digitalview IE-1000 User manual

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.4: 26 March, 2009 (IE-1000 -2X manual.doc) Page 1 of 19
IMAGE ENHANCER ADD-ON BOARD
FOR 120Hz PANEL
Model: IE-1000
Part number : 417190021-3 or up
[Firmware version : V1.80.00]
INSTRUCTIONS
CONTENTS
Page: 2. Introduction, How to Proceed, Usage Note, Disclaimer
3. System design – Diagram of a suggested system
4. Assembly notes – Important information about system elements
6. Connection & Operation – How to use the IE-1000
8. Connectors, pinouts & jumpers – Essential connection information
13. Board dimensions
14. Troubleshooting
15. Specifications
16 Appendix I – Mapping definition
18. Warranty, Caution & Limitation of Liability, Trademarks
19. Contact details
It is essential that these instructions are read and understood before connecting or
powering up the IE-1000

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.4: 26 March, 2009 (IE-1000 -2X manual.doc) Page 2 of 19
Introduction
The IE-1000 is a Digital View add-on board providing:
•10 bit panel support and 120Hz panel support with motion compensation frame interpolation
for smoother motion
The IE-1000 can currently be matched with the Digital View SVH-1920 and upcoming SVX-1920
controllers to provide support for:
•Displays up to 1920x1200, 10 bit, 120Hz.
HOW TO PROCEED
•As most panels require different connection settings and cables it is important to have the
relevant Digital View Connection Diagram before assembly begins. This is obtainable from
the Digital View website as follows:
•Ensure all parts are on hand.
•Check controller and add-on board switch & jumper settings (errors may damage the panel)
•Prepare the source
•Connect the parts
•Understand the operation & functions
IMPORTANT USAGE NOTE
This equipment is for use by system manufacturers, developers and qualified integrators, the
manufacturer accepts no liability for damage or injury caused by the use of this product. It is
the responsibility of the developer, integrators or other user of this product to:
•Ensure that all necessary and appropriate safety measures are taken.
•Obtain suitable regulatory approvals as may be required.
•Check power settings to all component parts before connection.
DISCLAIMER
There is no implied or expressed warranty regarding this material.
Controller Solution Generator
A web based resource matching controllers & panels with connection diagrams
for download. Visit : http://www.digitalview.com/controllers/csg.php

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.4: 26 March, 2009 (IE-1000 -2X manual.doc) Page 3 of 19
SYSTEM DESIGN
A typical LCD based display system utilizing the IE-1000 is likely to comprise the following:
Summary:
1. LCD panel
2. Image Enhancer board, IE-1000
3. LCD controller card
4. Interconnect LVDS cable (P/N 426497600-3, 200mm)
5. Panel power cable (if required)
6. Panel cable for LVDS panel
7. RS-232 interface (for firmware upgrade only)
8. +12V / +24V DC power input
9. Power and inverter control cable
Digital View provides a range of parts, such as listed above, to make up complete display solutions.

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.4: 26 March, 2009 (IE-1000 -2X manual.doc) Page 4 of 19
ASSEMBLY NOTES
The IE-1000 is designed for monitor and custom display projects using 1920x1200 or 1920x1080
resolution 10 bit 120Hz TFT panels with connection with compatible Digital View controllers. The
following provides some guidelines for installation and preparation of a finished display solution.
Preparation: Before proceeding it is important to familiarize yourself with the parts making up the
system and the various connectors, mounting holes and general layout of the IE-1000. As much as
possible connectors have been labeled. Guides to connectors and mounting holes are shown in the
following relevant sections.
1. LCD Panel: The IE-1000 is designed for driving 10 bits 120Hz up to 1920x1200 LVDS panels.
Due to the variation between manufacturers of panels signal timing and other panel
characteristics it is important to use the correct Digital View Connection Diagram (which can be
downloaded from the Digital View Controller Solution Generator at
www.digitalview.com/controllers/csg.php) before connecting to a panel.
2. Image Enhancer board, IE-1000 : With reference to the Connection Diagram ensure correct
jumper and dip switches settings to match the target LCD panel. Caution: Handle with care as
static charge may damage electronic components.
3. LCD main controller, eg SVH-1920 : With reference to the Connection Diagram ensure correct
jumper and dip switches settings to match the target LCD panel. Caution: Handle the controller
with care as static charge may damage electronic components.
4. Interconnect LVDS cable : This cable connects between the IE-1000 and DigitalView controllers
for transmittion of LVDS signal and panel power to IE-1000 board. It is recommended to organize
loose wires with cable ties. Care should be taken when placing the cables to avoid signal
interference. Additionally it may be necessary in some systems to add ferrite cores to the cable to
minimize signal noise.
5. Panel power cable : This cable connects between IE-1000 and DigitalView controllers for panel
power.
6. Panel cable for LVDS panel : In order to provide a clean signal it is recommended that LCD
signal cables should not be longer than 61cm (24 inches). It is recommended to organize loose
wires with cable ties. Care should be taken when placing the cables to avoid signal interference.
Additionally it may be necessary in some systems to add ferrite cores to the cable to minimize
signal noise.
7. RS-232 interface : This port is relevant for firmware upgrade only.
8. Power Input: 12V/24VDC is required, this should be a regulated supply. The power rating
depends on the panel and inverter used. Normally a power supply with at least 15W power
output should adequate. Although the controller provides power regulation for the LCD power
this does not relate to the power supplied to the backlight inverter. If an unregulated power
supply is provided to an inverter any fluctuations in power may affect operation, performance and
lifetime of the inverter and or backlight tubes.
9. Power and inverter control cable : Different inverter models require different cables and
different pin assignments. Using the wrong cable may damage the inverter.
IMPORTANT NOTES
•Power Safety: We strongly advise using appropriate insulation for all circuitry.
•EMI: Shielding will be required for passing certain regulatory emissions tests.
•Ground: The various PCB mounting holes are connected to the ground plane.

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.4: 26 March, 2009 (IE-1000 -2X manual.doc) Page 5 of 19
•Servicing: The board is not user serviceable or repairable. Warranty does not cover
user error in connecting up to the IE-1000 and is invalidated by unauthorized
modification or repairs.
•Board Mounting: It is recommended that a clearance of at least 10mm is provided above
and 5mm below the board when mounted. Additionally consideration should be given to:
oElectrical insulation.
oGrounding.
oEMI shielding.
oCable management. Note: It is important to keep panel signal cables apart from the
inverter & backlight cables to prevent signal interference.
oHeat & Ventilation: Heat generated from other sources, for example the backlight of a
very high brightness panel may generate significant heat which could adversely affect
the IE-1000.
oOther system design issues that may affect safety or performance.
IMPORTANT: Please read the Application Notes section for more information.

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.4: 26 March, 2009 (IE-1000 -2X manual.doc) Page 6 of 19
CONNECTION & OPERATION
CAUTION: Never connect or disconnect parts of the display system when the system is powered up
as this may cause serious damage.
CONNECTION
Connection and usage is quite straight forward (it is useful to have the relevant connection diagram
available at this time):
1. Connect the LCD panel & IE-1000 : Use the appropriate panel cable as indicated in the relevant
Digital View Connection Diagram.
2. Connect the Digital View main controller & IE-1000:Use LVDS cable P/N 426497600-3,
200mm, this carries both the LVDS signal and panel power.
3. Connect a suitable OSD switch mount kit : Digital View offer a number of ready made options.
4. Check all Jumpers & Switches: Refer to the relevant Digital View Connection Diagram or the
jumpers and switches setting table (in the following section).
5. Connect the Power supply : Plug a DC 12V/24V power source to the connector PP1 or
PP2/PP3. You can consider to use Digital View mating power cable P/N 426013800-3, 160mm for
PP1 connection.
6. Power on : Switch on the controller board and panel by using the OSD switch mount.
Power status on LED5A :
State LED color
Power on state Green
Board status LED on LED1A :
State LED color
Board in operation with valid
signal. GREEN
No signal state RED
Valid signal detected and
board setup in progress ORANGE
General:
•If you are using supplied cables & accessories, ensure they are correct for the model of panel and
controller and IE-1000.
•If you are making your own cables & connectors refer carefully to both the panel & inverter
specifications and the section in this manual, “Connectors, Pinouts & Jumpers” to ensure the
correct pin to pin wiring.

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.4: 26 March, 2009 (IE-1000 -2X manual.doc) Page 7 of 19
IE-1000 BUTTONS & DEMO MODES
•Button switch – TS1 : Board reset : Reset the IE-1000 board.
•Button switch – TS2 : Push TS2 to cycle between the 4 different demo modes while LED1A is
GREEN.
Mode 1 (default) = whole screen with smoothed motion (LED2 GREEN);
Mode 2 = LEFT demo mode, left side of screen with smoothed motion while right side without (LED2
GREEN, a box with yellow border appear on LEFT hand side of screen);
Mode 3 = CENTRE demo mode, centre part of screen with smoothed motion while other areas
without (LED2 GREEN, a box with yellow border appear in the CENTRE of the screen);
Mode 4 = whole screen without smoothed motion (LED2 RED)
IE-1000 will not memorize the demo mode after you turn off the IE-1000. It will resume back to mode
1 always.
* This function will not activate in static text mode (SW2 position 4 sets ON).

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.4: 26 March, 2009 (IE-1000 -2X manual.doc) Page 8 of 19
CONNECTORS, PINOUTS & JUMPERS
The various connectors are:
Summary: Connectors
Ref Purpose Description
CN1 LVDS signal input Hirose 40-pin, DF13A-40DP-1.25DSA
(Matching type : DF13-40DS-1.25C)
(Matching panel cable : P/N 426497600-3, 200mm)
CN2 Additional panel power input Hirose 20-pin, DF13-20DP-1.25 (Matching type : DF13-20DS-1.25C)
CN3 LVDS signal output 1 JST 50-pin, BM50B-SRDS
(Matching type : SHDR-50V-S-B or compatible)
CN4 LVDS signal output 2 JST 40-pin, BM40B-SRDS
(Matching type : SHDR-40V-S-B or compatible)
CN5 Reserved JST 4-pin, S4B-XH-A (Matching type : XHP-4)
CN6 Serial control (for firmware
programming use only) JST 6-pin, S6B-XH-A (Matching type : XHP-6)
CN7 Reserved Hirose 6 ways, DF13-6PV
CN9 Panel backlight control JST 2-way, B2B-XH-A (Matching type : XHP-2)
S1 Power on/off control JST 2-way, B2B-PH-K (Matching type : PHR-2)
PP1 Main input power Molex 43650-0200 compatible
(Matching connector type : Molex 43645-0200 compatible)
(Matching power cable : P/N 426013800-3, 160mm)
PP2/PP3 Alternative power input DC power Molex 2 pin 0.156” pitch

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.4: 26 March, 2009 (IE-1000 -2X manual.doc) Page 9 of 19
Summary: Jumpers setting
Ref
Purpose Note
JA1 On board +5V logic power enable 1-2 & 3-4 closed, factory set, do not remove
JA2 On board +2.5V logic power enable 1-2 & 3-4 closed, factory set, do not remove
JA3 On board +1V logic power enable 1-2 & 3-4 closed, factory set, do not remove
JP1 Reserved Factory sets Open
LED1 Reserved Factory sets Open
LED2 Reserved Factory sets Open
SW2 Function selection See table 1
SW3 Panel selection See table 2
Table 1 : DIP switch selection – SW2
Pos. # Function Description
1 Input signal color bit selection OFF : 8 bit (for SVH-1920)
ON : 10 bit (for SVX-1920 (Coming soon)
2 Input LVDS display mode selection If SW2 position 1 = OFF (8 bit)
OFF : Mapping B
ON : Mapping A
If SW2 position 1 = ON (10 bit)
OFF : JEIDA mode
ON : VESA mode
3 Output LVDS display mode selection OFF : JEIDA mode
ON : VESA mode
Please adjust to get the correct picture. See as Appendix I for details of
mapping of VESA and JEIDA.
4 Motion compensation mode OFF : Enable (for film mode(a))
ON : Disable (for static text mode(b))
Remark :
(a) Film mode – Image with motion pattern
(b) Static text mode – Image with static pattern
Table 2 : DIP Switch selection – SW3
Pos #1 Pos #2 Pos #3 Pos.#4 Description Panel resolution
For WUXGA panels
OFF OFF OFF OFF LG LC370WUD-SAB1 1920x1080
ON OFF OFF OFF NEC NL192120AC25-02 1920x1200
For additional and recent added panels, see panel support table at http://www.digitalview.com/controllers/csg.php

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.4: 26 March, 2009 (IE-1000 -2X manual.doc) Page 10 of 19
CN1 – LVDS signal input connector: Hirose, DF13A-40DP-1.25DSA (Matching type : DF13-40DS-1.25C)
PIN SYMBOL DESCRIPTION
1 LVDS_IN_A0+ Positive differential LVDS data bit A0
2 LVDS_IN_A0- Negative differential LVDS data bit A0
3 LVDS_IN_A1+ Positive differential LVDS data bit A1
4 LVDS_IN_A1- Negative differential LVDS data bit A1
5 OP1 Reserved
6 OP2 Reserved
7 LVDS_IN_A2+ Positive differential LVDS data bit A2
8 LVDS_IN_A2- Negative differential LVDS data bit A2
9 LVDS_IN_A3+ Positive differential LVDS data bit A3
10 LVDS_IN_A3- Negative differential LVDS data bit A3
11 LVDS_IN_A4+ Positive differential LVDS data bit A4
12 LVDS_IN_A4- Negative differential LVDS data bit A4
13 LVDS_IN_AC+ Positive LVDS clock for A channel
14 LVDS_IN_AC- Negative LVDS clock for A channel
15 LVDS_IN_B4+ Positive differential LVDS data bit B4
16 LVDS_IN_B4- Negative differential LVDS data bit B4
17 LVDS_IN_B0+ Positive differential LVDS data bit B0
18 LVDS_IN_B0- Negative differential LVDS data bit B0
19 LVDS_IN_B1+ Positive differential LVDS data bit B1
20 LVDS_IN_B1- Negative differential LVDS data bit B1
21 OP3 Reserved
22 OP4 Reserved
23 LVDS_IN_B2+ Positive differential LVDS data bit B2
24 LVDS_IN_B2- Negative differential LVDS data bit B2
25 LVDS_IN_B3+ Positive differential LVDS data bit B3
26 LVDS_IN_B3- Negative differential LVDS data bit B3
27 GND Ground
28 GND Ground
29 LVDS_IN_BC+ Positive LVDS clock for B channel
30 LVDS_IN_BC- Negative LVDS clock for B channel
31 GND Ground
32 GND Ground
33 VLCD_LV Panel power supply (3,3V/5V) from front end controller
34 VLCD_LV Panel power supply (3,3V/5V) from front end controller
35 VLCD_LV Panel power supply (3,3V/5V) from front end controller
36 VLCD_LV Panel power supply (3,3V/5V) from front end controller
37 NC No connection
38 VLCD_HV Panel power supply (+12V/18V) from front end controller
39 VLCD_HV Panel power supply (+12V/18V) from front end controller
40 VLCD_HV Panel power supply (+12V/18V) from front end controller
CN2 – Additional panel power input connector : HIROSE D13-20DP-1.25 (Matching type : DF13-20DS-1.25C)
PIN SYMBOL DESCRIPTION
1 VLCD_LV Panel power supply (3,3V/5V) from front end controller
2 VLCD_LV Panel power supply (3,3V/5V) from front end controller
3 VLCD_LV Panel power supply (3,3V/5V) from front end controller
4 VLCD_LV Panel power supply (3,3V/5V) from front end controller
5 VLCD_LV Panel power supply (3,3V/5V) from front end controller
6 VLCD_LV Panel power supply (3,3V/5V) from front end controller
7 GND Ground
8 GND Ground
9 GND Ground
10 GND Ground
11 GND Ground
12 GND Ground
13 GND Ground
14 GND Ground
15 VLCD_HV Panel power supply (+12V/18V) from front end controller
16 VLCD_HV Panel power supply (+12V/18V) from front end controller
17 VLCD_HV Panel power supply (+12V/18V) from front end controller
18 VLCD_HV Panel power supply (+12V/18V) from front end controller
19 VLCD_HV Panel power supply (+12V/18V) from front end controller
20 VLCD_HV Panel power supply (+12V/18V) from front end controller

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.4: 26 March, 2009 (IE-1000 -2X manual.doc) Page 11 of 19
CN3 – LVDS signal output connector : JST BM50B-SRDS (Matching type : SHDR-50V-S-B)
PIN SYMBOL DESCRIPTION
1 LVDS_OUT1_B0+ Positive differential LVDS data bit B0
2 LVDS_OUT1_B0- Negative differential LVDS data bit B0
3 LVDS_OUT1_B1+ Positive differential LVDS data bit B1
4 LVDS_OUT1_B1- Negative differential LVDS data bit B1
5 OP1 Reserved
6 OP2 Reserved
7 LVDS_OUT1_B2+ Positive differential LVDS data bit B2
8 LVDS_OUT1_B2- Negative differential LVDS data bit B2
9 LVDS_OUT1_BC+ Positive LVDS clock for A channel
10 LVDS_OUT1_BC- Negative LVDS clock for A channel
11 LVDS_OUT1_B3+ Positive differential LVDS data bit B3
12 LVDS_OUT1_B3- Negative differential LVDS data bit B3
13 LVDS_OUT1_B4+ Positive differential LVDS data bit B4
14 LVDS_OUT1_B4- Negative differential LVDS data bit B4
15 LVDS_OUT1_A0+ Positive differential LVDS data bit A0
16 LVDS_OUT1_A0- Negative differential LVDS data bit A0
17 LVDS_OUT1_A1+ Positive differential LVDS data bit A1
18 LVDS_OUT1_A1- Negative differential LVDS data bit A1
19 LVDS_OUT1_A2+ Positive differential LVDS data bit A2
20 LVDS_OUT1_A2- Negative differential LVDS data bit A2
21 OP3 Reserved
22 OP4 Reserved
23 LVDS_OUT1_AC+ Positive LVDS clock for A channel
24 LVDS_OUT1_AC- Negative LVDS clock for A channel
25 LVDS_OUT1_A3+ Positive differential LVDS data bit A3
26 LVDS_OUT1_A3- Negative differential LVDS data bit A3
27 GND Ground
28 GND Ground
29 LVDS_OUT1_A4+ Positive differential LVDS data bit A4
30 LVDS_OUT1_A4- Negative differential LVDS data bit A4
31 GND Ground
32 GND Ground
33 GND Ground
34 GND Ground
35 GND Ground
36 GND Ground
37 VLCD_LV Panel power supply (3,3V/5V) from front end controller
38 VLCD_LV Panel power supply (3,3V/5V) from front end controller
39 VLCD_LV Panel power supply (3,3V/5V) from front end controller
40 VLCD_LV Panel power supply (3,3V/5V) from front end controller
41 VLCD_LV Panel power supply (3,3V/5V) from front end controller
42 VLCD_LV Panel power supply (3,3V/5V) from front end controller
43 NC No connection
44 VLCD_HV Panel power supply (+12V/18V) from front end controller
45 VLCD_HV Panel power supply (+12V/18V) from front end controller
46 VLCD_HV Panel power supply (+12V/18V) from front end controller
47 VLCD_HV Panel power supply (+12V/18V) from front end controller
48 VLCD_HV Panel power supply (+12V/18V) from front end controller
49 VLCD_HV Panel power supply (+12V/18V) from front end controller
50 VLCD_HV Panel power supply (+12V/18V) from front end controller
CN4 – LVDS signal output connector : JST BM40B-SRDS (Matching type : SHDR-40V-S-B)
PIN SYMBOL DESCRIPTION
1 LVDS_OUT2_B0+ Positive differential LVDS data bit B0
2 LVDS_OUT2_B0- Negative differential LVDS data bit B0
3 LVDS_OUT2_B1+ Positive differential LVDS data bit B1
4 LVDS_OUT2_B1- Negative differential LVDS data bit B1
5 OP1 Reserved
6 OP2 Reserved
7 LVDS_OUT2_B2+ Positive differential LVDS data bit B2
8 LVDS_OUT2_B2- Negative differential LVDS data bit B2
9 LVDS_OUT2_BC+ Positive LVDS clock for A channel
10 LVDS_OUT2_BC- Negative LVDS clock for A channel
11 LVDS_OUT2_B3+ Positive differential LVDS data bit B3
12 LVDS_OUT2_B3- Negative differential LVDS data bit B3
13 LVDS_OUT2_B4+ Positive differential LVDS data bit B4
14 LVDS_OUT2_B4- Negative differential LVDS data bit B4

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.4: 26 March, 2009 (IE-1000 -2X manual.doc) Page 12 of 19
15 LVDS_OUT2_A0+ Positive differential LVDS data bit A0
16 LVDS_OUT2_A0- Negative differential LVDS data bit A0
17 LVDS_OUT2_A1+ Positive differential LVDS data bit A1
18 LVDS_OUT2_A1- Negative differential LVDS data bit A1
19 LVDS_OUT2_A2+ Positive differential LVDS data bit A2
20 LVDS_OUT2_A2- Negative differential LVDS data bit A2
21 OP3 Reserved
22 OP4 Reserved
23 LVDS_OUT2_AC+ Positive LVDS clock for A channel
24 LVDS_OUT2_AC- Negative LVDS clock for A channel
25 LVDS_OUT2_A3+ Positive differential LVDS data bit A3
26 LVDS_OUT2_A3- Negative differential LVDS data bit A3
27 GND Ground
28 GND Ground
29 LVDS_OUT2_A4+ Positive differential LVDS data bit A4
30 LVDS_OUT2_A4- Negative differential LVDS data bit A4
31 GND Ground
32 GND Ground
33 VLCD_LV Panel power supply (3,3V/5V) from front end controller
34 VLCD_LV Panel power supply (3,3V/5V) from front end controller
35 VLCD_LV Panel power supply (3,3V/5V) from front end controller
36 VLCD_LV Panel power supply (3,3V/5V) from front end controller
37 NC No connection
38 VLCD_HV Panel power supply (+12V/18V) from front end controller
39 VLCD_HV Panel power supply (+12V/18V) from front end controller
40 VLCD_HV Panel power supply (+12V/18V) from front end controller
CN6 – RS-232 serial control (for firmware programming use only) : JST B6B-XH-A (Matching type : XHP-6)
PIN SYMBOL DESCRIPTION
1 SDATA Reserved
2 SCLK Reserved
3 VCC +5V
4 TXD RS-232 Tx data
5 GND Ground
6 RXD RS-232 Rx data
CN9 - Panel backlight control : JST 2-way, B2B-XH-A (Matching type : XHP-2)
PIN DESCRIPTION
1 Ground
2 Backlight status control
S1 - Power on/off selection : JST 2-way, B2B-PH-K (Matching type : PHR-2)
PIN DESCRIPTION
1 +5V logic signal
2 +5V logic signal
PP1 - 12VDC power supply
PIN DESCRIPTION
1 +12V / +24VDC
2 Ground
PP2/PP3 – Alternate 12V/24VDC power supply
PIN DESCRIPTION
1 +12VDC / 24VDC in
2 Ground

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.4: 26 March, 2009 (IE-1000 -2X manual.doc) Page 13 of 19
BOARD DIMENSIONS
The maximum thickness of the IE-1000 is 20.65mm with or without video add-on board
(measured from bottom of PCB to top of components, including any underside components &
leads). We recommend clearances of:
•5mm from bottom of PCB - if mounting on a metal plate we also recommend a layer of
suitable insulation material is added to the mounting plate surface.
•10mm above the components
•3~5mm around the edges
Any of the holes shown above can be used for mounting the PCB, they are 3.2mm in
diameter.
CAUTION: Ensure adequate insulation is provided for all areas of the PCB with special
attention to high voltage parts such as the inverter.

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.4: 26 March, 2009 (IE-1000 -2X manual.doc) Page 14 of 19
TROUBLESHOOTING
General
A general guide to troubleshooting a flat panel display system it is worth considering the system as
separate elements, such as:
¾Controller (jumpers, PC settings)
¾Panel (Cabling, connection, panel, PC settings)
¾Backlight (inverter, cabling, backlight tubes)
¾Cabling
¾Computer system (display settings, operating system)
Through step by step cross checking with instruction manuals and a process of elimination to isolate
the problem it is usually possible to clearly identify the problem area.
No image:
¾If the panel backlight is not working it may still be possible to just see some image on the display.
¾A lack of image is most likely to be caused by incorrect connection, lack of power, failure to
provide a signal or incorrect graphic card settings.
Image position:
If it is impossible to position the image correctly, i.e. the image adjustment controls will not move the
image far enough, then test using another graphics card. This situation can occur with a custom
graphics card that is not close to standard timings or if something is in the graphics line that may be
affecting the signal such as a signal splitter (please note that normally a signal splitter will not have
any adverse effect).
Image appearance:
¾A faulty panel can have blank lines, failed sections, flickering or flashing display
¾Incorrect graphics card refresh rate, resolution or interlaced mode will probably cause the image
to be the wrong size, to scroll, flicker badly or possibly even no image.
¾Incorrect jumper settings on the controller & IE-1000 may cause everything from total failure to
incorrect image. CAUTION: Do not set the panel power input incorrectly.
¾Sparkling on the display: faulty panel signal cable.
Backlight:
Items to check include: Power input, Controls, Inverter and Tubes generally in this order.
If half the screen is dimmer than the other half:
¾Check cabling for the inverter.
¾For a specific backlight tube check the AC pins orientation (CAUTION: Never reverse any DC
power pins).
Also:
¾If adjusting brightness control has no effect the chances are that the VR rating or method of
adjusting brightness is not compatible or correctly connected to the inverter.
¾If system does not power down when there is a loss of signal
Continued failure:
If unit after unit keeps failing consider and investigate whether you are short circuiting the equipment
or doing something else seriously wrong.
Generally after common sense issues have been resolved we recommend step by step substitution of
known working parts to isolate the problem.

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.4: 26 March, 2009 (IE-1000 -2X manual.doc) Page 15 of 19
SPECIFICATIONS
Panel compatibility Compatible with 120Hz panel with 1920x1200, 1920x1080 resolutions.
A specified BIOS and some factory adjustment may be required for individual panel
timings.
No. of colours Up to 10 bit per color, providing 1.07 billion colours.
Panel signal LVDS
Board dimensions 127mm x 91.4mm (5” x 3.6”)
Power consumption 15W approx. (not including panel power consumption)
Input voltage 12V/24VDC +/- 5%
Storage temperature limits -40oC to +70oC
Operating temperature limits 0oC to +60oC
NOTES
Please note the following:
•For specific panel setup a sample of an LCD may be required (this will be returned) and a
copy of the full technical specifications for the panel from the manufacturer.
•Re-layout and custom development services are available.

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.4: 26 March, 2009 (IE-1000 -2X manual.doc) Page 16 of 19
Appendix I – Mapping definition
•Definition of VESA :

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.4: 26 March, 2009 (IE-1000 -2X manual.doc) Page 17 of 19
•Definition of JEIDA :

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.4: 26 March, 2009 (IE-1000 -2X manual.doc) Page 18 of 19
WARRANTY
The products are warranted against defects in workmanship and material for a period of three (3) year
from the date of purchase provided no modifications are made to it and it is operated under normal
conditions and in compliance with the instruction manual.
The warranty does not apply to:
•Product that has been installed incorrectly, this specifically includes but is not limited to cases
where electrical short circuit is caused.
•Product that has been altered or repaired except by the manufacturer (or with the manufacturer’s
consent).
•Product that has subjected to misuse, accidents, abuse, negligence or unusual stress whether
physical or electrical.
•Ordinary wear and tear.
Except for the above express warranties, the manufacturer disclaims all warranties on products
furnished hereunder, including all implied warranties of merchantability and fitness for a particular
application or purpose. The stated express warranties are in lieu of all obligations or liabilities on the
part of the manufacturer for damages, including but not limited to special, indirect consequential
damages arising out of or in connection with the use of or performance of the products.
CAUTION
Whilst care has been taken to provide as much detail as possible for use of this product it
cannot be relied upon as an exhaustive source of information. This product is for use by
suitably qualified persons who understand the nature of the work they are doing and are able
to take suitable precautions and design and produce a product that is safe and meets
regulatory requirements.
LIMITATION OF LIABILITY
The manufacturer’s liability for damages to customer or others resulting from the use of any product
supplied hereunder shall in no event exceed the purchase price of said product.
TRADEMARKS
The following are trademarks of Digital View Ltd:
•Digital View
•IE-1000

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.4: 26 March, 2009 (IE-1000 -2X manual.doc) Page 19 of 19
CONTACT DETAILS
Digital View has offices in Asia, Europe and USA :
USA
Digital View Inc.
18440 Technology Drive
Building 130
Morgan Hill,
California, 95037
USA
Tel: [phone] Fax: [phone]
Sales: [email protected]
EUROPE
Digital View Ltd.
6 Marylebone Passage,
London, W1W 8EX,
UK.
Tel: [phone] Fax: Fax: [phone]
Sales: u[email protected]
ASIA
Digital View Ltd
16 th Floor Millennium City 3
370 Kwun Tong Road
Kwun Tong
Hong Kong
Tel: [phone] Fax: [phone]
Sales: [email protected]
WEBSITE
www.digitalview.com