Discount Displays STDRD-MONITOR STAND Manual

STDRD-MONITOR STAND
ASSEMBLE
(A) vertical supports
CONNECT
corners together (A/C)
INSERT
(D/A) middle supports
LOCK
(B) with hand tool
FRAME
Step 1: Assemble 3-part Vertical Supports (A) with plastic grommets facing out.
Step 2: Using the Hand Tool (B), attach the top and bottom Horizontal Supports
(C) to the Vertical Supports (A) by turning the screw with the star-shaped hole
clockwise.
NOTE: Make sure the thin groove is along the outer edge of each piece so the
groove is continuous around the frame.
Step 3: Using the Hand Tool (B), attach the Cross Supports (D) in the same man-
ner at the 2 joints in the Vertical Supports (A).
NOTE: The 3rd Cross Support (D) is included for added support or for use as a
spare replacement piece.
GRAPHIC
Step 1: Make sure the frame is laying flat on the floor and the star-holed screws
are facing down.
Step 2: Start with each corner and attach Fabric (F) by rolling fabric in and push-
ing the rubber beading into the thin groove along the edge of the frame with your
thumb.
Step 3: After the corners are secured, continue pushing the rubber beading into
the groove along the sides, top and bottom of the frame.
NOTE: The corners of the stitching should be at the corners of the frame. Over
stretching the fabric will result in uneven bunching of the fabric. Pull the
fabric just tight enough to lay flat.
Step 4: insert assembled frame and graphic (with the print facing torwards the
long side of the base) onto the posts of base.
A A
D
D
C
C
F

ATTACHING AND SECURING THE MONITOR
Step 1: VESA Mount. Before attaching your monitor (not included), be sure the
top 2 screw holes on the back are 15.75” (400mm) apart.
Step 2: Determine the height you would like your monitor to hang.
NOTE: The holes on the frame will be at the same height as the screw holes
on the monitor.
Step 3: Pull the fabric away from the frame at the location of the desired screw
hole and attach the Monitor Profile Bar (G) using the T-Bolt and Wing Nut (H).
Step 4: Attach the appropriate T-Bolts (I) into the top screw holes on the monitor
and the correspondingly-sized Leveling Bolts (J) into the lower screw holes.
NOTE: The extra sets of bolts are for other mount patterns and will not be
needed. Do not screw bolts in too far as it can crack the screen. Most
monitors allow for at least 1/4” depth.
Step 5: Attach the monitor by adjusting the hook on one side of the Monitor
Profile Bar (G) so the ball is outside the groove allowing the T-Bolts (I) to slide into
the groove. Once both bolts are secured in the groove, re-adjust the hooks so the
ball is in the groove. This prevents the monitor from sliding o.
Step 6: Slowly tighten or loosen the Leveling Bolt for Monitor (J) to adjust the
angle of the monitor.
STDRD-MONITOR STAND
STEP 1: VESA MOUNT
STEP 2: MONITOR PLACEMENT
STEP 4: BOLT ATTACHMENTS FOR MONITOR
MOUNTING HOLES
BACK OF MONITOR
400mm (15.75”)
6” or less

SECURING AND LEVELING THE FRAME
Step 1: Attach the Eye Nut with Wing Bolt (K) through the hole in the center of
the top Horizontal Support (C).
Step 2: Attach the Eye Bolt (L) to the base at the screw hole insert located at
the back.
Step 3: Connect the Tension Wire (M) - First, the the Carabiner to the top Eye
Nut (K) and then the Tension Screw to the Eye Bolt (L) on the base.
Step 4: Turn the middle of the tension screw until the wire is tight and the
display frame is level.
ASSEMBLING AND MOUNTING THE HEADER GRAPHIC
Step 1: Connect the tubing segments that are bungee corded together. Each
locking push pin should snap in place.
Step 2: The “T” shaped pieces slide into the two holes located closest to the
inside of the frame.
Step 3: Unzip the fabric graphic and slide over the tubing frame so the graphic
faces forward (convex side).
Step 4: Zip graphic closed around the outside edge making sure that the “T”
tubes protrude through the holes on the back (concave side) of the graphic.
Step 5: Slide the angled tube supports onto the ends of the “T” tubes protrud-
ing through the graphic and tighten with wing nuts.
Step 6: Slide the angled tube supports into the plastic holes at the top of
the frame.
STDRD-MONITOR STAND
1
1
5
4
6
3
3