Direct Place 1022301 User manual

Assembly Instructions - Please keep for future reference
Assembly Instructions - Please keep for future reference
1022301
Issue 1 - 15-10-2012
Scandi - 2 Door 3 Drawer Wardrobe
Dimensions
Width
Depth
Height
:
:
:
350209 MDF
81.1 cm
49.0 cm
191.3 cm

!Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Care and maintenance
1
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not recommend the use
of power drill/drivers for
inserting screws, as this could
damage the unit. Only use hand
screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page
with these instructions for
future reference.

Components - Panels
Please check you have all the panels listed below
2
350209-03 MDF
2
(183,3 cm x 47,5 cm)
Side, right
1
(183,3 cm x 47,5 cm)
Side, left
6
(79,2 cm x 8 cm)
Top rail
4
(78,1 cm x 6 cm)
Plinth, back
12
(45 cm x 9,8 cm)
Drawer side, right/left
10
(77,2 cm x 2,2 cm)
Hanging rail
15
(122,5 cm x 1,7 cm)
H-Profile
13
(74,9 cm x 9,8 cm)
Drawer back
11
(79,3 cm x 15,7 cm)
Drawer front
14
(75,9 cm x 44,7 cm)
Drawer bottom
5
(79,3 cm x 9,6 cm)
Plinth, front
8
(124,5 cm x 39,5 cm)
Door, left
9
(124,5 cm x 39,5 cm)
Door, right
3
(78,1 cm x 47,2 cm)
Top/bottom
7
(174,1 cm x 39,7 cm)
Back
2
x
2
x
3
x
3
x
6
x
3
x

Components - Fittings
Please check you have all the panels listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
3350174-04 MDF
10 ø7.8 x 40mm Wooden dowel x
Aa Ab
ø6 x 30mm Wooden dowel x 12
Cb
ø5 x 11, cc34mm Bolt x 20
Ca
ø15 x 10.5mm Cam x
20
ø4 x 35mm Screw x
Jc
8
1.2 x 20mm Nail x
Da
50
Kb
ø5.8 x 8mm Screw x
18
Sk
6 245 x 17 x 10mm Drawer runner x
Yd
1 Nail holder x
Gc
8 ø40 x 35mm Wooden Knob x
ø3.5 x 15mm Screw x
Bc
18
Mc
4
0mm Crossplate x
Me
4
ø26mm Cup hinge x
Fl
2
Support for hanger rail - 15mm x Wall strap and instruction x 1
Fh
17060 16040 90 15013070 120100 14011050 803020100
Ruler - Use this ruler to help correctly identify the screws
Tools required
Flatblade screwdriver
(Medium)
Hammer Phillips screwdriver
(Medium & large)
Ke
8
ø6.1 x 11.5mm Screw x
Magnet, adjustable x
Pc
4
35 x 12 x 1mm Magnet catch x
Pd
4
Back fitting w. ø3.5 x 15mm Screw x
Fi
6
Va
Angle 20 x 20 x 16mm x 4 2
Vg
50 x 50 x 15mm Angle x
ø3 x 12mm Screw x
Bo
4
ø3 x 35mm Screw x
Bp
12
Hk
6
M4 x 9mm Screw x
350209-04 MDF

Assembly Instructions
Knock the dowels
Ab
into the holes indicated
on the drawer sides 12
using a smal hammer.
Step 2
Step 4
Screw the bolts
Cb
into
the holes indicated on
the drawer front 11 .
Fix the drawer sides 12
to the drawer back 13 as
shown, using screws
Bp
.
Step 1
Slide the drawer bottom
14 into the drawer
sides 12 .
Step 3
Step 5
Push the drawer front 11
onto the drawer sides 12
as shown.
Push cams
Ca
into the
holes indicated. Arrow
pointing towards the front.
Turn the cams
Ca
to the
right to x the front 11 .
4
350174-05
12
13
12
14
11
11
Bp
Bp
Ab
Ab
Cb
Cb
Ca
Ca
Cb
Ca
12
12
12
12
12
12
3
x
3
x
3
x
3
x
3
x
350209-05

Assembly Instructions
Step 6
!
Important!
Make sure the
angle between
the drawer front
11
and
the drawer sides
12
is 90°
before the drawer bottom
14
is xed.
Fix the drawer bottom
14
to
the drawer back
13
and the
drawer front
11
using
Fi
.
To adjust the angle between
the drawer sides and the
drawer fronts push the tting
Fi
sidewards. See details.
Step 7
Fix the wooden knobs
Gc
to the drawer front 11
using screws
Jc
.
Fix the support for hanger
rail
Fl
to the sides
1
and
2
using screws
Bc
.
Fix the Crossplates
Mc
to
the sides
1
and
2
using
the pre-mounted screws.
Note the details.
Position the
Crossplates
Mc
exactly
as shown.
Screw the bolts
Cb
into
the holes indicated on the
sides
1
and
2
.
Fix the angles
Va
to the
sides
1
and
2
using
screws
Ke
. Place the
angles as shown.
See details.
Step 8
350174-06
5
90°
90°
90° 90°
90°
1
2
Cb
Cb
Cb
Cb
Cb
Cb
Cb
Cb
Cb
Cb
Cb
Cb
Cb
Cb
Fi
Fi
Gc
Gc
Ke
Va
Fl
Bc
Fl
Bc
Ke
Va
Mc
Mc
Mc
Mc
11
13
14
11
3
x
3
x
12
12
Fi
Fi Fi
Jc
Jc
350209-06

Assembly Instructions
Slide the top of the
drawer runners
Sk
backwards.
Fix the front end of the
drawer runners
Sk
to the
sides 1and 2using
screws
Kb
through the
holes indicated.
See details.
Step 9
Slide the top of the draw-
er runners
Sk
forwards.
Fix the back end of the
drawer runners
Sk
to the
sides 1and 2using
screws
Kb
through the
holes indicated.
See details.
Step 10
6
350174-07
Kb
Sk
Sk
Kb
Kb
Kb
Kb
Sk
Sk
Sk
Sk
Sk
Sk
Sk
Kb
Kb
Kb
Kb
1
2
2
1
Kb
Sk
Kb
Kb
Kb
Kb
Kb
Kb
Kb
Kb
350209-07

Assembly Instructions
Place the sides
1and 2
onto the
top 3, the
bottom 3
and the back
plinth 4.
Push cams
Ca
into the
holes indicated
on the top 3,
the bottom 3and
the back plinth 4.
Arrows pointing towards
the sides 1and 2.
Turn the cams
Ca
to the
right to x the sides 1
and 2.
Step 12
Knock the dowels
Aa
into
the holes indicated on
the top/bottom 3and
the back plinth 4using
a small hammer.
Press the magnets
Pc
into the holes indicated
on the top/bottom 3.
Step 11
Fix the front plinth 5
onto the angles
Va
using
screw
Ke
.
Step 13
350174-08
7
x2
3
Aa
Aa
Pc Pc
Aa
Aa
Ca
Ca
Ca
Ca
Ca
Ca
Ca
Ca
Ca
Ca
3
1
23
4
5
Ke
Ke
4
Aa
Aa
350209-08

Assembly Instructions
Step 14
Place the backs 7into
the rabbets in the sides
1and 2and the
H-prole 15 .
!
Important!
Make sure the
angle between
the top
3
and the sides
1
and
2
is 90° when the
backs
7
is attached.
Fix the backs
7
to the
sides 1and 2, the top
3and the back plinth
4
using nails
Da
.
Use the nail holder
Yd
and a
small hammer.
Place the top rail 6onto
the top 3.
Fix the top rail 6to the
top 3using angles
Vg
and screws
Bc
.
Step 15
350174-08
7
x2
3
Aa
Aa
Pc Pc
Aa
Aa
Ca
Ca
Ca
Ca
Ca
Ca
Ca
Ca
Ca
Ca
3
1
23
4
5
Ke
Ke
4
Aa
Aa
8
350209-09
Yd
Da
Da
Da
Da
Da
7
7
15
Bc
Bc
6
6
Bc
Bc Vg
Vg
6
3
1
6
3
3mm
1
3
2
4

Assembly Instructions
Step 16
!Warning!
The wardrobe is
heavy.
Lift with care.
Its recommended that the
wardrobe is xed to the wall.
Use the ttings
Fh
. Follow
the instructions included
with the ttings.
Pull out the drawer
runners. Slide the
drawers onto the
runners.
Fit and x the lower
drawer rst and work
your way up.
Fix drawers to the drawer
runners using screws
Hk
.
350209-10
9
Hk
Hk
Wall strap and instruction
x Fh 1
Hk

Assembly Instructions
Place the cup hinges
Me
into the holes indicated
on the doors 8and 9.
Fix the hinges using
screws
Bc
.
Fix the magnet catches
Pd
using screws
Bo
into
the holes indicated.
Step 17
Place the hanger rail
10
into the supports
Fl
.
Slide the cup hinges
Me
onto the crossplates
Mc
Fix the hinges using the
premounted screw in the
crossplates.
See details above on how
to t the cup hinge
Me
onto the cross plate
Mc
.
Step 18
Fix the wooden knobs
Gc
to the doors 8and
9using screws
Jc
and
adjust the magnets
Pc
.
10
350209-11 MDF
Bc
Me
Me
Bc
Bc
Me
8
9
Bc
Me
Bo
Pd
Pd
Bo
Bo
Pd
Pd
Bo
Tighten these screws
10
Gc
Gc
8
9
Jc
Jc
Fl
Pc
Pc
!
!
Mc
Me
Me
Mc

Assembly Instructions
Adjusting the doors
left/right.
a:
To adjust the door
towards the left hand
side - turn the adjusting
screw to the right.
b:
To adjust the door
towards the right hand
side - turn the adjusting
screw to the left.
Step 19
Adjusting the doors
forwards/backwards.
a:
Loosen the xing screw.
b:
Push the cup hinges /
the door forwards OR
backwards to adjust.
c:
Tighten the xing screws
of ALL the crossplates.
Adjusting the doors
up/down.
a:
Loosen the two pre-mounted
screws of each crossplate,
BUT ONLY as much as it
will allow the cross plate to
move up and down.
b:
Push the the door up OR
down to adjust.
c:
Tighten the pre-mounted
screws of ALL the
crossplates.
350209-12 MDF
11
a: b:
a: b: c:
a: b: c: