Directed Electronics 690XV User manual

MMooddeell669900XXVV
➤
OOwwnneerr’’ssGGuuiiddee

i
© 2003 directed electronics, inc.
lliimmiitteeddlliiffeettiimmeeccoonnssuummeerrwwaarrrraannttyy
Directed Electronics, Inc. ("Directed") promises to the original purchaser to repair or
replace with a comparable reconditioned model any Directed unit (hereafter the "unit"),
excluding without limitation the siren, the remote transmitters, the associated sensors and
accessories, which proves to be defective in workmanship or material under reasonable use
during the lifetime of the vehicle provided the following conditions are met: the unit was
professionally installed and serviced by an authorized Directed dealer; the unit will be pro-
fessionally reinstalled in the vehicle in which it was originally installed by an authorized
Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy
of the bill of sale or other dated proof of purchase bearing the following information: con-
sumer's name, telephone number and address; the authorized dealers name, telephone
number and address; complete product description, including accessories; the year, make
and model of the vehicle; vehicle license number and vehicle identification number. All
components other than the unit, including without limitation the siren, the remote trans-
mitters and the associated sensors and accessories, carry a one-year warranty from the date
of purchase of the same. This warranty is non-transferable and is automatically void if: the
original purchaser has not completed the warranty card and mailed it within ten (10) days
of the date of purchase to the address listed on the card; the unit's date code or serial num-
ber is defaced, missing or altered; the unit has been modified or used in a manner con-
trary to its intended purpose; the unit has been damaged by accident, unreasonable use,
neglect, improper service, installation or other causes not arising out of defects in materi-
als or construction. The warranty does not cover damage to the unit caused by installa-
tion or removal of the unit. Directed, in its sole discretion, will determine what consti-
tutes excessive damage and may refuse the return of any unit with excessive damage. TO
THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUD-
ING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY,
WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE
AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY,
ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR
AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY,
OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS.
DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY
AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEAL-
ERS OR INSTALLERS. DIRECTED SECURITY SYSTEMS, INCLUDING THIS
UNIT, ARE DETERRENTS AGAINST POSSIBLE THEFT. DIRECTED IS NOT
OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAM-
AGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS; AND
HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUD-
ING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR
VANDALISM. THIS WARRANTY DOES NOT COVER LABOR COSTS FOR
MAINTENANCE, REMOVAL OR REINSTALLATION OF THE UNIT OR ANY

ii © 2003 directed electronics, inc.
CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM
OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER
VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA.
CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY
AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY
CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE
AUTHORIZED DIRECTED DEALER'S PURCHASE PRICE OF THE UNIT.
DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEV-
ER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES,
INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF
EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY
AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER
DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CON-
TROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on
how long an implied warranty will last or the exclusion or limitation of incidental or con-
sequential damages. This warranty gives you specific legal rights and you may also have
other rights that vary from State to State.
This product may be covered by a Guaranteed Protection Plan ("GPP"). See your autho-
rized Directed dealer for details of the plan or call Directed Customer Service at 1-800-
876-0800. Directed security systems, including this unit, are deterrents against possible
theft. Directed is not offering a guarantee or insurance against vandalism, damage or theft
of the automobile, its parts or contents; and hereby expressly disclaims any liability what-
soever, including without limitation, liability for theft, damage and/or vandalism.
Directed does not and has not authorized any person or entity to create for it any other
obligation, promise, duty or obligation in connection with this security system.
Make sure you have all of the following information from your dealer:
A clear copy of the sales receipt, showing the following:
➤Date of purchase
➤Your full name and address
➤Authorized dealer's company name and address
➤Type of alarm installed
➤Year, make, model and color of the automobile
➤Automobile license number
➤Vehicle identification number
➤All security options installed on automobile
➤Installation receipts

1
© 2003 directed electronics, inc.
ttaabblleeooffccoonntteennttss
lliimmiitteeddlliiffeettiimmeeccoonnssuummeerrwwaarrrraannttyy................................................................................ii
rreemmootteeccoonnttrroollddiiaaggrraamm................................................................................................22
ssttaannddaarrddrreemmootteeccoonnffiigguurraattiioonnss....................................................................................33
wwhhaattiissiinncclluuddeedd............................................................................................................44
iimmppoorrttaannttiinnffoorrmmaattiioonn..................................................................................................44
system maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
your warrantywarranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
fcc/id notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
rreemmootteeccoonnttrroollffuunnccttiioonnss..............................................................................................77
standard button configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
standard icon configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
rreemmootteeooppeerraattiioonnaannddpprrooggrraammmmiinnggiinnssttrruuccttiioonnss........................................................1111
system signal paging features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
programmable remote control features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
uussiinnggyyoouurrssyysstteemm......................................................................................................1155
active arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
passive arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
multi-level security arming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
arming while driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
high security disarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
disarming without a transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
silent mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
panic mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
valet mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
nuisance prevention® circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
ddiiaaggnnoossttiiccss..................................................................................................................2244
arming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
disarming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
system status chirps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
table of zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
interpreting zone diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
ccooddeehhooppppiinngg..............................................................................................................2277
hhiigghhffrreeqquueennccyy............................................................................................................2288
oowwnneerrrreeccooggnniittiioonn......................................................................................................2288
rraappiiddrreessuummeellooggiicc......................................................................................................2299
ppoowweerrssaavveerrmmooddee......................................................................................................2299
pprrooggrraammmmiinnggooppttiioonnss................................................................................................3300
iinnssttaallllaattiioonnooppttiioonnss....................................................................................................3333
vveehhiicclleerreeccoovveerryyssyysstteemm((vvrrss®®))....................................................................................3344
arming the vrs® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
vrs® triggered sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
gglloossssaarryyoofftteerrmmss........................................................................................................3377
sseeccuurriittyy&&ccoonnvveenniieenncceeeexxppaannssiioonnss............................................................................3399
qquuiicckkrreeffeerreenncceegguuiiddee..................................................................................................4411

2© 2003 directed electronics, inc.
rreemmootteeccoonnttrroollddiiaaggrraamm

3
© 2003 directed electronics, inc.
ssttaannddaarrddrreemmootteeccoonnffiigguurraattiioonnss
1 Auxiliary Channel Out
2 Receive Indicator
3 Signal Indicator
4 Transmit Indicator
5 Lock Status Indicator
6 Unlock Status Indicator
7 Arming Status Indicator
8 Disarming Status Indicator
9 Door Switch Input Indicator
10 Warn Away®Response Indicator
11 Siren Status Indicator
12 Battery Level Indicator
13 Trigger ResponseIndicator
14 Hood Switch Input Indicator
15 Ignition Switch Input Indicator
16 Sensor Response Indicator
17 Sensor 1 Indicator - Full Trigger and Warn Away®
18 Sensor 2 Indicator - Full Trigger and Warn Away®
19 Trunk Switch Input Indicator
20 Vibrate Mode Indicator
21 Remote Start Indicator (n/a)
22 Disarm Button
23 Panic Button
24 Auxiliary Button
25 Arm Button

4© 2003 directed electronics, inc.
wwhhaattiissiinncclluuddeedd
➤One control module
➤One Responder transceiver
➤Stinger® Doubleguard® dual-stage shock sensor
➤Revenger® Soft Chirp® six-tone programmable siren
➤Status LED indicator light
➤Push-button Valet button
➤Your warranty registration
➤Failsafe® Starter Kill ready circuitry
(may require additional labor)
➤FSK transceiver
iimmppoorrttaannttiinnffoorrmmaattiioonn
Congratulations on the purchase of your state-of-the-art vehicle
security system. This system has been designed to provide years
of trouble-free operation. Due to the complexity of this system,
it must be installed by an authorized dealer only. Installation of
this product by anyone other than an authorized dealer voids the
warranty. All dealers are provided with preprinted dealer certifi-
cates to verify that they are authorized.
This owner’s guide should help you to get the most out of your
system. Please take the time to read it prior to using the system.

5
© 2003 directed electronics, inc.
system maintenance
This system needs no specific maintenance beyond remote
control battery replacement. The remote is powered by a 1.5V
AAA battery.
The Battery Level indicator has four level indicators that serve as
a visual indication of battery charge. When the battery reaches a
low charge level that requires replacement, the remote control
will generate a single notification chirp, and the Battery Level
indicator will flash continuously.
Battery Replacement
Gently pull the end of the battery door away from the top of the
remote control then slide the door up to expose the battery and
remove the expired battery. Place the new battery into the
remote control observing the correct polarity. When power is
returned the remote control will light all icons in the LCD and
generate all beeper tones once.
your warrantywarranty
Your warranty registration must be returned and the bar code
serial number must not be removed. If the warranty registration
is not returned, you do not have a warranty. It is also necessary
to keep your proof of purchase, which reflects that the product
was installed by an authorized dealer. Make sure that you receive
the warranty registration from your dealer.
➜
EMPTY
REPLACE
FULL
➜

6© 2003 directed electronics, inc.
fcc/id notice
This device complies with Part 15 of FCC rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate this device.
Tested to Comply
with FCC Standards
Directed Electronics, Inc. 436 Series
DRW-368
➜

7
© 2003 directed electronics, inc.
rreemmootteeccoonnttrroollffuunnccttiioonnss
The remote control buttons are used to send commands to the
system. The descriptions below reflect the standard configura-
tion for this system. The buttons can be custom configured for
the user’s specific needs by the installer.
standard button configurations
Button
The System Arm and Multi-Level Security Arming functions are
controlled by pressing this button for one second.
Button
The System Disarm and High Security Disarm functions are
controlled by pressing this button for one second.
Button
Silent Mode™ and an optional auxiliary function are controlled
by this button. Silent Mode works by pressing this button for
less than one second before arming or disarming. An optional
auxiliary function, such as trunk release, can be controlled by
pressing this button for 1.5 seconds.
The auxiliary output controls __________________________.
Button
The panic feature is controlled by pressing this button for two
seconds.
➜

8© 2003 directed electronics, inc.
and Buttons
An optional auxiliary convenience or expansion function that
you have added to your system can be activated by pressing these
buttons simultaneously.
The auxiliary output controls __________________________.
standard icon configurations
Icon
The transmit icon will be displayed while the remote control is
transmitting a command to the vehicle.
Icon
The receive icon will be displayed while the remote control is
receiving a page from the vehicle.
Icon
The signal icon will be displayed if a command is transmitted to
the vehicle but a command page is not received.
Icon
The armed status icon will be displayed when the system is locked
and armed.
Icon
The disarmed status icon will be displayed when the system is
unlocked and disarmed.
Icon
The disarm icon will flash while the system is disarming
➜

9
© 2003 directed electronics, inc.
Icon
The arm icon will flash while the system is arming.
Icon
The door icon will be displayed to indicate that a door is open
when arming the system (Bypass Notification) or opened when
the system is armed (Tamper Alert).
Icon
The warn icon will be displayed if the Warn Away®response has
been triggered while the system is armed.
Icon
The siren icon will be displayed as an indicator that the siren is
sounding.
Icon
The alarm icon will be displayed if the system has been violated,
and will continue to be displayed until the 60-second siren cycle
is complete.
Icon
The vibrate icon will be displayed when the Vibrate Mode is on.
Icon
The battery level icon is always displayed as an indicator of
Battery charge.

10 © 2003 directed electronics, inc.
Icon
The start icon is not used in this model.
Icon
The trunk icon will be displayed to indicate that the trunk is
open when arming the system (Bypass Notification) or opened
when the system is armed (Tamper Alert).
Icon
The Sensor 1 icon will be displayed if the Dual-Stage shock
sensor has been triggered as a full-triggered or Warn Away®
sequence.
Icon
The Sensor 2 icon will be displayed if an additional Dual-Stage
sensor has been triggered as a full-triggered or Warn Away®
sequence.
Icon
The hammer icon will flash when either Sensor 1 or 2 has been
triggered as either a Warn Away®response or triggered sequence.
Icon
The ignition icon will be displayed to indicate that the ignition
is on when arming the system (Bypass Notification) or turned on
when the system is armed (Tamper Alert).
Icon
The hood icon will be displayed to indicate that the hood is open
when arming the system or (Bypass Notification) opened when
the system is armed (Tamper Alert).

11
© 2003 directed electronics, inc.
Number Icons
When either of the channel 2 or 3 outputs is activated the appro-
priate icon will be displayed for five seconds.
rreemmootteeooppeerraattiioonnaannddpprrooggrraamm--
mmiinnggiinnssttrruuccttiioonnss
This security system operates at 434 MHz and incorporates
Directed’s proprietary XHF2 out-board Responder Technology
remote control. The high frequency combined with Binary Data
communication achieves superior range with two-way commu-
nication.
system signal paging features
A page is the signal the control module sends to the remote
control as confirmation of receipt of a command or alarm system
status.
When the remote control receives a page it will generate a page
notification to the user (notifications are audible beeps or remote
vibration) and the LCD Icons will display the current system
status.
Command Page
When a command (arm/disarm, remote start, or auxiliary
channel) from the remote control is sent and received, the system
will send a command page back to confirm receipt.
➜

12 © 2003 directed electronics, inc.
Alarm Page
If the alarm system is triggered while armed, an Alarm Page will
be sent to the remote control. After receipt of an Alarm Page, the
LCD icons will display the alarm system status information and
the remote control will generate Alarm Page alerts.
An Alarm Page alert is a single beep or vibration from the remote
control every 60 seconds to alert the user that the alarm system
was triggered and will continue until the alarm page is cleared.
Page Recognition Mode
The remote control will leave a zone icon illuminated when it
has received a triggered response and will wait for you to recog-
nize the violation. Press any button on the remote control, the
LCD information and Alarm Page alerts will be cleared.
note: The remote control buttons will not send a com-
mand to the system until the alarm page is cleared.
note: If the transmiter is paged with an Alarm Page and
the WarnAway®is triggered before the Alarm Page is
recieved the transmitter will report the WarnAway®only
until the system is disarmed.
note: When the system is in Valet mode, the remote con-
trol will show the lock (5) and unlock (6) icons, but will
not generate a command page.

13
© 2003 directed electronics, inc.
programmable remote control features
To enter programming mode
Press and hold all four remote control buttons simultaneously
until one long beep is heard. Programming Mode has now been
entered.
Page Notification
The remote control can be programmed to notify the user of a
page by audibly beeping or remote vibration.
Beep Mode
Beep Mode includes alarm arm/disarm diagnostic beeps and
distinctive two-tone remote start beeps.
Vibrate Mode
Vibrate Mode makes page notification silent but does not include
diagnostic information or distinctive remote start notification.
Illumination
Illumination for the LCD display can be programmed on or off.
When programmed on the LCD will illuminate every time the
remote control receives a page or transmits a command.
Programming illumination on will decrease the life expectancy of
the battery.
Beep/Vibrate Mode
Within five seconds of entering Programming Mode, press .
The remote control will beep once for on, twice for off. The
vibrate icon (13) will also turn on/off with each press.
➜

14 © 2003 directed electronics, inc.
Illumination On/Off
Within five seconds of entering Programming Mode, press
. The remote will beep once for on, twice for off and the light
will turn on/off with each press.
Page Mode On/Off
After entering Programming Mode, press within five
seconds to toggle on and off. When the Page Mode is on, the
remote control will wake up periodically to check for messages
from the security module. It will also wake up when any button
is pushed. When Page Mode is off, the remote control “sleeps”
until a button is pushed, extending the life of the battery.
Channel 1 Zone Select
After entering Programming Mode, press within five
seconnds to toggle between hood, trunk, and hood and trunk.
The remote will bep once and show hood icon for hood, beep
twice and show trunk icon for trunk, and will beepthree time
and show both icons for hood and trunk. The default is the tunk.
To Exit Programming Mode
To exit Programming Mode, take no action for five seconds. The
remote control will generate two beeps to indicate programming
mode has been exited.

15
© 2003 directed electronics, inc.
uussiinnggyyoouurrssyysstteemm
The buttons used in the instructions in this manual correspond
to the standard configuration. Remember, this is not the only
way your transmitter may be set up. It can be custom configured
to meet your needs.
active arming
You can activate, or arm, the system by pressing on your
transmitter for one second. When the system arms, you will hear
a short siren sound, or chirp, and the parking lights will flash
once. If the vehicle’s power door locks have been connected to
the system, the doors will lock.
While the system is armed, the status LED will flash approxi-
mately once per second, indicating that the system is actively
protecting your vehicle. If you hear a second chirp after arming,
and see the status LED flashing in groups, refer to the Diagnostics
section of this guide. This extra chirp is called Bypass Notification.
passive arming
The system also can be programmed to arm itself automatically
(called passive arming). If the system is programmed for passive
arming, it will automatically arm 30 seconds after the ignition is
turned off and the system "sees" you leave the vehicle by opening
and closing a door. Whenever the system is in its 30-second
passive-arming countdown, the status LED will flash twice as
➜
➜

16 © 2003 directed electronics, inc.
fast as it does when the system is armed. The siren will chirp
once 20 seconds after the last door has been closed. The system
is not actually armed at that point. The system arms and the
doors lock (if connected and programmed for passive locking) at
the 30 second mark, but the siren will not chirp. The early chirp
provides you with a 10-second warning prior to arming.
When armed, your vehicle is protected as follows:
➤Light impacts will trigger the Warn Away®signal. When
triggered, the siren will chirp and the parking lights will flash
for a few seconds.
➤Heavy impacts will trigger the system. The triggered
sequence is between 1-180 seconds of constant siren and
flashing parking lights.
➤If a door is opened, the system will immediately start
chirping the siren and flashing the parking lights. Three
seconds later, the siren output changes to a continuous blast.
This progressive response gives you time to disarm the sys-
tem with your transmitter if you inadvertently open the door
while the system is armed, while still providing an instant
response (even if the door is immediately closed).
note: If any protected entry point (such as a door or a
switch-protected trunk or hood) is open, the system will
not passively arm (unless forced passive arming is pro-
grammed on). See Programming Options section of this
guide. Additionally, each time a protected entry is trig-
gered during the arming countdown, the 30-second
countdown starts over.

17
© 2003 directed electronics, inc.
➤Turning on the ignition key will trip the same two-stage
response as opening a door.
➤The optional starter kill prevents the vehicle’s starter from
cranking.
multi-level security arming
Multi-Level Security Arming allows you to select which of the
security system's inputs or sensors will be active and which will
be bypassed at the time that the system is armed. (See the Table
of Zones section of this guide.) Pressing again within five
seconds of arming the security system will activate the Multi-
Level Security Arming feature. Each time is pressed again, a
different security level is selected. The different security levels
can be selected as follows:
➤Press one time: The siren chirps once. The system is
armed.
➤Press a second time within five seconds: The siren
chirps twice followed by a long chirp. Zone 2 is now
bypassed.
➤Press a third time within five seconds: The siren chirps
three times followed by a long chirp. Zone 4 is now
bypassed.
➤Press a fourth time within five seconds: The siren chirps
four times followed by a long chirp. Zones 2 and 4 are now
bypassed.
➤Press a fifth time within five seconds: The siren chirps
five times followed by a long chirp. All input zones, except
➜