

12

GND

Ground

13

MSTR2_SCL

Reserved

14

MSTR2_SDA

Reserved

15

DDC_5V

+5V power supply for DDC (optional)

16

HPD

Hot plug detection

17

DDC_SCL

DDC serial clock

18

DDC_SDA

DDC Data

19

VCC1

VCC 5V output

20

VCC2

VCC 5V output

PP1 - 12VDC power supply

DESCRIPTION

1

+12VDC in

2

Ground

Specifications subject to change without notice

3. LED status and Source switching

Status LEDs on board, definition: LED1, LED2, LED3

Ref

Description

LED1 / LED2

Green LED on: Signal detected

LED3

Green LED on: Power on and HDMI output

Source switching:

The two SDI inputs can be selected by:

a) On board tact switch to toggle from one SDI input to another one SDI input:

* Tact switch functionality will be disabled when connected with a Digital View LCD controller as in (c) below.

b) RS-232 commands (Refer to Appendix I)

c) Connect with Digital View LCD controller (Refer to Appendix II)

The last selected SDI input source will be memorized after power cycle.

Specifications subject to change without notice

4. BOARD DIMENSIONS

Ready-made 3D Pro-E (SLDPRT) drawing files - Save time and effort for your system volumetric analysis design.

Includes jpg file previews. Please go to download at http://www.digitalview.com/accessories/hd-3000v2

The maximum thickness of the adaptor board is 18mm (measured from bottom of PCB to top of components, excluding the

BNC connectors. We recommend clearances of:

• 5mm from bottom of PCB - if mounting on a metal plate we also recommend a layer of suitable insulation material is

added to the mounting plate surface.

• 10mm above the components

• 3~5mm around the edges

Any of the holes shown above can be used for mounting the PCB, they are 3.2mm in diameter.

CAUTION: Ensure adequate insulation is provided for all areas of the PCB with special attention to high voltage parts

such as the inverter.

Specifications subject to change without notice

5. SIGNAL SUPPORT MODE TABLE

HDMI output mode

1920x1080p60

(for input fast port switching)

SDI input Mode

576i50 (PAL)

480i60 (NTSC)

720p60 (4:2:2)

720p59.94 (4:2:2)

720p50 (4:2:2)

720p30 (4:2:2)

720p29.97 (4:2:2)

720p25 (4:2:2)

720p24 (4:2:2)

720p23.98 (4:2:2)

1080p30 (4:2:2)

1080p29.97 (4:2:2)

1080p25 (4:2:2)

1080p24 (4:2:2)

1080p23.98 (4:2:2)

1080psf30 (4:2:2)

1080psf25 (4:2:2)

1080psf24 (4:2:2)

1080psf23.98 (4:2:2)

1080i60 (4:2:2)

1080i59.94 (4:2:2)

1080i50 (4:2:2)

1080p60 (4:2:2)

1080p50 (4:2:2)

Specifications subject to change without notice

6. Specification

Supported serial interface standard

SMPTE 292M, 259M-C, 424M, 425M (Level A)

Supported SDI video mode

576i50 (PAL)

480i60 (NTSC)

720p60 (4:2:2)

720p59.94 (4:2:2)

720p50 (4:2:2)

720p30 (4:2:2)

720p29.97 (4:2:2)

720p25 (4:2:2)

720p24 (4:2:2)

720p23.98 (4:2:2)

1080p30 (4:2:2)

1080p29.97 (4:2:2)

1080p25 (4:2:2)

1080p24 (4:2:2)

1080p23.98 (4:2:2)

1080psf30 (4:2:2)

1080psf25 (4:2:2)

1080psf24 (4:2:2)

1080psf23.98 (4:2:2)

1080i60 (4:2:2)

1080i59.94 (4:2:2)

1080i50 (4:2:2)

1080p60 (4:2:2)

1080p50 (4:2:2)

Number of channel input port supported

2

HD-SDI re-clock loop through output

Yes

Output port

HDMI (v1.3) x 1

Embedded audio

Supported with Stereo

LEDs

Status LED (Green)

Power requirement

Regulated DC 12V input (2.5mm center positive)

(optional +5V , <1.3A input via CN1)

Power consumption

+12VDC ±5%, 5W

(optional +5VDC ±10%, 5.5W )

Environmental

Operating temperature : 0oC to 60oC

Relative humidity : 5%-95% relative humidity

(Non-condensing)

RoHS Compliant

Yes

Dimensions

102(W) x 77.6 (D) x 18(H) mm

Specifications subject to change without notice

7. Appendix I - RS-232 control protocols

RS-232 Serial control (Baud rate 9600, 8 bits, 1 stop bit and no parity)

Physical connection :

Controller side Computer side

Connector interface : CN1 Connector interface : Serial port

Mating connector : Molex 51021-0600 Mating connector : DB9 Female

PIN#

Description

PIN#

Description

4

RS-232 Tx Data

2

RS-232 Rx Data

5

Ground

3

RS-232 Tx Data

6

RS-232 Rx Data

5

Ground

Input port

select

0x98,

nn | “+” |

“-” |

“r” | “R” |

“?”

Select input main =

SDI 1 or SDI 2 or

next available

Reset

Query

Main selected.

“0x45,0x31” SDI 1(Default)

“0x45,0x32” SDI 2

5 4

631

54

6

3

1

789

Mating face of RS-232 DB9 Male

Mating face of CN8

Specifications subject to change without notice

8. Appendix II - System connection with Digital View

LCD controllers.

HD-3000v2 with SVX-1920-PRO (as an example) :

HD-3000v2 with SP-1920v2 (as an example) :

Remark :

* Custom firmware version required.

Please note that the overall suitability and image quality acceptance for usage in critical applications must be independently tested

and verified by the user.

Specifications subject to change without notice

9. WARRANTY

The products are warranted against defects in workmanship and material for a period of three (3) year from the date of purchase

provided no modifications are made to it and it is operated under normal conditions and in compliance with the instruction manual.

The warranty does not apply to:

• Product that has been installed incorrectly, this specifically includes but is not limited to cases where electrical short circuit is

caused.

• Product that has been altered or repaired except by the manufacturer (or with the manufacturer’s consent).

• Product that has subjected to misuse, accidents, abuse, negligence or unusual stress whether physical or electrical.

• Ordinary wear and tear.

Except for the above express warranties, the manufacturer disclaims all warranties on products furnished hereunder, including all

implied warranties of merchantability and fitness for a particular application or purpose. The stated express warranties are in lieu of

all obligations or liabilities on the part of the manufacturer for damages, including but not limited to special, indirect consequential

damages arising out of or in connection with the use of or performance of the products.

CAUTION

Whilst care has been taken to provide as much detail as possible for use of this product it cannot be relied upon as an

exhaustive source of information. This product is for use by suitably qualified persons who understand the nature of the

work they are doing and are able to take suitable precautions and design and produce a product that is safe and meets

regulatory requirements.

LIMITATION OF LIABILITY

The manufacturer’s liability for damages to customer or others resulting from the use of any product supplied hereunder shall in no

event exceed the purchase price of said product.

TRADEMARKS

The following are trademarks of Digital View Ltd:

• Digital View

• HD-3000v2

Specifications subject to change without notice

10. CONTACT DETAILS

Digital View has offices in Asia, Europe and USA :

USA

Digital View Inc.

18440 Technology Drive

Building 130

Morgan Hill,

California, 95037

USA

Tel: (1) 408-782 7773 Fax: (1) 408-782 7883

Sales: [email protected]

EUROPE

Digital View Ltd.

6 Marylebone Passage,

London, W1W 8EX,

UK.

Tel: +44-(0)20-7631-2150 Fax: Fax: +44-(0)20-7631-2156

Sales: [email protected]

ASIA

Digital View Ltd

Unit 705-708, 7/F Texwood Plaza

6 How Ming Street

Kwun Tong, Hong Kong

Tel: (852) 2861 3615 Fax: (852) 2520 2987

Sales: [email protected]

WEBSITE

www.digitalview.com

Specifications subject to change without notice

11. REVISION HISTORY

Date

Rev No.

Page

Summary

23 Feb 2023

1.00

All

First Issue version.

digitalview HD-3000v2 User manual

Popular Computer Hardware manuals by other brands